59 lines
1.7 KiB
Plaintext
59 lines
1.7 KiB
Plaintext
|
* Samsung Exynos 5440 PCIe interface
|
||
|
|
|
||
|
|
This PCIe host controller is based on the Synopsys DesignWare PCIe IP
|
||
|
|
and thus inherits all the common properties defined in designware-pcie.txt.
|
||
|
|
|
||
|
|
Required properties:
|
||
|
|
- compatible: "samsung,exynos5440-pcie"
|
||
|
|
- reg: base addresses and lengths of the PCIe controller,
|
||
|
|
- reg-names : First name should be set to "elbi".
|
||
|
|
And use the "config" instead of getting the configuration address space
|
||
|
|
from "ranges".
|
||
|
|
NOTE: When using the "config" property, reg-names must be set.
|
||
|
|
- interrupts: A list of interrupt outputs for level interrupt,
|
||
|
|
pulse interrupt, special interrupt.
|
||
|
|
- phys: From PHY binding. Phandle for the generic PHY.
|
||
|
|
Refer to Documentation/devicetree/bindings/phy/samsung-phy.txt
|
||
|
|
|
||
|
|
For other common properties, refer to
|
||
|
|
Documentation/devicetree/bindings/pci/designware-pcie.txt
|
||
|
|
|
||
|
|
Example:
|
||
|
|
|
||
|
|
SoC-specific DT Entry (with using PHY framework):
|
||
|
|
|
||
|
|
pcie_phy0: pcie-phy@270000 {
|
||
|
|
...
|
||
|
|
reg = <0x270000 0x1000>, <0x271000 0x40>;
|
||
|
|
reg-names = "phy", "block";
|
||
|
|
...
|
||
|
|
};
|
||
|
|
|
||
|
|
pcie@290000 {
|
||
|
|
compatible = "samsung,exynos5440-pcie", "snps,dw-pcie";
|
||
|
|
reg = <0x290000 0x1000>, <0x40000000 0x1000>;
|
||
|
|
reg-names = "elbi", "config";
|
||
|
|
clocks = <&clock 28>, <&clock 27>;
|
||
|
|
clock-names = "pcie", "pcie_bus";
|
||
|
|
#address-cells = <3>;
|
||
|
|
#size-cells = <2>;
|
||
|
|
device_type = "pci";
|
||
|
|
phys = <&pcie_phy0>;
|
||
|
|
ranges = <0x81000000 0 0 0x60001000 0 0x00010000
|
||
|
|
0x82000000 0 0x60011000 0x60011000 0 0x1ffef000>;
|
||
|
|
#interrupt-cells = <1>;
|
||
|
|
interrupt-map-mask = <0 0 0 0>;
|
||
|
|
interrupt-map = <0 0 0 0 &gic GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
|
||
|
|
num-lanes = <4>;
|
||
|
|
};
|
||
|
|
|
||
|
|
Board-specific DT Entry:
|
||
|
|
|
||
|
|
pcie@290000 {
|
||
|
|
reset-gpio = <&pin_ctrl 5 0>;
|
||
|
|
};
|
||
|
|
|
||
|
|
pcie@2a0000 {
|
||
|
|
reset-gpio = <&pin_ctrl 22 0>;
|
||
|
|
};
|