65 lines
1.8 KiB
Plaintext
65 lines
1.8 KiB
Plaintext
|
#
|
||
|
|
# Qualcomm network device configuration
|
||
|
|
#
|
||
|
|
|
||
|
|
config NET_VENDOR_QUALCOMM
|
||
|
|
bool "Qualcomm devices"
|
||
|
|
default y
|
||
|
|
---help---
|
||
|
|
If you have a network (Ethernet) card belonging to this class, say Y.
|
||
|
|
|
||
|
|
Note that the answer to this question doesn't directly affect the
|
||
|
|
kernel: saying N will just cause the configurator to skip all
|
||
|
|
the questions about Qualcomm cards. If you say Y, you will be asked
|
||
|
|
for your specific card in the following questions.
|
||
|
|
|
||
|
|
if NET_VENDOR_QUALCOMM
|
||
|
|
|
||
|
|
config QCA7000
|
||
|
|
tristate
|
||
|
|
help
|
||
|
|
This enables support for the Qualcomm Atheros QCA7000.
|
||
|
|
|
||
|
|
config QCA7000_SPI
|
||
|
|
tristate "Qualcomm Atheros QCA7000 SPI support"
|
||
|
|
select QCA7000
|
||
|
|
depends on SPI_MASTER && OF
|
||
|
|
---help---
|
||
|
|
This SPI protocol driver supports the Qualcomm Atheros QCA7000.
|
||
|
|
|
||
|
|
To compile this driver as a module, choose M here. The module
|
||
|
|
will be called qcaspi.
|
||
|
|
|
||
|
|
config QCA7000_UART
|
||
|
|
tristate "Qualcomm Atheros QCA7000 UART support"
|
||
|
|
select QCA7000
|
||
|
|
depends on SERIAL_DEV_BUS && OF
|
||
|
|
---help---
|
||
|
|
This UART protocol driver supports the Qualcomm Atheros QCA7000.
|
||
|
|
|
||
|
|
Currently the driver assumes these device UART settings:
|
||
|
|
Data bits: 8
|
||
|
|
Parity: None
|
||
|
|
Stop bits: 1
|
||
|
|
Flow control: None
|
||
|
|
|
||
|
|
To compile this driver as a module, choose M here. The module
|
||
|
|
will be called qcauart.
|
||
|
|
|
||
|
|
config QCOM_EMAC
|
||
|
|
tristate "Qualcomm Technologies, Inc. EMAC Gigabit Ethernet support"
|
||
|
|
depends on HAS_DMA && HAS_IOMEM
|
||
|
|
select CRC32
|
||
|
|
select PHYLIB
|
||
|
|
---help---
|
||
|
|
This driver supports the Qualcomm Technologies, Inc. Gigabit
|
||
|
|
Ethernet Media Access Controller (EMAC). The controller
|
||
|
|
supports IEEE 802.3-2002, half-duplex mode at 10/100 Mb/s,
|
||
|
|
full-duplex mode at 10/100/1000Mb/s, Wake On LAN (WOL) for
|
||
|
|
low power, Receive-Side Scaling (RSS), and IEEE 1588-2008
|
||
|
|
Precision Clock Synchronization Protocol.
|
||
|
|
|
||
|
|
source "drivers/net/ethernet/qualcomm/rmnet/Kconfig"
|
||
|
|
|
||
|
|
endif # NET_VENDOR_QUALCOMM
|