87 lines
1.9 KiB
Plaintext
87 lines
1.9 KiB
Plaintext
|
* NXP PCA953x I2C GPIO multiplexer
|
||
|
|
|
||
|
|
Required properties:
|
||
|
|
- compatible: Has to contain one of the following:
|
||
|
|
nxp,pca9505
|
||
|
|
nxp,pca9534
|
||
|
|
nxp,pca9535
|
||
|
|
nxp,pca9536
|
||
|
|
nxp,pca9537
|
||
|
|
nxp,pca9538
|
||
|
|
nxp,pca9539
|
||
|
|
nxp,pca9554
|
||
|
|
nxp,pca9555
|
||
|
|
nxp,pca9556
|
||
|
|
nxp,pca9557
|
||
|
|
nxp,pca9574
|
||
|
|
nxp,pca9575
|
||
|
|
nxp,pca9698
|
||
|
|
nxp,pcal6524
|
||
|
|
nxp,pcal9555a
|
||
|
|
maxim,max7310
|
||
|
|
maxim,max7312
|
||
|
|
maxim,max7313
|
||
|
|
maxim,max7315
|
||
|
|
ti,pca6107
|
||
|
|
ti,pca9536
|
||
|
|
ti,tca6408
|
||
|
|
ti,tca6416
|
||
|
|
ti,tca6424
|
||
|
|
ti,tca9539
|
||
|
|
ti,tca9554
|
||
|
|
onnn,pca9654
|
||
|
|
exar,xra1202
|
||
|
|
- gpio-controller: if used as gpio expander.
|
||
|
|
- #gpio-cells: if used as gpio expander.
|
||
|
|
- interrupt-controller: if to be used as interrupt expander.
|
||
|
|
- #interrupt-cells: if to be used as interrupt expander.
|
||
|
|
|
||
|
|
Optional properties:
|
||
|
|
- interrupts: interrupt specifier for the device's interrupt output.
|
||
|
|
- reset-gpios: GPIO specification for the RESET input. This is an
|
||
|
|
active low signal to the PCA953x.
|
||
|
|
- vcc-supply: power supply regulator.
|
||
|
|
|
||
|
|
Example:
|
||
|
|
|
||
|
|
|
||
|
|
gpio@20 {
|
||
|
|
compatible = "nxp,pca9505";
|
||
|
|
reg = <0x20>;
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&pinctrl_pca9505>;
|
||
|
|
gpio-controller;
|
||
|
|
#gpio-cells = <2>;
|
||
|
|
interrupt-parent = <&gpio3>;
|
||
|
|
interrupts = <23 IRQ_TYPE_LEVEL_LOW>;
|
||
|
|
};
|
||
|
|
|
||
|
|
|
||
|
|
Example with Interrupts:
|
||
|
|
|
||
|
|
|
||
|
|
gpio99: gpio@22 {
|
||
|
|
compatible = "nxp,pcal6524";
|
||
|
|
reg = <0x22>;
|
||
|
|
interrupt-parent = <&gpio6>;
|
||
|
|
interrupts = <1 IRQ_TYPE_EDGE_FALLING>; /* gpio6_161 */
|
||
|
|
interrupt-controller;
|
||
|
|
#interrupt-cells = <2>;
|
||
|
|
vcc-supply = <&vdds_1v8_main>;
|
||
|
|
gpio-controller;
|
||
|
|
#gpio-cells = <2>;
|
||
|
|
gpio-line-names =
|
||
|
|
"hdmi-ct-hpd", "hdmi.ls-oe", "p02", "p03", "vibra", "fault2", "p06", "p07",
|
||
|
|
"en-usb", "en-host1", "en-host2", "chg-int", "p14", "p15", "mic-int", "en-modem",
|
||
|
|
"shdn-hs-amp", "chg-status+red", "green", "blue", "en-esata", "fault1", "p26", "p27";
|
||
|
|
};
|
||
|
|
|
||
|
|
ts3a227@3b {
|
||
|
|
compatible = "ti,ts3a227e";
|
||
|
|
reg = <0x3b>;
|
||
|
|
interrupt-parent = <&gpio99>;
|
||
|
|
interrupts = <14 IRQ_TYPE_EDGE_RISING>;
|
||
|
|
ti,micbias = <0>; /* 2.1V */
|
||
|
|
};
|
||
|
|
|