52 lines
2 KiB
Plaintext
52 lines
2 KiB
Plaintext
|
UniPhier GPIO controller
|
||
|
|
|
||
|
|
Required properties:
|
||
|
|
- compatible: Should be "socionext,uniphier-gpio".
|
||
|
|
- reg: Specifies offset and length of the register set for the device.
|
||
|
|
- gpio-controller: Marks the device node as a GPIO controller.
|
||
|
|
- #gpio-cells: Should be 2. The first cell is the pin number and the second
|
||
|
|
cell is used to specify optional parameters.
|
||
|
|
- interrupt-controller: Marks the device node as an interrupt controller.
|
||
|
|
- #interrupt-cells: Should be 2. The first cell defines the interrupt number.
|
||
|
|
The second cell bits[3:0] is used to specify trigger type as follows:
|
||
|
|
1 = low-to-high edge triggered
|
||
|
|
2 = high-to-low edge triggered
|
||
|
|
4 = active high level-sensitive
|
||
|
|
8 = active low level-sensitive
|
||
|
|
Valid combinations are 1, 2, 3, 4, 8.
|
||
|
|
- ngpios: Specifies the number of GPIO lines.
|
||
|
|
- gpio-ranges: Mapping to pin controller pins (as described in gpio.txt)
|
||
|
|
- socionext,interrupt-ranges: Specifies an interrupt number mapping between
|
||
|
|
this GPIO controller and its interrupt parent, in the form of arbitrary
|
||
|
|
number of <child-interrupt-base parent-interrupt-base length> triplets.
|
||
|
|
|
||
|
|
Optional properties:
|
||
|
|
- gpio-ranges-group-names: Used for named gpio ranges (as described in gpio.txt)
|
||
|
|
|
||
|
|
Example:
|
||
|
|
gpio: gpio@55000000 {
|
||
|
|
compatible = "socionext,uniphier-gpio";
|
||
|
|
reg = <0x55000000 0x200>;
|
||
|
|
interrupt-parent = <&aidet>;
|
||
|
|
interrupt-controller;
|
||
|
|
#interrupt-cells = <2>;
|
||
|
|
gpio-controller;
|
||
|
|
#gpio-cells = <2>;
|
||
|
|
gpio-ranges = <&pinctrl 0 0 0>;
|
||
|
|
gpio-ranges-group-names = "gpio_range";
|
||
|
|
ngpios = <248>;
|
||
|
|
socionext,interrupt-ranges = <0 48 16>, <16 154 5>, <21 217 3>;
|
||
|
|
};
|
||
|
|
|
||
|
|
Consumer Example:
|
||
|
|
|
||
|
|
sdhci0_pwrseq {
|
||
|
|
compatible = "mmc-pwrseq-emmc";
|
||
|
|
reset-gpios = <&gpio UNIPHIER_GPIO_PORT(29, 4) GPIO_ACTIVE_LOW>;
|
||
|
|
};
|
||
|
|
|
||
|
|
Please note UNIPHIER_GPIO_PORT(29, 4) represents PORT294 in the SoC document.
|
||
|
|
Unfortunately, only the one's place is octal in the port numbering. (That is,
|
||
|
|
PORT 8, 9, 18, 19, 28, 29, ... are missing.) UNIPHIER_GPIO_PORT() is a helper
|
||
|
|
macro to calculate 29 * 8 + 4.
|