94 lines
2.5 KiB
Plaintext
94 lines
2.5 KiB
Plaintext
|
Allwinner A31 DSI Encoder
|
||
|
|
=========================
|
||
|
|
|
||
|
|
The DSI pipeline consists of two separate blocks: the DSI controller
|
||
|
|
itself, and its associated D-PHY.
|
||
|
|
|
||
|
|
DSI Encoder
|
||
|
|
-----------
|
||
|
|
|
||
|
|
The DSI Encoder generates the DSI signal from the TCON's.
|
||
|
|
|
||
|
|
Required properties:
|
||
|
|
- compatible: value must be one of:
|
||
|
|
* allwinner,sun6i-a31-mipi-dsi
|
||
|
|
- reg: base address and size of memory-mapped region
|
||
|
|
- interrupts: interrupt associated to this IP
|
||
|
|
- clocks: phandles to the clocks feeding the DSI encoder
|
||
|
|
* bus: the DSI interface clock
|
||
|
|
* mod: the DSI module clock
|
||
|
|
- clock-names: the clock names mentioned above
|
||
|
|
- phys: phandle to the D-PHY
|
||
|
|
- phy-names: must be "dphy"
|
||
|
|
- resets: phandle to the reset controller driving the encoder
|
||
|
|
|
||
|
|
- ports: A ports node with endpoint definitions as defined in
|
||
|
|
Documentation/devicetree/bindings/media/video-interfaces.txt. The
|
||
|
|
first port should be the input endpoint, usually coming from the
|
||
|
|
associated TCON.
|
||
|
|
|
||
|
|
Any MIPI-DSI device attached to this should be described according to
|
||
|
|
the bindings defined in ../mipi-dsi-bus.txt
|
||
|
|
|
||
|
|
D-PHY
|
||
|
|
-----
|
||
|
|
|
||
|
|
Required properties:
|
||
|
|
- compatible: value must be one of:
|
||
|
|
* allwinner,sun6i-a31-mipi-dphy
|
||
|
|
- reg: base address and size of memory-mapped region
|
||
|
|
- clocks: phandles to the clocks feeding the DSI encoder
|
||
|
|
* bus: the DSI interface clock
|
||
|
|
* mod: the DSI module clock
|
||
|
|
- clock-names: the clock names mentioned above
|
||
|
|
- resets: phandle to the reset controller driving the encoder
|
||
|
|
|
||
|
|
Example:
|
||
|
|
|
||
|
|
dsi0: dsi@1ca0000 {
|
||
|
|
compatible = "allwinner,sun6i-a31-mipi-dsi";
|
||
|
|
reg = <0x01ca0000 0x1000>;
|
||
|
|
interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
|
||
|
|
clocks = <&ccu CLK_BUS_MIPI_DSI>,
|
||
|
|
<&ccu CLK_DSI_SCLK>;
|
||
|
|
clock-names = "bus", "mod";
|
||
|
|
resets = <&ccu RST_BUS_MIPI_DSI>;
|
||
|
|
phys = <&dphy0>;
|
||
|
|
phy-names = "dphy";
|
||
|
|
#address-cells = <1>;
|
||
|
|
#size-cells = <0>;
|
||
|
|
|
||
|
|
panel@0 {
|
||
|
|
compatible = "bananapi,lhr050h41", "ilitek,ili9881c";
|
||
|
|
reg = <0>;
|
||
|
|
power-gpios = <&pio 1 7 GPIO_ACTIVE_HIGH>; /* PB07 */
|
||
|
|
reset-gpios = <&r_pio 0 5 GPIO_ACTIVE_LOW>; /* PL05 */
|
||
|
|
backlight = <&pwm_bl>;
|
||
|
|
};
|
||
|
|
|
||
|
|
ports {
|
||
|
|
#address-cells = <1>;
|
||
|
|
#size-cells = <0>;
|
||
|
|
|
||
|
|
port@0 {
|
||
|
|
#address-cells = <1>;
|
||
|
|
#size-cells = <0>;
|
||
|
|
reg = <0>;
|
||
|
|
|
||
|
|
dsi0_in_tcon0: endpoint {
|
||
|
|
remote-endpoint = <&tcon0_out_dsi0>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
dphy0: d-phy@1ca1000 {
|
||
|
|
compatible = "allwinner,sun6i-a31-mipi-dphy";
|
||
|
|
reg = <0x01ca1000 0x1000>;
|
||
|
|
clocks = <&ccu CLK_BUS_MIPI_DSI>,
|
||
|
|
<&ccu CLK_DSI_DPHY>;
|
||
|
|
clock-names = "bus", "mod";
|
||
|
|
resets = <&ccu RST_BUS_MIPI_DSI>;
|
||
|
|
#phy-cells = <0>;
|
||
|
|
};
|