102 lines
4.3 KiB
Plaintext
102 lines
4.3 KiB
Plaintext
|
Common Properties for Display Panel
|
||
|
|
===================================
|
||
|
|
|
||
|
|
This document defines device tree properties common to several classes of
|
||
|
|
display panels. It doesn't constitue a device tree binding specification by
|
||
|
|
itself but is meant to be referenced by device tree bindings.
|
||
|
|
|
||
|
|
When referenced from panel device tree bindings the properties defined in this
|
||
|
|
document are defined as follows. The panel device tree bindings are
|
||
|
|
responsible for defining whether each property is required or optional.
|
||
|
|
|
||
|
|
|
||
|
|
Descriptive Properties
|
||
|
|
----------------------
|
||
|
|
|
||
|
|
- width-mm,
|
||
|
|
- height-mm: The width-mm and height-mm specify the width and height of the
|
||
|
|
physical area where images are displayed. These properties are expressed in
|
||
|
|
millimeters and rounded to the closest unit.
|
||
|
|
|
||
|
|
- label: The label property specifies a symbolic name for the panel as a
|
||
|
|
string suitable for use by humans. It typically contains a name inscribed on
|
||
|
|
the system (e.g. as an affixed label) or specified in the system's
|
||
|
|
documentation (e.g. in the user's manual).
|
||
|
|
|
||
|
|
If no such name exists, and unless the property is mandatory according to
|
||
|
|
device tree bindings, it shall rather be omitted than constructed of
|
||
|
|
non-descriptive information. For instance an LCD panel in a system that
|
||
|
|
contains a single panel shall not be labelled "LCD" if that name is not
|
||
|
|
inscribed on the system or used in a descriptive fashion in system
|
||
|
|
documentation.
|
||
|
|
|
||
|
|
|
||
|
|
Display Timings
|
||
|
|
---------------
|
||
|
|
|
||
|
|
- panel-timing: Most display panels are restricted to a single resolution and
|
||
|
|
require specific display timings. The panel-timing subnode expresses those
|
||
|
|
timings as specified in the timing subnode section of the display timing
|
||
|
|
bindings defined in
|
||
|
|
Documentation/devicetree/bindings/display/panel/display-timing.txt.
|
||
|
|
|
||
|
|
|
||
|
|
Connectivity
|
||
|
|
------------
|
||
|
|
|
||
|
|
- ports: Panels receive video data through one or multiple connections. While
|
||
|
|
the nature of those connections is specific to the panel type, the
|
||
|
|
connectivity is expressed in a standard fashion using ports as specified in
|
||
|
|
the device graph bindings defined in
|
||
|
|
Documentation/devicetree/bindings/graph.txt.
|
||
|
|
|
||
|
|
- ddc-i2c-bus: Some panels expose EDID information through an I2C-compatible
|
||
|
|
bus such as DDC2 or E-DDC. For such panels the ddc-i2c-bus contains a
|
||
|
|
phandle to the system I2C controller connected to that bus.
|
||
|
|
|
||
|
|
|
||
|
|
Control I/Os
|
||
|
|
------------
|
||
|
|
|
||
|
|
Many display panels can be controlled through pins driven by GPIOs. The nature
|
||
|
|
and timing of those control signals are device-specific and left for panel
|
||
|
|
device tree bindings to specify. The following GPIO specifiers can however be
|
||
|
|
used for panels that implement compatible control signals.
|
||
|
|
|
||
|
|
- enable-gpios: Specifier for a GPIO connected to the panel enable control
|
||
|
|
signal. The enable signal is active high and enables operation of the panel.
|
||
|
|
This property can also be used for panels implementing an active low power
|
||
|
|
down signal, which is a negated version of the enable signal. Active low
|
||
|
|
enable signals (or active high power down signals) can be supported by
|
||
|
|
inverting the GPIO specifier polarity flag.
|
||
|
|
|
||
|
|
Note that the enable signal control panel operation only and must not be
|
||
|
|
confused with a backlight enable signal.
|
||
|
|
|
||
|
|
- reset-gpios: Specifier for a GPIO coonnected to the panel reset control
|
||
|
|
signal. The reset signal is active low and resets the panel internal logic
|
||
|
|
while active. Active high reset signals can be supported by inverting the
|
||
|
|
GPIO specifier polarity flag.
|
||
|
|
|
||
|
|
Power
|
||
|
|
-----
|
||
|
|
|
||
|
|
- power-supply: display panels require power to be supplied. While several
|
||
|
|
panels need more than one power supply with panel-specific constraints
|
||
|
|
governing the order and timings of the power supplies, in many cases a single
|
||
|
|
power supply is sufficient, either because the panel has a single power rail,
|
||
|
|
or because all its power rails can be driven by the same supply. In that case
|
||
|
|
the power-supply property specifies the supply powering the panel as a phandle
|
||
|
|
to a regulator.
|
||
|
|
|
||
|
|
Backlight
|
||
|
|
---------
|
||
|
|
|
||
|
|
Most display panels include a backlight. Some of them also include a backlight
|
||
|
|
controller exposed through a control bus such as I2C or DSI. Others expose
|
||
|
|
backlight control through GPIO, PWM or other signals connected to an external
|
||
|
|
backlight controller.
|
||
|
|
|
||
|
|
- backlight: For panels whose backlight is controlled by an external backlight
|
||
|
|
controller, this property contains a phandle that references the controller.
|