573 lines
15 KiB
C
573 lines
15 KiB
C
|
// SPDX-License-Identifier: GPL-2.0
|
||
|
/*
|
||
|
* This file is part of STM32 ADC driver
|
||
|
*
|
||
|
* Copyright (C) 2016, STMicroelectronics - All Rights Reserved
|
||
|
* Author: Fabrice Gasnier <fabrice.gasnier@st.com>.
|
||
|
*
|
||
|
* Inspired from: fsl-imx25-tsadc
|
||
|
*
|
||
|
*/
|
||
|
|
||
|
#include <linux/clk.h>
|
||
|
#include <linux/interrupt.h>
|
||
|
#include <linux/irqchip/chained_irq.h>
|
||
|
#include <linux/irqdesc.h>
|
||
|
#include <linux/irqdomain.h>
|
||
|
#include <linux/module.h>
|
||
|
#include <linux/of_device.h>
|
||
|
#include <linux/regulator/consumer.h>
|
||
|
#include <linux/slab.h>
|
||
|
|
||
|
#include "stm32-adc-core.h"
|
||
|
|
||
|
/**
|
||
|
* stm32_adc_common_regs - stm32 common registers, compatible dependent data
|
||
|
* @csr: common status register offset
|
||
|
* @eoc1: adc1 end of conversion flag in @csr
|
||
|
* @eoc2: adc2 end of conversion flag in @csr
|
||
|
* @eoc3: adc3 end of conversion flag in @csr
|
||
|
* @ier: interrupt enable register offset for each adc
|
||
|
* @eocie_msk: end of conversion interrupt enable mask in @ier
|
||
|
*/
|
||
|
struct stm32_adc_common_regs {
|
||
|
u32 csr;
|
||
|
u32 eoc1_msk;
|
||
|
u32 eoc2_msk;
|
||
|
u32 eoc3_msk;
|
||
|
u32 ier;
|
||
|
u32 eocie_msk;
|
||
|
};
|
||
|
|
||
|
struct stm32_adc_priv;
|
||
|
|
||
|
/**
|
||
|
* stm32_adc_priv_cfg - stm32 core compatible configuration data
|
||
|
* @regs: common registers for all instances
|
||
|
* @clk_sel: clock selection routine
|
||
|
* @max_clk_rate_hz: maximum analog clock rate (Hz, from datasheet)
|
||
|
*/
|
||
|
struct stm32_adc_priv_cfg {
|
||
|
const struct stm32_adc_common_regs *regs;
|
||
|
int (*clk_sel)(struct platform_device *, struct stm32_adc_priv *);
|
||
|
u32 max_clk_rate_hz;
|
||
|
};
|
||
|
|
||
|
/**
|
||
|
* struct stm32_adc_priv - stm32 ADC core private data
|
||
|
* @irq: irq(s) for ADC block
|
||
|
* @domain: irq domain reference
|
||
|
* @aclk: clock reference for the analog circuitry
|
||
|
* @bclk: bus clock common for all ADCs, depends on part used
|
||
|
* @vref: regulator reference
|
||
|
* @cfg: compatible configuration data
|
||
|
* @common: common data for all ADC instances
|
||
|
*/
|
||
|
struct stm32_adc_priv {
|
||
|
int irq[STM32_ADC_MAX_ADCS];
|
||
|
struct irq_domain *domain;
|
||
|
struct clk *aclk;
|
||
|
struct clk *bclk;
|
||
|
struct regulator *vref;
|
||
|
const struct stm32_adc_priv_cfg *cfg;
|
||
|
struct stm32_adc_common common;
|
||
|
};
|
||
|
|
||
|
static struct stm32_adc_priv *to_stm32_adc_priv(struct stm32_adc_common *com)
|
||
|
{
|
||
|
return container_of(com, struct stm32_adc_priv, common);
|
||
|
}
|
||
|
|
||
|
/* STM32F4 ADC internal common clock prescaler division ratios */
|
||
|
static int stm32f4_pclk_div[] = {2, 4, 6, 8};
|
||
|
|
||
|
/**
|
||
|
* stm32f4_adc_clk_sel() - Select stm32f4 ADC common clock prescaler
|
||
|
* @priv: stm32 ADC core private data
|
||
|
* Select clock prescaler used for analog conversions, before using ADC.
|
||
|
*/
|
||
|
static int stm32f4_adc_clk_sel(struct platform_device *pdev,
|
||
|
struct stm32_adc_priv *priv)
|
||
|
{
|
||
|
unsigned long rate;
|
||
|
u32 val;
|
||
|
int i;
|
||
|
|
||
|
/* stm32f4 has one clk input for analog (mandatory), enforce it here */
|
||
|
if (!priv->aclk) {
|
||
|
dev_err(&pdev->dev, "No 'adc' clock found\n");
|
||
|
return -ENOENT;
|
||
|
}
|
||
|
|
||
|
rate = clk_get_rate(priv->aclk);
|
||
|
if (!rate) {
|
||
|
dev_err(&pdev->dev, "Invalid clock rate: 0\n");
|
||
|
return -EINVAL;
|
||
|
}
|
||
|
|
||
|
for (i = 0; i < ARRAY_SIZE(stm32f4_pclk_div); i++) {
|
||
|
if ((rate / stm32f4_pclk_div[i]) <= priv->cfg->max_clk_rate_hz)
|
||
|
break;
|
||
|
}
|
||
|
if (i >= ARRAY_SIZE(stm32f4_pclk_div)) {
|
||
|
dev_err(&pdev->dev, "adc clk selection failed\n");
|
||
|
return -EINVAL;
|
||
|
}
|
||
|
|
||
|
priv->common.rate = rate / stm32f4_pclk_div[i];
|
||
|
val = readl_relaxed(priv->common.base + STM32F4_ADC_CCR);
|
||
|
val &= ~STM32F4_ADC_ADCPRE_MASK;
|
||
|
val |= i << STM32F4_ADC_ADCPRE_SHIFT;
|
||
|
writel_relaxed(val, priv->common.base + STM32F4_ADC_CCR);
|
||
|
|
||
|
dev_dbg(&pdev->dev, "Using analog clock source at %ld kHz\n",
|
||
|
priv->common.rate / 1000);
|
||
|
|
||
|
return 0;
|
||
|
}
|
||
|
|
||
|
/**
|
||
|
* struct stm32h7_adc_ck_spec - specification for stm32h7 adc clock
|
||
|
* @ckmode: ADC clock mode, Async or sync with prescaler.
|
||
|
* @presc: prescaler bitfield for async clock mode
|
||
|
* @div: prescaler division ratio
|
||
|
*/
|
||
|
struct stm32h7_adc_ck_spec {
|
||
|
u32 ckmode;
|
||
|
u32 presc;
|
||
|
int div;
|
||
|
};
|
||
|
|
||
|
static const struct stm32h7_adc_ck_spec stm32h7_adc_ckmodes_spec[] = {
|
||
|
/* 00: CK_ADC[1..3]: Asynchronous clock modes */
|
||
|
{ 0, 0, 1 },
|
||
|
{ 0, 1, 2 },
|
||
|
{ 0, 2, 4 },
|
||
|
{ 0, 3, 6 },
|
||
|
{ 0, 4, 8 },
|
||
|
{ 0, 5, 10 },
|
||
|
{ 0, 6, 12 },
|
||
|
{ 0, 7, 16 },
|
||
|
{ 0, 8, 32 },
|
||
|
{ 0, 9, 64 },
|
||
|
{ 0, 10, 128 },
|
||
|
{ 0, 11, 256 },
|
||
|
/* HCLK used: Synchronous clock modes (1, 2 or 4 prescaler) */
|
||
|
{ 1, 0, 1 },
|
||
|
{ 2, 0, 2 },
|
||
|
{ 3, 0, 4 },
|
||
|
};
|
||
|
|
||
|
static int stm32h7_adc_clk_sel(struct platform_device *pdev,
|
||
|
struct stm32_adc_priv *priv)
|
||
|
{
|
||
|
u32 ckmode, presc, val;
|
||
|
unsigned long rate;
|
||
|
int i, div;
|
||
|
|
||
|
/* stm32h7 bus clock is common for all ADC instances (mandatory) */
|
||
|
if (!priv->bclk) {
|
||
|
dev_err(&pdev->dev, "No 'bus' clock found\n");
|
||
|
return -ENOENT;
|
||
|
}
|
||
|
|
||
|
/*
|
||
|
* stm32h7 can use either 'bus' or 'adc' clock for analog circuitry.
|
||
|
* So, choice is to have bus clock mandatory and adc clock optional.
|
||
|
* If optional 'adc' clock has been found, then try to use it first.
|
||
|
*/
|
||
|
if (priv->aclk) {
|
||
|
/*
|
||
|
* Asynchronous clock modes (e.g. ckmode == 0)
|
||
|
* From spec: PLL output musn't exceed max rate
|
||
|
*/
|
||
|
rate = clk_get_rate(priv->aclk);
|
||
|
if (!rate) {
|
||
|
dev_err(&pdev->dev, "Invalid adc clock rate: 0\n");
|
||
|
return -EINVAL;
|
||
|
}
|
||
|
|
||
|
for (i = 0; i < ARRAY_SIZE(stm32h7_adc_ckmodes_spec); i++) {
|
||
|
ckmode = stm32h7_adc_ckmodes_spec[i].ckmode;
|
||
|
presc = stm32h7_adc_ckmodes_spec[i].presc;
|
||
|
div = stm32h7_adc_ckmodes_spec[i].div;
|
||
|
|
||
|
if (ckmode)
|
||
|
continue;
|
||
|
|
||
|
if ((rate / div) <= priv->cfg->max_clk_rate_hz)
|
||
|
goto out;
|
||
|
}
|
||
|
}
|
||
|
|
||
|
/* Synchronous clock modes (e.g. ckmode is 1, 2 or 3) */
|
||
|
rate = clk_get_rate(priv->bclk);
|
||
|
if (!rate) {
|
||
|
dev_err(&pdev->dev, "Invalid bus clock rate: 0\n");
|
||
|
return -EINVAL;
|
||
|
}
|
||
|
|
||
|
for (i = 0; i < ARRAY_SIZE(stm32h7_adc_ckmodes_spec); i++) {
|
||
|
ckmode = stm32h7_adc_ckmodes_spec[i].ckmode;
|
||
|
presc = stm32h7_adc_ckmodes_spec[i].presc;
|
||
|
div = stm32h7_adc_ckmodes_spec[i].div;
|
||
|
|
||
|
if (!ckmode)
|
||
|
continue;
|
||
|
|
||
|
if ((rate / div) <= priv->cfg->max_clk_rate_hz)
|
||
|
goto out;
|
||
|
}
|
||
|
|
||
|
dev_err(&pdev->dev, "adc clk selection failed\n");
|
||
|
return -EINVAL;
|
||
|
|
||
|
out:
|
||
|
/* rate used later by each ADC instance to control BOOST mode */
|
||
|
priv->common.rate = rate / div;
|
||
|
|
||
|
/* Set common clock mode and prescaler */
|
||
|
val = readl_relaxed(priv->common.base + STM32H7_ADC_CCR);
|
||
|
val &= ~(STM32H7_CKMODE_MASK | STM32H7_PRESC_MASK);
|
||
|
val |= ckmode << STM32H7_CKMODE_SHIFT;
|
||
|
val |= presc << STM32H7_PRESC_SHIFT;
|
||
|
writel_relaxed(val, priv->common.base + STM32H7_ADC_CCR);
|
||
|
|
||
|
dev_dbg(&pdev->dev, "Using %s clock/%d source at %ld kHz\n",
|
||
|
ckmode ? "bus" : "adc", div, priv->common.rate / 1000);
|
||
|
|
||
|
return 0;
|
||
|
}
|
||
|
|
||
|
/* STM32F4 common registers definitions */
|
||
|
static const struct stm32_adc_common_regs stm32f4_adc_common_regs = {
|
||
|
.csr = STM32F4_ADC_CSR,
|
||
|
.eoc1_msk = STM32F4_EOC1,
|
||
|
.eoc2_msk = STM32F4_EOC2,
|
||
|
.eoc3_msk = STM32F4_EOC3,
|
||
|
.ier = STM32F4_ADC_CR1,
|
||
|
.eocie_msk = STM32F4_EOCIE,
|
||
|
};
|
||
|
|
||
|
/* STM32H7 common registers definitions */
|
||
|
static const struct stm32_adc_common_regs stm32h7_adc_common_regs = {
|
||
|
.csr = STM32H7_ADC_CSR,
|
||
|
.eoc1_msk = STM32H7_EOC_MST,
|
||
|
.eoc2_msk = STM32H7_EOC_SLV,
|
||
|
.ier = STM32H7_ADC_IER,
|
||
|
.eocie_msk = STM32H7_EOCIE,
|
||
|
};
|
||
|
|
||
|
static const unsigned int stm32_adc_offset[STM32_ADC_MAX_ADCS] = {
|
||
|
0, STM32_ADC_OFFSET, STM32_ADC_OFFSET * 2,
|
||
|
};
|
||
|
|
||
|
static unsigned int stm32_adc_eoc_enabled(struct stm32_adc_priv *priv,
|
||
|
unsigned int adc)
|
||
|
{
|
||
|
u32 ier, offset = stm32_adc_offset[adc];
|
||
|
|
||
|
ier = readl_relaxed(priv->common.base + offset + priv->cfg->regs->ier);
|
||
|
|
||
|
return ier & priv->cfg->regs->eocie_msk;
|
||
|
}
|
||
|
|
||
|
/* ADC common interrupt for all instances */
|
||
|
static void stm32_adc_irq_handler(struct irq_desc *desc)
|
||
|
{
|
||
|
struct stm32_adc_priv *priv = irq_desc_get_handler_data(desc);
|
||
|
struct irq_chip *chip = irq_desc_get_chip(desc);
|
||
|
u32 status;
|
||
|
|
||
|
chained_irq_enter(chip, desc);
|
||
|
status = readl_relaxed(priv->common.base + priv->cfg->regs->csr);
|
||
|
|
||
|
/*
|
||
|
* End of conversion may be handled by using IRQ or DMA. There may be a
|
||
|
* race here when two conversions complete at the same time on several
|
||
|
* ADCs. EOC may be read 'set' for several ADCs, with:
|
||
|
* - an ADC configured to use DMA (EOC triggers the DMA request, and
|
||
|
* is then automatically cleared by DR read in hardware)
|
||
|
* - an ADC configured to use IRQs (EOCIE bit is set. The handler must
|
||
|
* be called in this case)
|
||
|
* So both EOC status bit in CSR and EOCIE control bit must be checked
|
||
|
* before invoking the interrupt handler (e.g. call ISR only for
|
||
|
* IRQ-enabled ADCs).
|
||
|
*/
|
||
|
if (status & priv->cfg->regs->eoc1_msk &&
|
||
|
stm32_adc_eoc_enabled(priv, 0))
|
||
|
generic_handle_irq(irq_find_mapping(priv->domain, 0));
|
||
|
|
||
|
if (status & priv->cfg->regs->eoc2_msk &&
|
||
|
stm32_adc_eoc_enabled(priv, 1))
|
||
|
generic_handle_irq(irq_find_mapping(priv->domain, 1));
|
||
|
|
||
|
if (status & priv->cfg->regs->eoc3_msk &&
|
||
|
stm32_adc_eoc_enabled(priv, 2))
|
||
|
generic_handle_irq(irq_find_mapping(priv->domain, 2));
|
||
|
|
||
|
chained_irq_exit(chip, desc);
|
||
|
};
|
||
|
|
||
|
static int stm32_adc_domain_map(struct irq_domain *d, unsigned int irq,
|
||
|
irq_hw_number_t hwirq)
|
||
|
{
|
||
|
irq_set_chip_data(irq, d->host_data);
|
||
|
irq_set_chip_and_handler(irq, &dummy_irq_chip, handle_level_irq);
|
||
|
|
||
|
return 0;
|
||
|
}
|
||
|
|
||
|
static void stm32_adc_domain_unmap(struct irq_domain *d, unsigned int irq)
|
||
|
{
|
||
|
irq_set_chip_and_handler(irq, NULL, NULL);
|
||
|
irq_set_chip_data(irq, NULL);
|
||
|
}
|
||
|
|
||
|
static const struct irq_domain_ops stm32_adc_domain_ops = {
|
||
|
.map = stm32_adc_domain_map,
|
||
|
.unmap = stm32_adc_domain_unmap,
|
||
|
.xlate = irq_domain_xlate_onecell,
|
||
|
};
|
||
|
|
||
|
static int stm32_adc_irq_probe(struct platform_device *pdev,
|
||
|
struct stm32_adc_priv *priv)
|
||
|
{
|
||
|
struct device_node *np = pdev->dev.of_node;
|
||
|
unsigned int i;
|
||
|
|
||
|
for (i = 0; i < STM32_ADC_MAX_ADCS; i++) {
|
||
|
priv->irq[i] = platform_get_irq(pdev, i);
|
||
|
if (priv->irq[i] < 0) {
|
||
|
/*
|
||
|
* At least one interrupt must be provided, make others
|
||
|
* optional:
|
||
|
* - stm32f4/h7 shares a common interrupt.
|
||
|
* - stm32mp1, has one line per ADC (either for ADC1,
|
||
|
* ADC2 or both).
|
||
|
*/
|
||
|
if (i && priv->irq[i] == -ENXIO)
|
||
|
continue;
|
||
|
dev_err(&pdev->dev, "failed to get irq\n");
|
||
|
|
||
|
return priv->irq[i];
|
||
|
}
|
||
|
}
|
||
|
|
||
|
priv->domain = irq_domain_add_simple(np, STM32_ADC_MAX_ADCS, 0,
|
||
|
&stm32_adc_domain_ops,
|
||
|
priv);
|
||
|
if (!priv->domain) {
|
||
|
dev_err(&pdev->dev, "Failed to add irq domain\n");
|
||
|
return -ENOMEM;
|
||
|
}
|
||
|
|
||
|
for (i = 0; i < STM32_ADC_MAX_ADCS; i++) {
|
||
|
if (priv->irq[i] < 0)
|
||
|
continue;
|
||
|
irq_set_chained_handler(priv->irq[i], stm32_adc_irq_handler);
|
||
|
irq_set_handler_data(priv->irq[i], priv);
|
||
|
}
|
||
|
|
||
|
return 0;
|
||
|
}
|
||
|
|
||
|
static void stm32_adc_irq_remove(struct platform_device *pdev,
|
||
|
struct stm32_adc_priv *priv)
|
||
|
{
|
||
|
int hwirq;
|
||
|
unsigned int i;
|
||
|
|
||
|
for (hwirq = 0; hwirq < STM32_ADC_MAX_ADCS; hwirq++)
|
||
|
irq_dispose_mapping(irq_find_mapping(priv->domain, hwirq));
|
||
|
irq_domain_remove(priv->domain);
|
||
|
|
||
|
for (i = 0; i < STM32_ADC_MAX_ADCS; i++) {
|
||
|
if (priv->irq[i] < 0)
|
||
|
continue;
|
||
|
irq_set_chained_handler(priv->irq[i], NULL);
|
||
|
}
|
||
|
}
|
||
|
|
||
|
static int stm32_adc_probe(struct platform_device *pdev)
|
||
|
{
|
||
|
struct stm32_adc_priv *priv;
|
||
|
struct device *dev = &pdev->dev;
|
||
|
struct device_node *np = pdev->dev.of_node;
|
||
|
struct resource *res;
|
||
|
int ret;
|
||
|
|
||
|
if (!pdev->dev.of_node)
|
||
|
return -ENODEV;
|
||
|
|
||
|
priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
|
||
|
if (!priv)
|
||
|
return -ENOMEM;
|
||
|
|
||
|
priv->cfg = (const struct stm32_adc_priv_cfg *)
|
||
|
of_match_device(dev->driver->of_match_table, dev)->data;
|
||
|
|
||
|
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
|
||
|
priv->common.base = devm_ioremap_resource(&pdev->dev, res);
|
||
|
if (IS_ERR(priv->common.base))
|
||
|
return PTR_ERR(priv->common.base);
|
||
|
priv->common.phys_base = res->start;
|
||
|
|
||
|
priv->vref = devm_regulator_get(&pdev->dev, "vref");
|
||
|
if (IS_ERR(priv->vref)) {
|
||
|
ret = PTR_ERR(priv->vref);
|
||
|
dev_err(&pdev->dev, "vref get failed, %d\n", ret);
|
||
|
return ret;
|
||
|
}
|
||
|
|
||
|
ret = regulator_enable(priv->vref);
|
||
|
if (ret < 0) {
|
||
|
dev_err(&pdev->dev, "vref enable failed\n");
|
||
|
return ret;
|
||
|
}
|
||
|
|
||
|
ret = regulator_get_voltage(priv->vref);
|
||
|
if (ret < 0) {
|
||
|
dev_err(&pdev->dev, "vref get voltage failed, %d\n", ret);
|
||
|
goto err_regulator_disable;
|
||
|
}
|
||
|
priv->common.vref_mv = ret / 1000;
|
||
|
dev_dbg(&pdev->dev, "vref+=%dmV\n", priv->common.vref_mv);
|
||
|
|
||
|
priv->aclk = devm_clk_get(&pdev->dev, "adc");
|
||
|
if (IS_ERR(priv->aclk)) {
|
||
|
ret = PTR_ERR(priv->aclk);
|
||
|
if (ret == -ENOENT) {
|
||
|
priv->aclk = NULL;
|
||
|
} else {
|
||
|
dev_err(&pdev->dev, "Can't get 'adc' clock\n");
|
||
|
goto err_regulator_disable;
|
||
|
}
|
||
|
}
|
||
|
|
||
|
if (priv->aclk) {
|
||
|
ret = clk_prepare_enable(priv->aclk);
|
||
|
if (ret < 0) {
|
||
|
dev_err(&pdev->dev, "adc clk enable failed\n");
|
||
|
goto err_regulator_disable;
|
||
|
}
|
||
|
}
|
||
|
|
||
|
priv->bclk = devm_clk_get(&pdev->dev, "bus");
|
||
|
if (IS_ERR(priv->bclk)) {
|
||
|
ret = PTR_ERR(priv->bclk);
|
||
|
if (ret == -ENOENT) {
|
||
|
priv->bclk = NULL;
|
||
|
} else {
|
||
|
dev_err(&pdev->dev, "Can't get 'bus' clock\n");
|
||
|
goto err_aclk_disable;
|
||
|
}
|
||
|
}
|
||
|
|
||
|
if (priv->bclk) {
|
||
|
ret = clk_prepare_enable(priv->bclk);
|
||
|
if (ret < 0) {
|
||
|
dev_err(&pdev->dev, "adc clk enable failed\n");
|
||
|
goto err_aclk_disable;
|
||
|
}
|
||
|
}
|
||
|
|
||
|
ret = priv->cfg->clk_sel(pdev, priv);
|
||
|
if (ret < 0)
|
||
|
goto err_bclk_disable;
|
||
|
|
||
|
ret = stm32_adc_irq_probe(pdev, priv);
|
||
|
if (ret < 0)
|
||
|
goto err_bclk_disable;
|
||
|
|
||
|
platform_set_drvdata(pdev, &priv->common);
|
||
|
|
||
|
ret = of_platform_populate(np, NULL, NULL, &pdev->dev);
|
||
|
if (ret < 0) {
|
||
|
dev_err(&pdev->dev, "failed to populate DT children\n");
|
||
|
goto err_irq_remove;
|
||
|
}
|
||
|
|
||
|
return 0;
|
||
|
|
||
|
err_irq_remove:
|
||
|
stm32_adc_irq_remove(pdev, priv);
|
||
|
|
||
|
err_bclk_disable:
|
||
|
if (priv->bclk)
|
||
|
clk_disable_unprepare(priv->bclk);
|
||
|
|
||
|
err_aclk_disable:
|
||
|
if (priv->aclk)
|
||
|
clk_disable_unprepare(priv->aclk);
|
||
|
|
||
|
err_regulator_disable:
|
||
|
regulator_disable(priv->vref);
|
||
|
|
||
|
return ret;
|
||
|
}
|
||
|
|
||
|
static int stm32_adc_remove(struct platform_device *pdev)
|
||
|
{
|
||
|
struct stm32_adc_common *common = platform_get_drvdata(pdev);
|
||
|
struct stm32_adc_priv *priv = to_stm32_adc_priv(common);
|
||
|
|
||
|
of_platform_depopulate(&pdev->dev);
|
||
|
stm32_adc_irq_remove(pdev, priv);
|
||
|
if (priv->bclk)
|
||
|
clk_disable_unprepare(priv->bclk);
|
||
|
if (priv->aclk)
|
||
|
clk_disable_unprepare(priv->aclk);
|
||
|
regulator_disable(priv->vref);
|
||
|
|
||
|
return 0;
|
||
|
}
|
||
|
|
||
|
static const struct stm32_adc_priv_cfg stm32f4_adc_priv_cfg = {
|
||
|
.regs = &stm32f4_adc_common_regs,
|
||
|
.clk_sel = stm32f4_adc_clk_sel,
|
||
|
.max_clk_rate_hz = 36000000,
|
||
|
};
|
||
|
|
||
|
static const struct stm32_adc_priv_cfg stm32h7_adc_priv_cfg = {
|
||
|
.regs = &stm32h7_adc_common_regs,
|
||
|
.clk_sel = stm32h7_adc_clk_sel,
|
||
|
.max_clk_rate_hz = 36000000,
|
||
|
};
|
||
|
|
||
|
static const struct stm32_adc_priv_cfg stm32mp1_adc_priv_cfg = {
|
||
|
.regs = &stm32h7_adc_common_regs,
|
||
|
.clk_sel = stm32h7_adc_clk_sel,
|
||
|
.max_clk_rate_hz = 40000000,
|
||
|
};
|
||
|
|
||
|
static const struct of_device_id stm32_adc_of_match[] = {
|
||
|
{
|
||
|
.compatible = "st,stm32f4-adc-core",
|
||
|
.data = (void *)&stm32f4_adc_priv_cfg
|
||
|
}, {
|
||
|
.compatible = "st,stm32h7-adc-core",
|
||
|
.data = (void *)&stm32h7_adc_priv_cfg
|
||
|
}, {
|
||
|
.compatible = "st,stm32mp1-adc-core",
|
||
|
.data = (void *)&stm32mp1_adc_priv_cfg
|
||
|
}, {
|
||
|
},
|
||
|
};
|
||
|
MODULE_DEVICE_TABLE(of, stm32_adc_of_match);
|
||
|
|
||
|
static struct platform_driver stm32_adc_driver = {
|
||
|
.probe = stm32_adc_probe,
|
||
|
.remove = stm32_adc_remove,
|
||
|
.driver = {
|
||
|
.name = "stm32-adc-core",
|
||
|
.of_match_table = stm32_adc_of_match,
|
||
|
},
|
||
|
};
|
||
|
module_platform_driver(stm32_adc_driver);
|
||
|
|
||
|
MODULE_AUTHOR("Fabrice Gasnier <fabrice.gasnier@st.com>");
|
||
|
MODULE_DESCRIPTION("STMicroelectronics STM32 ADC core driver");
|
||
|
MODULE_LICENSE("GPL v2");
|
||
|
MODULE_ALIAS("platform:stm32-adc-core");
|