63 lines
1.7 KiB
Plaintext
63 lines
1.7 KiB
Plaintext
|
* I2C
|
||
|
|
|
||
|
|
Required properties :
|
||
|
|
|
||
|
|
- reg : Offset and length of the register set for the device
|
||
|
|
- compatible : should be "fsl,CHIP-i2c" where CHIP is the name of a
|
||
|
|
compatible processor, e.g. mpc8313, mpc8543, mpc8544, mpc5121,
|
||
|
|
mpc5200 or mpc5200b. For the mpc5121, an additional node
|
||
|
|
"fsl,mpc5121-i2c-ctrl" is required as shown in the example below.
|
||
|
|
|
||
|
|
Recommended properties :
|
||
|
|
|
||
|
|
- interrupts : <a b> where a is the interrupt number and b is a
|
||
|
|
field that represents an encoding of the sense and level
|
||
|
|
information for the interrupt. This should be encoded based on
|
||
|
|
the information in section 2) depending on the type of interrupt
|
||
|
|
controller you have.
|
||
|
|
- fsl,preserve-clocking : boolean; if defined, the clock settings
|
||
|
|
from the bootloader are preserved (not touched).
|
||
|
|
- clock-frequency : desired I2C bus clock frequency in Hz.
|
||
|
|
- fsl,timeout : I2C bus timeout in microseconds.
|
||
|
|
|
||
|
|
Examples :
|
||
|
|
|
||
|
|
/* MPC5121 based board */
|
||
|
|
i2c@1740 {
|
||
|
|
#address-cells = <1>;
|
||
|
|
#size-cells = <0>;
|
||
|
|
compatible = "fsl,mpc5121-i2c", "fsl-i2c";
|
||
|
|
reg = <0x1740 0x20>;
|
||
|
|
interrupts = <11 0x8>;
|
||
|
|
interrupt-parent = <&ipic>;
|
||
|
|
clock-frequency = <100000>;
|
||
|
|
};
|
||
|
|
|
||
|
|
i2ccontrol@1760 {
|
||
|
|
compatible = "fsl,mpc5121-i2c-ctrl";
|
||
|
|
reg = <0x1760 0x8>;
|
||
|
|
};
|
||
|
|
|
||
|
|
/* MPC5200B based board */
|
||
|
|
i2c@3d00 {
|
||
|
|
#address-cells = <1>;
|
||
|
|
#size-cells = <0>;
|
||
|
|
compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c";
|
||
|
|
reg = <0x3d00 0x40>;
|
||
|
|
interrupts = <2 15 0>;
|
||
|
|
interrupt-parent = <&mpc5200_pic>;
|
||
|
|
fsl,preserve-clocking;
|
||
|
|
};
|
||
|
|
|
||
|
|
/* MPC8544 base board */
|
||
|
|
i2c@3100 {
|
||
|
|
#address-cells = <1>;
|
||
|
|
#size-cells = <0>;
|
||
|
|
compatible = "fsl,mpc8544-i2c", "fsl-i2c";
|
||
|
|
reg = <0x3100 0x100>;
|
||
|
|
interrupts = <43 2>;
|
||
|
|
interrupt-parent = <&mpic>;
|
||
|
|
clock-frequency = <400000>;
|
||
|
|
fsl,timeout = <10000>;
|
||
|
|
};
|