104 lines
1.9 KiB
Plaintext
104 lines
1.9 KiB
Plaintext
|
// SPDX-License-Identifier: GPL-2.0
|
||
|
|
/dts-v1/;
|
||
|
|
#include "bcm2837.dtsi"
|
||
|
|
#include "bcm2835-rpi.dtsi"
|
||
|
|
#include "bcm283x-rpi-smsc9514.dtsi"
|
||
|
|
#include "bcm283x-rpi-usb-host.dtsi"
|
||
|
|
|
||
|
|
/ {
|
||
|
|
compatible = "raspberrypi,3-model-b", "brcm,bcm2837";
|
||
|
|
model = "Raspberry Pi 3 Model B";
|
||
|
|
|
||
|
|
chosen {
|
||
|
|
/* 8250 auxiliary UART instead of pl011 */
|
||
|
|
stdout-path = "serial1:115200n8";
|
||
|
|
};
|
||
|
|
|
||
|
|
memory {
|
||
|
|
reg = <0 0x40000000>;
|
||
|
|
};
|
||
|
|
|
||
|
|
leds {
|
||
|
|
act {
|
||
|
|
gpios = <&expgpio 2 GPIO_ACTIVE_HIGH>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
wifi_pwrseq: wifi-pwrseq {
|
||
|
|
compatible = "mmc-pwrseq-simple";
|
||
|
|
reset-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
&firmware {
|
||
|
|
expgpio: gpio {
|
||
|
|
compatible = "raspberrypi,firmware-gpio";
|
||
|
|
gpio-controller;
|
||
|
|
#gpio-cells = <2>;
|
||
|
|
gpio-line-names = "BT_ON",
|
||
|
|
"WL_ON",
|
||
|
|
"STATUS_LED",
|
||
|
|
"LAN_RUN",
|
||
|
|
"HPD_N",
|
||
|
|
"CAM_GPIO0",
|
||
|
|
"CAM_GPIO1",
|
||
|
|
"PWR_LOW_N";
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
&pwm {
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio41>;
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
&hdmi {
|
||
|
|
hpd-gpios = <&expgpio 4 GPIO_ACTIVE_LOW>;
|
||
|
|
};
|
||
|
|
|
||
|
|
/* uart0 communicates with the BT module */
|
||
|
|
&uart0 {
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&uart0_gpio32 &gpclk2_gpio43>;
|
||
|
|
status = "okay";
|
||
|
|
|
||
|
|
bluetooth {
|
||
|
|
compatible = "brcm,bcm43438-bt";
|
||
|
|
max-speed = <2000000>;
|
||
|
|
shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
/* uart1 is mapped to the pin header */
|
||
|
|
&uart1 {
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&uart1_gpio14>;
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
/* SDHCI is used to control the SDIO for wireless */
|
||
|
|
&sdhci {
|
||
|
|
#address-cells = <1>;
|
||
|
|
#size-cells = <0>;
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&emmc_gpio34>;
|
||
|
|
status = "okay";
|
||
|
|
bus-width = <4>;
|
||
|
|
non-removable;
|
||
|
|
mmc-pwrseq = <&wifi_pwrseq>;
|
||
|
|
|
||
|
|
brcmf: wifi@1 {
|
||
|
|
reg = <1>;
|
||
|
|
compatible = "brcm,bcm4329-fmac";
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
/* SDHOST is used to drive the SD card */
|
||
|
|
&sdhost {
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&sdhost_gpio48>;
|
||
|
|
status = "okay";
|
||
|
|
bus-width = <4>;
|
||
|
|
};
|