102 lines
3.3 KiB
Plaintext
102 lines
3.3 KiB
Plaintext
|
Qualcomm IPQ8064 TLMM block
|
||
|
|
|
||
|
|
Required properties:
|
||
|
|
- compatible: "qcom,ipq8064-pinctrl"
|
||
|
|
- reg: Should be the base address and length of the TLMM block.
|
||
|
|
- interrupts: Should be the parent IRQ of the TLMM block.
|
||
|
|
- interrupt-controller: Marks the device node as an interrupt controller.
|
||
|
|
- #interrupt-cells: Should be two.
|
||
|
|
- gpio-controller: Marks the device node as a GPIO controller.
|
||
|
|
- #gpio-cells : Should be two.
|
||
|
|
The first cell is the gpio pin number and the
|
||
|
|
second cell is used for optional parameters.
|
||
|
|
- gpio-ranges: see ../gpio/gpio.txt
|
||
|
|
|
||
|
|
Optional properties:
|
||
|
|
|
||
|
|
- gpio-reserved-ranges: see ../gpio/gpio.txt
|
||
|
|
|
||
|
|
Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
|
||
|
|
a general description of GPIO and interrupt bindings.
|
||
|
|
|
||
|
|
Please refer to pinctrl-bindings.txt in this directory for details of the
|
||
|
|
common pinctrl bindings used by client devices, including the meaning of the
|
||
|
|
phrase "pin configuration node".
|
||
|
|
|
||
|
|
Qualcomm's pin configuration nodes act as a container for an arbitrary number of
|
||
|
|
subnodes. Each of these subnodes represents some desired configuration for a
|
||
|
|
pin, a group, or a list of pins or groups. This configuration can include the
|
||
|
|
mux function to select on those pin(s)/group(s), and various pin configuration
|
||
|
|
parameters, such as pull-up, drive strength, etc.
|
||
|
|
|
||
|
|
The name of each subnode is not important; all subnodes should be enumerated
|
||
|
|
and processed purely based on their content.
|
||
|
|
|
||
|
|
Each subnode only affects those parameters that are explicitly listed. In
|
||
|
|
other words, a subnode that lists a mux function but no pin configuration
|
||
|
|
parameters implies no information about any pin configuration parameters.
|
||
|
|
Similarly, a pin subnode that describes a pullup parameter implies no
|
||
|
|
information about e.g. the mux function.
|
||
|
|
|
||
|
|
|
||
|
|
The following generic properties as defined in pinctrl-bindings.txt are valid
|
||
|
|
to specify in a pin configuration subnode:
|
||
|
|
|
||
|
|
pins, function, bias-disable, bias-pull-down, bias-pull,up, drive-strength,
|
||
|
|
output-low, output-high.
|
||
|
|
|
||
|
|
Non-empty subnodes must specify the 'pins' property.
|
||
|
|
|
||
|
|
Valid values for qcom,pins are:
|
||
|
|
gpio0-gpio68
|
||
|
|
Supports mux, bias, and drive-strength
|
||
|
|
|
||
|
|
sdc3_clk, sdc3_cmd, sdc3_data
|
||
|
|
Supports bias and drive-strength
|
||
|
|
|
||
|
|
|
||
|
|
Valid values for function are:
|
||
|
|
mdio, mi2s, pdm, ssbi, spmi, audio_pcm, gpio, gsbi1, gsbi2, gsbi4, gsbi5,
|
||
|
|
gsbi5_spi_cs1, gsbi5_spi_cs2, gsbi5_spi_cs3, gsbi6, gsbi7, nss_spi, sdc1,
|
||
|
|
spdif, nand, tsif1, tsif2, usb_fs_n, usb_fs, usb2_hsic, rgmii2, sata,
|
||
|
|
pcie1_rst, pcie1_prsnt, pcie1_pwren_n, pcie1_pwren, pcie1_pwrflt,
|
||
|
|
pcie1_clk_req, pcie2_rst, pcie2_prsnt, pcie2_pwren_n, pcie2_pwren,
|
||
|
|
pcie2_pwrflt, pcie2_clk_req, pcie3_rst, pcie3_prsnt, pcie3_pwren_n,
|
||
|
|
pcie3_pwren, pcie3_pwrflt, pcie3_clk_req, ps_hold
|
||
|
|
|
||
|
|
Example:
|
||
|
|
|
||
|
|
pinmux: pinctrl@800000 {
|
||
|
|
compatible = "qcom,ipq8064-pinctrl";
|
||
|
|
reg = <0x800000 0x4000>;
|
||
|
|
|
||
|
|
gpio-controller;
|
||
|
|
#gpio-cells = <2>;
|
||
|
|
gpio-ranges = <&pinmux 0 0 69>;
|
||
|
|
interrupt-controller;
|
||
|
|
#interrupt-cells = <2>;
|
||
|
|
interrupts = <0 32 0x4>;
|
||
|
|
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&gsbi5_uart_default>;
|
||
|
|
|
||
|
|
gsbi5_uart_default: gsbi5_uart_default {
|
||
|
|
mux {
|
||
|
|
pins = "gpio18", "gpio19";
|
||
|
|
function = "gsbi5";
|
||
|
|
};
|
||
|
|
|
||
|
|
tx {
|
||
|
|
pins = "gpio18";
|
||
|
|
drive-strength = <4>;
|
||
|
|
bias-disable;
|
||
|
|
};
|
||
|
|
|
||
|
|
rx {
|
||
|
|
pins = "gpio19";
|
||
|
|
drive-strength = <2>;
|
||
|
|
bias-pull-up;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
};
|