88 lines
2.5 KiB
Plaintext
88 lines
2.5 KiB
Plaintext
|
QCOM GSBI (General Serial Bus Interface) Driver
|
||
|
|
|
||
|
|
The GSBI controller is modeled as a node with zero or more child nodes, each
|
||
|
|
representing a serial sub-node device that is mux'd as part of the GSBI
|
||
|
|
configuration settings. The mode setting will govern the input/output mode of
|
||
|
|
the 4 GSBI IOs.
|
||
|
|
|
||
|
|
Required properties:
|
||
|
|
- compatible: Should contain "qcom,gsbi-v1.0.0"
|
||
|
|
- cell-index: Should contain the GSBI index
|
||
|
|
- reg: Address range for GSBI registers
|
||
|
|
- clocks: required clock
|
||
|
|
- clock-names: must contain "iface" entry
|
||
|
|
- qcom,mode : indicates MUX value for configuration of the serial interface.
|
||
|
|
Please reference dt-bindings/soc/qcom,gsbi.h for valid mux values.
|
||
|
|
|
||
|
|
Optional properties:
|
||
|
|
- qcom,crci : indicates CRCI MUX value for QUP CRCI ports. Please reference
|
||
|
|
dt-bindings/soc/qcom,gsbi.h for valid CRCI mux values.
|
||
|
|
- syscon-tcsr: indicates phandle of TCSR syscon node. Required if child uses
|
||
|
|
dma.
|
||
|
|
|
||
|
|
Required properties if child node exists:
|
||
|
|
- #address-cells: Must be 1
|
||
|
|
- #size-cells: Must be 1
|
||
|
|
- ranges: Must be present
|
||
|
|
|
||
|
|
Properties for children:
|
||
|
|
|
||
|
|
A GSBI controller node can contain 0 or more child nodes representing serial
|
||
|
|
devices. These serial devices can be a QCOM UART, I2C controller, spi
|
||
|
|
controller, or some combination of aforementioned devices.
|
||
|
|
|
||
|
|
See the following for child node definitions:
|
||
|
|
Documentation/devicetree/bindings/i2c/qcom,i2c-qup.txt
|
||
|
|
Documentation/devicetree/bindings/spi/qcom,spi-qup.txt
|
||
|
|
Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt
|
||
|
|
|
||
|
|
Example for APQ8064:
|
||
|
|
|
||
|
|
#include <dt-bindings/soc/qcom,gsbi.h>
|
||
|
|
|
||
|
|
gsbi4@16300000 {
|
||
|
|
compatible = "qcom,gsbi-v1.0.0";
|
||
|
|
cell-index = <4>;
|
||
|
|
reg = <0x16300000 0x100>;
|
||
|
|
clocks = <&gcc GSBI4_H_CLK>;
|
||
|
|
clock-names = "iface";
|
||
|
|
#address-cells = <1>;
|
||
|
|
#size-cells = <1>;
|
||
|
|
ranges;
|
||
|
|
qcom,mode = <GSBI_PROT_I2C_UART>;
|
||
|
|
qcom,crci = <GSBI_CRCI_QUP>;
|
||
|
|
|
||
|
|
syscon-tcsr = <&tcsr>;
|
||
|
|
|
||
|
|
/* child nodes go under here */
|
||
|
|
|
||
|
|
i2c_qup4: i2c@16380000 {
|
||
|
|
compatible = "qcom,i2c-qup-v1.1.1";
|
||
|
|
reg = <0x16380000 0x1000>;
|
||
|
|
interrupts = <0 153 0>;
|
||
|
|
|
||
|
|
clocks = <&gcc GSBI4_QUP_CLK>, <&gcc GSBI4_H_CLK>;
|
||
|
|
clock-names = "core", "iface";
|
||
|
|
|
||
|
|
clock-frequency = <200000>;
|
||
|
|
|
||
|
|
#address-cells = <1>;
|
||
|
|
#size-cells = <0>;
|
||
|
|
|
||
|
|
};
|
||
|
|
|
||
|
|
uart4: serial@16340000 {
|
||
|
|
compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
|
||
|
|
reg = <0x16340000 0x1000>,
|
||
|
|
<0x16300000 0x1000>;
|
||
|
|
interrupts = <0 152 0x0>;
|
||
|
|
clocks = <&gcc GSBI4_UART_CLK>, <&gcc GSBI4_H_CLK>;
|
||
|
|
clock-names = "core", "iface";
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
tcsr: syscon@1a400000 {
|
||
|
|
compatible = "qcom,apq8064-tcsr", "syscon";
|
||
|
|
reg = <0x1a400000 0x100>;
|
||
|
|
};
|