83 lines
2.2 KiB
Plaintext
83 lines
2.2 KiB
Plaintext
|
Renesas Capture Engine Unit (CEU)
|
||
|
|
----------------------------------------------
|
||
|
|
|
||
|
|
The Capture Engine Unit is the image capture interface found in the Renesas
|
||
|
|
SH Mobile, R-Mobile and RZ SoCs.
|
||
|
|
|
||
|
|
The interface supports a single parallel input with data bus width of 8 or 16
|
||
|
|
bits.
|
||
|
|
|
||
|
|
Required properties:
|
||
|
|
- compatible: Shall be one of the following values:
|
||
|
|
"renesas,r7s72100-ceu" for CEU units found in RZ/A1H and RZ/A1M SoCs
|
||
|
|
"renesas,r8a7740-ceu" for CEU units found in R-Mobile A1 R8A7740 SoCs
|
||
|
|
- reg: Registers address base and size.
|
||
|
|
- interrupts: The interrupt specifier.
|
||
|
|
|
||
|
|
The CEU supports a single parallel input and should contain a single 'port'
|
||
|
|
subnode with a single 'endpoint'. Connection to input devices are modeled
|
||
|
|
according to the video interfaces OF bindings specified in:
|
||
|
|
Documentation/devicetree/bindings/media/video-interfaces.txt
|
||
|
|
|
||
|
|
Optional endpoint properties applicable to parallel input bus described in
|
||
|
|
the above mentioned "video-interfaces.txt" file are supported.
|
||
|
|
|
||
|
|
- hsync-active: Active state of the HSYNC signal, 0/1 for LOW/HIGH respectively.
|
||
|
|
If property is not present, default is active high.
|
||
|
|
- vsync-active: Active state of the VSYNC signal, 0/1 for LOW/HIGH respectively.
|
||
|
|
If property is not present, default is active high.
|
||
|
|
|
||
|
|
Example:
|
||
|
|
|
||
|
|
The example describes the connection between the Capture Engine Unit and an
|
||
|
|
OV7670 image sensor connected to i2c1 interface.
|
||
|
|
|
||
|
|
ceu: ceu@e8210000 {
|
||
|
|
reg = <0xe8210000 0x209c>;
|
||
|
|
compatible = "renesas,r7s72100-ceu";
|
||
|
|
interrupts = <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>;
|
||
|
|
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&vio_pins>;
|
||
|
|
|
||
|
|
status = "okay";
|
||
|
|
|
||
|
|
port {
|
||
|
|
ceu_in: endpoint {
|
||
|
|
remote-endpoint = <&ov7670_out>;
|
||
|
|
|
||
|
|
hsync-active = <1>;
|
||
|
|
vsync-active = <0>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
i2c1: i2c@fcfee400 {
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&i2c1_pins>;
|
||
|
|
|
||
|
|
status = "okay";
|
||
|
|
|
||
|
|
clock-frequency = <100000>;
|
||
|
|
|
||
|
|
ov7670: camera@21 {
|
||
|
|
compatible = "ovti,ov7670";
|
||
|
|
reg = <0x21>;
|
||
|
|
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&vio_pins>;
|
||
|
|
|
||
|
|
reset-gpios = <&port3 11 GPIO_ACTIVE_LOW>;
|
||
|
|
powerdown-gpios = <&port3 12 GPIO_ACTIVE_HIGH>;
|
||
|
|
|
||
|
|
port {
|
||
|
|
ov7670_out: endpoint {
|
||
|
|
remote-endpoint = <&ceu_in>;
|
||
|
|
|
||
|
|
hsync-active = <1>;
|
||
|
|
vsync-active = <0>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
};
|
||
|
|
};
|