372 lines
8.7 KiB
C
372 lines
8.7 KiB
C
|
/*
|
||
|
|
* DSPG DBMD2 SPI interface driver
|
||
|
|
*
|
||
|
|
* Copyright (C) 2014 DSP Group
|
||
|
|
*
|
||
|
|
* This software is licensed under the terms of the GNU General Public
|
||
|
|
* License version 2, as published by the Free Software Foundation, and
|
||
|
|
* may be copied, distributed, and modified under those terms.
|
||
|
|
*
|
||
|
|
* This program is distributed in the hope that it will be useful,
|
||
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||
|
|
* GNU General Public License for more details.
|
||
|
|
*/
|
||
|
|
/* #define DEBUG */
|
||
|
|
#include <linux/kernel.h>
|
||
|
|
#include <linux/delay.h>
|
||
|
|
#include <linux/slab.h>
|
||
|
|
#include <linux/spi/spi.h>
|
||
|
|
#include <linux/of_gpio.h>
|
||
|
|
#include <linux/module.h>
|
||
|
|
#include <linux/mutex.h>
|
||
|
|
#include <linux/clk.h>
|
||
|
|
#include <linux/of.h>
|
||
|
|
#include <linux/firmware.h>
|
||
|
|
|
||
|
|
#include "dbmdx-interface.h"
|
||
|
|
#include "dbmdx-va-regmap.h"
|
||
|
|
#include "dbmdx-vqe-regmap.h"
|
||
|
|
#include "dbmdx-spi.h"
|
||
|
|
|
||
|
|
#define DBMD2_MAX_SPI_BOOT_SPEED 8000000
|
||
|
|
|
||
|
|
static const u8 clr_crc[] = {0x5A, 0x03, 0x52, 0x0a, 0x00,
|
||
|
|
0x00, 0x00, 0x00, 0x00, 0x00};
|
||
|
|
static const u8 chng_pll_cmd[] = {0x5A, 0x13,
|
||
|
|
0x3D, 0x10, 0x00, 0x00,
|
||
|
|
0x00, 0x16, 0x00, 0x10,
|
||
|
|
0xFF, 0xF1, 0x3F, 0x00};
|
||
|
|
|
||
|
|
static int dbmd2_spi_boot(const void *fw_data, size_t fw_size,
|
||
|
|
struct dbmdx_private *p, const void *checksum,
|
||
|
|
size_t chksum_len, int load_fw)
|
||
|
|
{
|
||
|
|
int retry = RETRY_COUNT;
|
||
|
|
int ret = 0;
|
||
|
|
ssize_t send_bytes;
|
||
|
|
struct dbmdx_spi_private *spi_p =
|
||
|
|
(struct dbmdx_spi_private *)p->chip->pdata;
|
||
|
|
struct spi_device *spi = spi_p->client;
|
||
|
|
u8 sbl_spi[] = {
|
||
|
|
0x5A, 0x04, 0x4c, 0x00, 0x00,
|
||
|
|
0x03, 0x11, 0x55, 0x05, 0x00};
|
||
|
|
|
||
|
|
|
||
|
|
dev_dbg(spi_p->dev, "%s\n", __func__);
|
||
|
|
|
||
|
|
do {
|
||
|
|
|
||
|
|
if (p->active_fw == DBMDX_FW_PRE_BOOT) {
|
||
|
|
if (!(p->boot_mode & DBMDX_BOOT_MODE_RESET_DISABLED)) {
|
||
|
|
/* reset DBMD2 chip */
|
||
|
|
p->reset_sequence(p);
|
||
|
|
} else {
|
||
|
|
/* If failed and reset is disabled, break */
|
||
|
|
if (retry != RETRY_COUNT) {
|
||
|
|
retry = -1;
|
||
|
|
break;
|
||
|
|
}
|
||
|
|
}
|
||
|
|
|
||
|
|
/* delay before sending commands */
|
||
|
|
if (p->clk_get_rate(p, DBMDX_CLK_MASTER) <= 32768)
|
||
|
|
msleep(DBMDX_MSLEEP_SPI_D2_AFTER_RESET_32K);
|
||
|
|
else
|
||
|
|
usleep_range(DBMDX_USLEEP_SPI_D2_AFTER_RESET,
|
||
|
|
DBMDX_USLEEP_SPI_D2_AFTER_RESET + 5000);
|
||
|
|
|
||
|
|
ret = spi_set_speed(p, DBMDX_VA_SPEED_MAX);
|
||
|
|
if (ret < 0) {
|
||
|
|
dev_err(spi_p->dev, "%s:failed %x\n",
|
||
|
|
__func__, ret);
|
||
|
|
continue;
|
||
|
|
}
|
||
|
|
|
||
|
|
if ((spi->max_speed_hz > DBMD2_MAX_SPI_BOOT_SPEED) &&
|
||
|
|
!(p->cur_boot_options &
|
||
|
|
DBMDX_BOOT_OPT_DONT_SET_PLL)) {
|
||
|
|
|
||
|
|
ret = spi_set_speed(p, DBMDX_VA_SPEED_NORMAL);
|
||
|
|
if (ret < 0) {
|
||
|
|
dev_err(spi_p->dev, "%s:failed %x\n",
|
||
|
|
__func__, ret);
|
||
|
|
continue;
|
||
|
|
}
|
||
|
|
|
||
|
|
/* send Change PLL clear command */
|
||
|
|
ret = send_spi_data(p, chng_pll_cmd,
|
||
|
|
sizeof(chng_pll_cmd));
|
||
|
|
if (ret != sizeof(chng_pll_cmd)) {
|
||
|
|
dev_err(p->dev,
|
||
|
|
"%s: failed to change PLL\n",
|
||
|
|
__func__);
|
||
|
|
continue;
|
||
|
|
}
|
||
|
|
msleep(DBMDX_MSLEEP_SPI_D2_AFTER_PLL_CHANGE);
|
||
|
|
|
||
|
|
ret = spi_set_speed(p, DBMDX_VA_SPEED_MAX);
|
||
|
|
if (ret < 0) {
|
||
|
|
dev_err(spi_p->dev, "%s:failed %x\n",
|
||
|
|
__func__, ret);
|
||
|
|
continue;
|
||
|
|
}
|
||
|
|
}
|
||
|
|
|
||
|
|
if (!(p->cur_boot_options &
|
||
|
|
DBMDX_BOOT_OPT_DONT_SENT_SBL)) {
|
||
|
|
/* send SBL */
|
||
|
|
send_bytes = send_spi_data(p, sbl_spi,
|
||
|
|
sizeof(sbl_spi));
|
||
|
|
if (send_bytes != sizeof(sbl_spi)) {
|
||
|
|
dev_err(p->dev,
|
||
|
|
"%s: -----------> load SBL error\n",
|
||
|
|
__func__);
|
||
|
|
continue;
|
||
|
|
}
|
||
|
|
usleep_range(DBMDX_USLEEP_SPI_D2_AFTER_SBL,
|
||
|
|
DBMDX_USLEEP_SPI_D2_AFTER_SBL + 1000);
|
||
|
|
}
|
||
|
|
/* verify chip id */
|
||
|
|
if (p->cur_boot_options &
|
||
|
|
DBMDX_BOOT_OPT_VERIFY_CHIP_ID) {
|
||
|
|
ret = spi_verify_chip_id(p);
|
||
|
|
if (ret < 0) {
|
||
|
|
dev_err(spi_p->dev,
|
||
|
|
"%s: couldn't verify chip id\n",
|
||
|
|
__func__);
|
||
|
|
continue;
|
||
|
|
}
|
||
|
|
}
|
||
|
|
|
||
|
|
if (!(p->cur_boot_options &
|
||
|
|
DBMDX_BOOT_OPT_DONT_CLR_CRC)) {
|
||
|
|
/* send CRC clear command */
|
||
|
|
ret = send_spi_data(p, clr_crc,
|
||
|
|
sizeof(clr_crc));
|
||
|
|
if (ret != sizeof(clr_crc)) {
|
||
|
|
dev_err(p->dev,
|
||
|
|
"%s: failed to clear CRC\n",
|
||
|
|
__func__);
|
||
|
|
continue;
|
||
|
|
}
|
||
|
|
}
|
||
|
|
} else {
|
||
|
|
/* delay before sending commands */
|
||
|
|
if (p->active_fw == DBMDX_FW_VQE)
|
||
|
|
ret = send_spi_cmd_vqe(p,
|
||
|
|
DBMDX_VQE_SET_SWITCH_TO_BOOT_CMD,
|
||
|
|
NULL);
|
||
|
|
else if (p->active_fw == DBMDX_FW_VA)
|
||
|
|
ret = send_spi_cmd_va(p,
|
||
|
|
DBMDX_VA_SWITCH_TO_BOOT,
|
||
|
|
NULL);
|
||
|
|
if (ret < 0) {
|
||
|
|
dev_err(p->dev,
|
||
|
|
"%s: failed to send 'Switch to BOOT' cmd\n",
|
||
|
|
__func__);
|
||
|
|
continue;
|
||
|
|
}
|
||
|
|
}
|
||
|
|
|
||
|
|
if (!load_fw)
|
||
|
|
break;
|
||
|
|
|
||
|
|
/* send firmware */
|
||
|
|
send_bytes = send_spi_data(p, fw_data, fw_size - 4);
|
||
|
|
if (send_bytes != fw_size - 4) {
|
||
|
|
dev_err(p->dev,
|
||
|
|
"%s: -----------> load firmware error\n",
|
||
|
|
__func__);
|
||
|
|
continue;
|
||
|
|
}
|
||
|
|
|
||
|
|
/* verify checksum */
|
||
|
|
if (checksum && !(p->cur_boot_options &
|
||
|
|
DBMDX_BOOT_OPT_DONT_VERIFY_CRC)) {
|
||
|
|
ret = spi_verify_boot_checksum(p, checksum, chksum_len);
|
||
|
|
if (ret < 0) {
|
||
|
|
dev_err(spi_p->dev,
|
||
|
|
"%s: could not verify checksum\n",
|
||
|
|
__func__);
|
||
|
|
continue;
|
||
|
|
}
|
||
|
|
}
|
||
|
|
dev_dbg(p->dev, "%s: ---------> firmware loaded\n",
|
||
|
|
__func__);
|
||
|
|
break;
|
||
|
|
} while (--retry);
|
||
|
|
|
||
|
|
/* no retries left, failed to boot */
|
||
|
|
if (retry <= 0) {
|
||
|
|
dev_err(p->dev, "%s: failed to load firmware\n", __func__);
|
||
|
|
return -EIO;
|
||
|
|
}
|
||
|
|
|
||
|
|
if (!(p->cur_boot_options & DBMDX_BOOT_OPT_DONT_SEND_START_BOOT)) {
|
||
|
|
/* send boot command */
|
||
|
|
ret = send_spi_cmd_boot(p, DBMDX_FIRMWARE_BOOT);
|
||
|
|
if (ret < 0) {
|
||
|
|
dev_err(p->dev,
|
||
|
|
"%s: booting the firmware failed\n", __func__);
|
||
|
|
return -EIO;
|
||
|
|
}
|
||
|
|
}
|
||
|
|
|
||
|
|
ret = spi_set_speed(p, DBMDX_VA_SPEED_NORMAL);
|
||
|
|
if (ret < 0)
|
||
|
|
dev_err(spi_p->dev, "%s:failed %x\n", __func__, ret);
|
||
|
|
|
||
|
|
/* wait some time */
|
||
|
|
usleep_range(DBMDX_USLEEP_SPI_D2_AFTER_BOOT,
|
||
|
|
DBMDX_USLEEP_SPI_D2_AFTER_BOOT + 1000);
|
||
|
|
|
||
|
|
return 0;
|
||
|
|
}
|
||
|
|
|
||
|
|
#if IS_ENABLED(CONFIG_PM_SLEEP)
|
||
|
|
static int dbmdx_spi_suspend(struct device *dev)
|
||
|
|
{
|
||
|
|
struct chip_interface *ci = spi_get_drvdata(to_spi_device(dev));
|
||
|
|
struct dbmdx_spi_private *spi_p = (struct dbmdx_spi_private *)ci->pdata;
|
||
|
|
|
||
|
|
dev_dbg(dev, "%s\n", __func__);
|
||
|
|
|
||
|
|
spi_interface_suspend(spi_p);
|
||
|
|
|
||
|
|
return 0;
|
||
|
|
}
|
||
|
|
|
||
|
|
static int dbmdx_spi_resume(struct device *dev)
|
||
|
|
{
|
||
|
|
struct chip_interface *ci = spi_get_drvdata(to_spi_device(dev));
|
||
|
|
struct dbmdx_spi_private *spi_p = (struct dbmdx_spi_private *)ci->pdata;
|
||
|
|
|
||
|
|
dev_dbg(dev, "%s\n", __func__);
|
||
|
|
spi_interface_resume(spi_p);
|
||
|
|
|
||
|
|
return 0;
|
||
|
|
}
|
||
|
|
#else
|
||
|
|
#define dbmdx_spi_suspend NULL
|
||
|
|
#define dbmdx_spi_resume NULL
|
||
|
|
#endif /* CONFIG_PM_SLEEP */
|
||
|
|
|
||
|
|
#if IS_ENABLED(CONFIG_PM)
|
||
|
|
static int dbmdx_spi_runtime_suspend(struct device *dev)
|
||
|
|
{
|
||
|
|
struct chip_interface *ci = spi_get_drvdata(to_spi_device(dev));
|
||
|
|
struct dbmdx_spi_private *spi_p = (struct dbmdx_spi_private *)ci->pdata;
|
||
|
|
|
||
|
|
dev_dbg(dev, "%s\n", __func__);
|
||
|
|
|
||
|
|
spi_interface_suspend(spi_p);
|
||
|
|
|
||
|
|
return 0;
|
||
|
|
}
|
||
|
|
|
||
|
|
static int dbmdx_spi_runtime_resume(struct device *dev)
|
||
|
|
{
|
||
|
|
struct chip_interface *ci = spi_get_drvdata(to_spi_device(dev));
|
||
|
|
struct dbmdx_spi_private *spi_p = (struct dbmdx_spi_private *)ci->pdata;
|
||
|
|
|
||
|
|
dev_dbg(dev, "%s\n", __func__);
|
||
|
|
spi_interface_resume(spi_p);
|
||
|
|
|
||
|
|
return 0;
|
||
|
|
}
|
||
|
|
#else
|
||
|
|
#define dbmdx_spi_runtime_suspend NULL
|
||
|
|
#define dbmdx_spi_runtime_resume NULL
|
||
|
|
#endif /* CONFIG_PM */
|
||
|
|
|
||
|
|
static const struct dev_pm_ops dbmdx_spi_pm = {
|
||
|
|
SET_SYSTEM_SLEEP_PM_OPS(dbmdx_spi_suspend, dbmdx_spi_resume)
|
||
|
|
SET_RUNTIME_PM_OPS(dbmdx_spi_runtime_suspend,
|
||
|
|
dbmdx_spi_runtime_resume, NULL)
|
||
|
|
};
|
||
|
|
|
||
|
|
|
||
|
|
static int dbmd2_spi_probe(struct spi_device *client)
|
||
|
|
{
|
||
|
|
int rc;
|
||
|
|
struct dbmdx_spi_private *p;
|
||
|
|
struct chip_interface *ci;
|
||
|
|
|
||
|
|
rc = spi_common_probe(client);
|
||
|
|
|
||
|
|
if (rc < 0)
|
||
|
|
return rc;
|
||
|
|
|
||
|
|
ci = spi_get_drvdata(client);
|
||
|
|
p = (struct dbmdx_spi_private *)ci->pdata;
|
||
|
|
|
||
|
|
/* fill in chip interface functions */
|
||
|
|
p->chip.boot = dbmd2_spi_boot;
|
||
|
|
|
||
|
|
return rc;
|
||
|
|
}
|
||
|
|
|
||
|
|
|
||
|
|
static const struct of_device_id dbmd2_spi_of_match[] = {
|
||
|
|
{ .compatible = "dspg,dbmd2-spi", },
|
||
|
|
{},
|
||
|
|
};
|
||
|
|
#if IS_ENABLED(CONFIG_SND_SOC_DBMDX)
|
||
|
|
MODULE_DEVICE_TABLE(of, dbmd2_spi_of_match);
|
||
|
|
#endif
|
||
|
|
|
||
|
|
static const struct spi_device_id dbmd2_spi_id[] = {
|
||
|
|
{ "dbmdx-spi", 0 },
|
||
|
|
{ "dbmd2-spi", 0 },
|
||
|
|
{ }
|
||
|
|
};
|
||
|
|
MODULE_DEVICE_TABLE(spi, dbmd2_spi_id);
|
||
|
|
|
||
|
|
static struct spi_driver dbmd2_spi_driver = {
|
||
|
|
.driver = {
|
||
|
|
.name = "dbmd2-spi",
|
||
|
|
.bus = &spi_bus_type,
|
||
|
|
.owner = THIS_MODULE,
|
||
|
|
#if IS_ENABLED(CONFIG_OF)
|
||
|
|
.of_match_table = dbmd2_spi_of_match,
|
||
|
|
#endif
|
||
|
|
.pm = &dbmdx_spi_pm,
|
||
|
|
},
|
||
|
|
.probe = dbmd2_spi_probe,
|
||
|
|
.remove = spi_common_remove,
|
||
|
|
.id_table = dbmd2_spi_id,
|
||
|
|
};
|
||
|
|
|
||
|
|
#if (IS_ENABLED(CONFIG_SND_SOC_DBMDX) && !IS_MODULE(CONFIG_SND_SOC_DBMDX))
|
||
|
|
static int __init dbmd2_modinit(void)
|
||
|
|
{
|
||
|
|
return spi_register_driver(&dbmd2_spi_driver);
|
||
|
|
}
|
||
|
|
|
||
|
|
module_init(dbmd2_modinit);
|
||
|
|
|
||
|
|
static void __exit dbmd2_exit(void)
|
||
|
|
{
|
||
|
|
spi_unregister_driver(&dbmd2_spi_driver);
|
||
|
|
}
|
||
|
|
module_exit(dbmd2_exit);
|
||
|
|
#else
|
||
|
|
int dbmd2_spi_init_interface(void)
|
||
|
|
{
|
||
|
|
spi_register_driver(&dbmd2_spi_driver);
|
||
|
|
return 0;
|
||
|
|
}
|
||
|
|
|
||
|
|
void dbmd2_spi_deinit_interface(void)
|
||
|
|
{
|
||
|
|
spi_unregister_driver(&dbmd2_spi_driver);
|
||
|
|
}
|
||
|
|
|
||
|
|
int (*dbmdx_init_interface)(void) = &dbmd2_spi_init_interface;
|
||
|
|
void (*dbmdx_deinit_interface)(void) = &dbmd2_spi_deinit_interface;
|
||
|
|
#endif
|
||
|
|
|
||
|
|
MODULE_DESCRIPTION("DSPG DBMD2 spi interface driver");
|
||
|
|
MODULE_LICENSE("GPL");
|