88 lines
3.3 KiB
Plaintext
88 lines
3.3 KiB
Plaintext
|
* Broadcom's IPROC Touchscreen Controller
|
||
|
|
|
||
|
|
Required properties:
|
||
|
|
- compatible: must be "brcm,iproc-touchscreen"
|
||
|
|
- ts_syscon: handler of syscon node defining physical base
|
||
|
|
address of the controller and length of memory mapped region.
|
||
|
|
If this property is selected please make sure MFD_SYSCON config
|
||
|
|
is enabled in the defconfig file.
|
||
|
|
- clocks: The clock provided by the SOC to driver the tsc
|
||
|
|
- clock-names: name for the clock
|
||
|
|
- interrupts: The touchscreen controller's interrupt
|
||
|
|
- address-cells: Specify the number of u32 entries needed in child nodes.
|
||
|
|
Should set to 1.
|
||
|
|
- size-cells: Specify number of u32 entries needed to specify child nodes size
|
||
|
|
in reg property. Should set to 1.
|
||
|
|
|
||
|
|
Optional properties:
|
||
|
|
- scanning_period: Time between scans. Each step is 1024 us. Valid 1-256.
|
||
|
|
- debounce_timeout: Each step is 512 us. Valid 0-255
|
||
|
|
- settling_timeout: The settling duration (in ms) is the amount of time
|
||
|
|
the tsc waits to allow the voltage to settle after
|
||
|
|
turning on the drivers in detection mode.
|
||
|
|
Valid values: 0-11
|
||
|
|
0 = 0.008 ms
|
||
|
|
1 = 0.01 ms
|
||
|
|
2 = 0.02 ms
|
||
|
|
3 = 0.04 ms
|
||
|
|
4 = 0.08 ms
|
||
|
|
5 = 0.16 ms
|
||
|
|
6 = 0.32 ms
|
||
|
|
7 = 0.64 ms
|
||
|
|
8 = 1.28 ms
|
||
|
|
9 = 2.56 ms
|
||
|
|
10 = 5.12 ms
|
||
|
|
11 = 10.24 ms
|
||
|
|
- touch_timeout: The continuous number of scan periods in which touch is
|
||
|
|
not detected before the controller returns to idle state.
|
||
|
|
Valid values 0-255.
|
||
|
|
- average_data: Number of data samples which are averaged before a final
|
||
|
|
data point is placed into the FIFO
|
||
|
|
Valid values 0-7
|
||
|
|
0 = 1 sample
|
||
|
|
1 = 2 samples
|
||
|
|
2 = 4 samples
|
||
|
|
3 = 8 samples
|
||
|
|
4 = 16 samples
|
||
|
|
5 = 32 samples
|
||
|
|
6 = 64 samples
|
||
|
|
7 = 128 samples
|
||
|
|
- fifo_threshold: Interrupt is generated whenever the number of fifo
|
||
|
|
entries exceeds this value
|
||
|
|
Valid values 0-31
|
||
|
|
- touchscreen-size-x: horizontal resolution of touchscreen (in pixels)
|
||
|
|
- touchscreen-size-y: vertical resolution of touchscreen (in pixels)
|
||
|
|
- touchscreen-fuzz-x: horizontal noise value of the absolute input
|
||
|
|
device (in pixels)
|
||
|
|
- touchscreen-fuzz-y: vertical noise value of the absolute input
|
||
|
|
device (in pixels)
|
||
|
|
- touchscreen-inverted-x: X axis is inverted (boolean)
|
||
|
|
- touchscreen-inverted-y: Y axis is inverted (boolean)
|
||
|
|
|
||
|
|
Example: An example of touchscreen node
|
||
|
|
|
||
|
|
ts_adc_syscon: ts_adc_syscon@180a6000 {
|
||
|
|
compatible = "brcm,iproc-ts-adc-syscon","syscon";
|
||
|
|
reg = <0x180a6000 0xc30>;
|
||
|
|
};
|
||
|
|
|
||
|
|
touchscreen: touchscreen@180a6000 {
|
||
|
|
compatible = "brcm,iproc-touchscreen";
|
||
|
|
#address-cells = <1>;
|
||
|
|
#size-cells = <1>;
|
||
|
|
ts_syscon = <&ts_adc_syscon>;
|
||
|
|
clocks = <&adc_clk>;
|
||
|
|
clock-names = "tsc_clk";
|
||
|
|
interrupts = <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>;
|
||
|
|
|
||
|
|
scanning_period = <5>;
|
||
|
|
debounce_timeout = <40>;
|
||
|
|
settling_timeout = <7>;
|
||
|
|
touch_timeout = <10>;
|
||
|
|
average_data = <5>;
|
||
|
|
fifo_threshold = <1>;
|
||
|
|
/* Touchscreen is rotated 180 degrees. */
|
||
|
|
touchscreen-inverted-x;
|
||
|
|
touchscreen-inverted-y;
|
||
|
|
};
|