424 lines
10 KiB
Plaintext
424 lines
10 KiB
Plaintext
|
* Generic Exynos Bus frequency device
|
||
|
|
||
|
The Samsung Exynos SoC has many buses for data transfer between DRAM
|
||
|
and sub-blocks in SoC. Most Exynos SoCs share the common architecture
|
||
|
for buses. Generally, each bus of Exynos SoC includes a source clock
|
||
|
and a power line, which are able to change the clock frequency
|
||
|
of the bus in runtime. To monitor the usage of each bus in runtime,
|
||
|
the driver uses the PPMU (Platform Performance Monitoring Unit), which
|
||
|
is able to measure the current load of sub-blocks.
|
||
|
|
||
|
The Exynos SoC includes the various sub-blocks which have the each AXI bus.
|
||
|
The each AXI bus has the owned source clock but, has not the only owned
|
||
|
power line. The power line might be shared among one more sub-blocks.
|
||
|
So, we can divide into two type of device as the role of each sub-block.
|
||
|
There are two type of bus devices as following:
|
||
|
- parent bus device
|
||
|
- passive bus device
|
||
|
|
||
|
Basically, parent and passive bus device share the same power line.
|
||
|
The parent bus device can only change the voltage of shared power line
|
||
|
and the rest bus devices (passive bus device) depend on the decision of
|
||
|
the parent bus device. If there are three blocks which share the VDD_xxx
|
||
|
power line, Only one block should be parent device and then the rest blocks
|
||
|
should depend on the parent device as passive device.
|
||
|
|
||
|
VDD_xxx |--- A block (parent)
|
||
|
|--- B block (passive)
|
||
|
|--- C block (passive)
|
||
|
|
||
|
There are a little different composition among Exynos SoC because each Exynos
|
||
|
SoC has different sub-blocks. Therefore, such difference should be specified
|
||
|
in devicetree file instead of each device driver. In result, this driver
|
||
|
is able to support the bus frequency for all Exynos SoCs.
|
||
|
|
||
|
Required properties for all bus devices:
|
||
|
- compatible: Should be "samsung,exynos-bus".
|
||
|
- clock-names : the name of clock used by the bus, "bus".
|
||
|
- clocks : phandles for clock specified in "clock-names" property.
|
||
|
- operating-points-v2: the OPP table including frequency/voltage information
|
||
|
to support DVFS (Dynamic Voltage/Frequency Scaling) feature.
|
||
|
|
||
|
Required properties only for parent bus device:
|
||
|
- vdd-supply: the regulator to provide the buses with the voltage.
|
||
|
- devfreq-events: the devfreq-event device to monitor the current utilization
|
||
|
of buses.
|
||
|
|
||
|
Required properties only for passive bus device:
|
||
|
- devfreq: the parent bus device.
|
||
|
|
||
|
Optional properties only for parent bus device:
|
||
|
- exynos,saturation-ratio: the percentage value which is used to calibrate
|
||
|
the performance count against total cycle count.
|
||
|
- exynos,voltage-tolerance: the percentage value for bus voltage tolerance
|
||
|
which is used to calculate the max voltage.
|
||
|
|
||
|
Detailed correlation between sub-blocks and power line according to Exynos SoC:
|
||
|
- In case of Exynos3250, there are two power line as following:
|
||
|
VDD_MIF |--- DMC
|
||
|
|
||
|
VDD_INT |--- LEFTBUS (parent device)
|
||
|
|--- PERIL
|
||
|
|--- MFC
|
||
|
|--- G3D
|
||
|
|--- RIGHTBUS
|
||
|
|--- PERIR
|
||
|
|--- FSYS
|
||
|
|--- LCD0
|
||
|
|--- PERIR
|
||
|
|--- ISP
|
||
|
|--- CAM
|
||
|
|
||
|
- In case of Exynos4210, there is one power line as following:
|
||
|
VDD_INT |--- DMC (parent device)
|
||
|
|--- LEFTBUS
|
||
|
|--- PERIL
|
||
|
|--- MFC(L)
|
||
|
|--- G3D
|
||
|
|--- TV
|
||
|
|--- LCD0
|
||
|
|--- RIGHTBUS
|
||
|
|--- PERIR
|
||
|
|--- MFC(R)
|
||
|
|--- CAM
|
||
|
|--- FSYS
|
||
|
|--- GPS
|
||
|
|--- LCD0
|
||
|
|--- LCD1
|
||
|
|
||
|
- In case of Exynos4x12, there are two power line as following:
|
||
|
VDD_MIF |--- DMC
|
||
|
|
||
|
VDD_INT |--- LEFTBUS (parent device)
|
||
|
|--- PERIL
|
||
|
|--- MFC(L)
|
||
|
|--- G3D
|
||
|
|--- TV
|
||
|
|--- IMAGE
|
||
|
|--- RIGHTBUS
|
||
|
|--- PERIR
|
||
|
|--- MFC(R)
|
||
|
|--- CAM
|
||
|
|--- FSYS
|
||
|
|--- GPS
|
||
|
|--- LCD0
|
||
|
|--- ISP
|
||
|
|
||
|
- In case of Exynos5422, there are two power line as following:
|
||
|
VDD_MIF |--- DREX 0 (parent device, DRAM EXpress controller)
|
||
|
|--- DREX 1
|
||
|
|
||
|
VDD_INT |--- NoC_Core (parent device)
|
||
|
|--- G2D
|
||
|
|--- G3D
|
||
|
|--- DISP1
|
||
|
|--- NoC_WCORE
|
||
|
|--- GSCL
|
||
|
|--- MSCL
|
||
|
|--- ISP
|
||
|
|--- MFC
|
||
|
|--- GEN
|
||
|
|--- PERIS
|
||
|
|--- PERIC
|
||
|
|--- FSYS
|
||
|
|--- FSYS2
|
||
|
|
||
|
- In case of Exynos5433, there is VDD_INT power line as following:
|
||
|
VDD_INT |--- G2D (parent device)
|
||
|
|--- MSCL
|
||
|
|--- GSCL
|
||
|
|--- JPEG
|
||
|
|--- MFC
|
||
|
|--- HEVC
|
||
|
|--- BUS0
|
||
|
|--- BUS1
|
||
|
|--- BUS2
|
||
|
|--- PERIS (Fixed clock rate)
|
||
|
|--- PERIC (Fixed clock rate)
|
||
|
|--- FSYS (Fixed clock rate)
|
||
|
|
||
|
Example1:
|
||
|
Show the AXI buses of Exynos3250 SoC. Exynos3250 divides the buses to
|
||
|
power line (regulator). The MIF (Memory Interface) AXI bus is used to
|
||
|
transfer data between DRAM and CPU and uses the VDD_MIF regulator.
|
||
|
|
||
|
- MIF (Memory Interface) block
|
||
|
: VDD_MIF |--- DMC (Dynamic Memory Controller)
|
||
|
|
||
|
- INT (Internal) block
|
||
|
: VDD_INT |--- LEFTBUS (parent device)
|
||
|
|--- PERIL
|
||
|
|--- MFC
|
||
|
|--- G3D
|
||
|
|--- RIGHTBUS
|
||
|
|--- FSYS
|
||
|
|--- LCD0
|
||
|
|--- PERIR
|
||
|
|--- ISP
|
||
|
|--- CAM
|
||
|
|
||
|
- MIF bus's frequency/voltage table
|
||
|
-----------------------
|
||
|
|Lv| Freq | Voltage |
|
||
|
-----------------------
|
||
|
|L1| 50000 |800000 |
|
||
|
|L2| 100000 |800000 |
|
||
|
|L3| 134000 |800000 |
|
||
|
|L4| 200000 |825000 |
|
||
|
|L5| 400000 |875000 |
|
||
|
-----------------------
|
||
|
|
||
|
- INT bus's frequency/voltage table
|
||
|
----------------------------------------------------------
|
||
|
|Block|LEFTBUS|RIGHTBUS|MCUISP |ISP |PERIL ||VDD_INT |
|
||
|
| name| |LCD0 | | | || |
|
||
|
| | |FSYS | | | || |
|
||
|
| | |MFC | | | || |
|
||
|
----------------------------------------------------------
|
||
|
|Mode |*parent|passive |passive|passive|passive|| |
|
||
|
----------------------------------------------------------
|
||
|
|Lv |Frequency ||Voltage |
|
||
|
----------------------------------------------------------
|
||
|
|L1 |50000 |50000 |50000 |50000 |50000 ||900000 |
|
||
|
|L2 |80000 |80000 |80000 |80000 |80000 ||900000 |
|
||
|
|L3 |100000 |100000 |100000 |100000 |100000 ||1000000 |
|
||
|
|L4 |134000 |134000 |200000 |200000 | ||1000000 |
|
||
|
|L5 |200000 |200000 |400000 |300000 | ||1000000 |
|
||
|
----------------------------------------------------------
|
||
|
|
||
|
Example2 :
|
||
|
The bus of DMC (Dynamic Memory Controller) block in exynos3250.dtsi
|
||
|
is listed below:
|
||
|
|
||
|
bus_dmc: bus_dmc {
|
||
|
compatible = "samsung,exynos-bus";
|
||
|
clocks = <&cmu_dmc CLK_DIV_DMC>;
|
||
|
clock-names = "bus";
|
||
|
operating-points-v2 = <&bus_dmc_opp_table>;
|
||
|
status = "disabled";
|
||
|
};
|
||
|
|
||
|
bus_dmc_opp_table: opp_table1 {
|
||
|
compatible = "operating-points-v2";
|
||
|
opp-shared;
|
||
|
|
||
|
opp-50000000 {
|
||
|
opp-hz = /bits/ 64 <50000000>;
|
||
|
opp-microvolt = <800000>;
|
||
|
};
|
||
|
opp-100000000 {
|
||
|
opp-hz = /bits/ 64 <100000000>;
|
||
|
opp-microvolt = <800000>;
|
||
|
};
|
||
|
opp-134000000 {
|
||
|
opp-hz = /bits/ 64 <134000000>;
|
||
|
opp-microvolt = <800000>;
|
||
|
};
|
||
|
opp-200000000 {
|
||
|
opp-hz = /bits/ 64 <200000000>;
|
||
|
opp-microvolt = <825000>;
|
||
|
};
|
||
|
opp-400000000 {
|
||
|
opp-hz = /bits/ 64 <400000000>;
|
||
|
opp-microvolt = <875000>;
|
||
|
};
|
||
|
};
|
||
|
|
||
|
bus_leftbus: bus_leftbus {
|
||
|
compatible = "samsung,exynos-bus";
|
||
|
clocks = <&cmu CLK_DIV_GDL>;
|
||
|
clock-names = "bus";
|
||
|
operating-points-v2 = <&bus_leftbus_opp_table>;
|
||
|
status = "disabled";
|
||
|
};
|
||
|
|
||
|
bus_rightbus: bus_rightbus {
|
||
|
compatible = "samsung,exynos-bus";
|
||
|
clocks = <&cmu CLK_DIV_GDR>;
|
||
|
clock-names = "bus";
|
||
|
operating-points-v2 = <&bus_leftbus_opp_table>;
|
||
|
status = "disabled";
|
||
|
};
|
||
|
|
||
|
bus_lcd0: bus_lcd0 {
|
||
|
compatible = "samsung,exynos-bus";
|
||
|
clocks = <&cmu CLK_DIV_ACLK_160>;
|
||
|
clock-names = "bus";
|
||
|
operating-points-v2 = <&bus_leftbus_opp_table>;
|
||
|
status = "disabled";
|
||
|
};
|
||
|
|
||
|
bus_fsys: bus_fsys {
|
||
|
compatible = "samsung,exynos-bus";
|
||
|
clocks = <&cmu CLK_DIV_ACLK_200>;
|
||
|
clock-names = "bus";
|
||
|
operating-points-v2 = <&bus_leftbus_opp_table>;
|
||
|
status = "disabled";
|
||
|
};
|
||
|
|
||
|
bus_mcuisp: bus_mcuisp {
|
||
|
compatible = "samsung,exynos-bus";
|
||
|
clocks = <&cmu CLK_DIV_ACLK_400_MCUISP>;
|
||
|
clock-names = "bus";
|
||
|
operating-points-v2 = <&bus_mcuisp_opp_table>;
|
||
|
status = "disabled";
|
||
|
};
|
||
|
|
||
|
bus_isp: bus_isp {
|
||
|
compatible = "samsung,exynos-bus";
|
||
|
clocks = <&cmu CLK_DIV_ACLK_266>;
|
||
|
clock-names = "bus";
|
||
|
operating-points-v2 = <&bus_isp_opp_table>;
|
||
|
status = "disabled";
|
||
|
};
|
||
|
|
||
|
bus_peril: bus_peril {
|
||
|
compatible = "samsung,exynos-bus";
|
||
|
clocks = <&cmu CLK_DIV_ACLK_100>;
|
||
|
clock-names = "bus";
|
||
|
operating-points-v2 = <&bus_peril_opp_table>;
|
||
|
status = "disabled";
|
||
|
};
|
||
|
|
||
|
bus_mfc: bus_mfc {
|
||
|
compatible = "samsung,exynos-bus";
|
||
|
clocks = <&cmu CLK_SCLK_MFC>;
|
||
|
clock-names = "bus";
|
||
|
operating-points-v2 = <&bus_leftbus_opp_table>;
|
||
|
status = "disabled";
|
||
|
};
|
||
|
|
||
|
bus_leftbus_opp_table: opp_table1 {
|
||
|
compatible = "operating-points-v2";
|
||
|
opp-shared;
|
||
|
|
||
|
opp-50000000 {
|
||
|
opp-hz = /bits/ 64 <50000000>;
|
||
|
opp-microvolt = <900000>;
|
||
|
};
|
||
|
opp-80000000 {
|
||
|
opp-hz = /bits/ 64 <80000000>;
|
||
|
opp-microvolt = <900000>;
|
||
|
};
|
||
|
opp-100000000 {
|
||
|
opp-hz = /bits/ 64 <100000000>;
|
||
|
opp-microvolt = <1000000>;
|
||
|
};
|
||
|
opp-134000000 {
|
||
|
opp-hz = /bits/ 64 <134000000>;
|
||
|
opp-microvolt = <1000000>;
|
||
|
};
|
||
|
opp-200000000 {
|
||
|
opp-hz = /bits/ 64 <200000000>;
|
||
|
opp-microvolt = <1000000>;
|
||
|
};
|
||
|
};
|
||
|
|
||
|
bus_mcuisp_opp_table: opp_table2 {
|
||
|
compatible = "operating-points-v2";
|
||
|
opp-shared;
|
||
|
|
||
|
opp-50000000 {
|
||
|
opp-hz = /bits/ 64 <50000000>;
|
||
|
};
|
||
|
opp-80000000 {
|
||
|
opp-hz = /bits/ 64 <80000000>;
|
||
|
};
|
||
|
opp-100000000 {
|
||
|
opp-hz = /bits/ 64 <100000000>;
|
||
|
};
|
||
|
opp-200000000 {
|
||
|
opp-hz = /bits/ 64 <200000000>;
|
||
|
};
|
||
|
opp-400000000 {
|
||
|
opp-hz = /bits/ 64 <400000000>;
|
||
|
};
|
||
|
};
|
||
|
|
||
|
bus_isp_opp_table: opp_table3 {
|
||
|
compatible = "operating-points-v2";
|
||
|
opp-shared;
|
||
|
|
||
|
opp-50000000 {
|
||
|
opp-hz = /bits/ 64 <50000000>;
|
||
|
};
|
||
|
opp-80000000 {
|
||
|
opp-hz = /bits/ 64 <80000000>;
|
||
|
};
|
||
|
opp-100000000 {
|
||
|
opp-hz = /bits/ 64 <100000000>;
|
||
|
};
|
||
|
opp-200000000 {
|
||
|
opp-hz = /bits/ 64 <200000000>;
|
||
|
};
|
||
|
opp-300000000 {
|
||
|
opp-hz = /bits/ 64 <300000000>;
|
||
|
};
|
||
|
};
|
||
|
|
||
|
bus_peril_opp_table: opp_table4 {
|
||
|
compatible = "operating-points-v2";
|
||
|
opp-shared;
|
||
|
|
||
|
opp-50000000 {
|
||
|
opp-hz = /bits/ 64 <50000000>;
|
||
|
};
|
||
|
opp-80000000 {
|
||
|
opp-hz = /bits/ 64 <80000000>;
|
||
|
};
|
||
|
opp-100000000 {
|
||
|
opp-hz = /bits/ 64 <100000000>;
|
||
|
};
|
||
|
};
|
||
|
|
||
|
|
||
|
Usage case to handle the frequency and voltage of bus on runtime
|
||
|
in exynos3250-rinato.dts is listed below:
|
||
|
|
||
|
&bus_dmc {
|
||
|
devfreq-events = <&ppmu_dmc0_3>, <&ppmu_dmc1_3>;
|
||
|
vdd-supply = <&buck1_reg>; /* VDD_MIF */
|
||
|
status = "okay";
|
||
|
};
|
||
|
|
||
|
&bus_leftbus {
|
||
|
devfreq-events = <&ppmu_leftbus_3>, <&ppmu_rightbus_3>;
|
||
|
vdd-supply = <&buck3_reg>;
|
||
|
status = "okay";
|
||
|
};
|
||
|
|
||
|
&bus_rightbus {
|
||
|
devfreq = <&bus_leftbus>;
|
||
|
status = "okay";
|
||
|
};
|
||
|
|
||
|
&bus_lcd0 {
|
||
|
devfreq = <&bus_leftbus>;
|
||
|
status = "okay";
|
||
|
};
|
||
|
|
||
|
&bus_fsys {
|
||
|
devfreq = <&bus_leftbus>;
|
||
|
status = "okay";
|
||
|
};
|
||
|
|
||
|
&bus_mcuisp {
|
||
|
devfreq = <&bus_leftbus>;
|
||
|
status = "okay";
|
||
|
};
|
||
|
|
||
|
&bus_isp {
|
||
|
devfreq = <&bus_leftbus>;
|
||
|
status = "okay";
|
||
|
};
|
||
|
|
||
|
&bus_peril {
|
||
|
devfreq = <&bus_leftbus>;
|
||
|
status = "okay";
|
||
|
};
|
||
|
|
||
|
&bus_mfc {
|
||
|
devfreq = <&bus_leftbus>;
|
||
|
status = "okay";
|
||
|
};
|