53 lines
1.6 KiB
Plaintext
53 lines
1.6 KiB
Plaintext
|
Maxim MAX8952 voltage regulator
|
||
|
|
|
||
|
|
Required properties:
|
||
|
|
- compatible: must be equal to "maxim,max8952"
|
||
|
|
- reg: I2C slave address, usually 0x60
|
||
|
|
- max8952,dvs-mode-microvolt: array of 4 integer values defining DVS voltages
|
||
|
|
in microvolts. All values must be from range <770000, 1400000>
|
||
|
|
- any required generic properties defined in regulator.txt
|
||
|
|
|
||
|
|
Optional properties:
|
||
|
|
- max8952,vid-gpios: array of two GPIO pins used for DVS voltage selection
|
||
|
|
- max8952,en-gpio: GPIO used to control enable status of regulator
|
||
|
|
- max8952,default-mode: index of default DVS voltage, from <0, 3> range
|
||
|
|
- max8952,sync-freq: sync frequency, must be one of following values:
|
||
|
|
- 0: 26 MHz
|
||
|
|
- 1: 13 MHz
|
||
|
|
- 2: 19.2 MHz
|
||
|
|
Defaults to 26 MHz if not specified.
|
||
|
|
- max8952,ramp-speed: voltage ramp speed, must be one of following values:
|
||
|
|
- 0: 32mV/us
|
||
|
|
- 1: 16mV/us
|
||
|
|
- 2: 8mV/us
|
||
|
|
- 3: 4mV/us
|
||
|
|
- 4: 2mV/us
|
||
|
|
- 5: 1mV/us
|
||
|
|
- 6: 0.5mV/us
|
||
|
|
- 7: 0.25mV/us
|
||
|
|
Defaults to 32mV/us if not specified.
|
||
|
|
- any available generic properties defined in regulator.txt
|
||
|
|
|
||
|
|
Example:
|
||
|
|
|
||
|
|
vdd_arm_reg: pmic@60 {
|
||
|
|
compatible = "maxim,max8952";
|
||
|
|
reg = <0x60>;
|
||
|
|
|
||
|
|
/* max8952-specific properties */
|
||
|
|
max8952,vid-gpios = <&gpx0 3 0>, <&gpx0 4 0>;
|
||
|
|
max8952,en-gpio = <&gpx0 1 0>;
|
||
|
|
max8952,default-mode = <0>;
|
||
|
|
max8952,dvs-mode-microvolt = <1250000>, <1200000>,
|
||
|
|
<1050000>, <950000>;
|
||
|
|
max8952,sync-freq = <0>;
|
||
|
|
max8952,ramp-speed = <0>;
|
||
|
|
|
||
|
|
/* generic regulator properties */
|
||
|
|
regulator-name = "vdd_arm";
|
||
|
|
regulator-min-microvolt = <770000>;
|
||
|
|
regulator-max-microvolt = <1400000>;
|
||
|
|
regulator-always-on;
|
||
|
|
regulator-boot-on;
|
||
|
|
};
|