58 lines
2 KiB
Plaintext
58 lines
2 KiB
Plaintext
|
MediaTek musb DRD/OTG controller
|
||
|
|
-------------------------------------------
|
||
|
|
|
||
|
|
Required properties:
|
||
|
|
- compatible : should be one of:
|
||
|
|
"mediatek,mt2701-musb"
|
||
|
|
...
|
||
|
|
followed by "mediatek,mtk-musb"
|
||
|
|
- reg : specifies physical base address and size of
|
||
|
|
the registers
|
||
|
|
- interrupts : interrupt used by musb controller
|
||
|
|
- interrupt-names : must be "mc"
|
||
|
|
- phys : PHY specifier for the OTG phy
|
||
|
|
- dr_mode : should be one of "host", "peripheral" or "otg",
|
||
|
|
refer to usb/generic.txt
|
||
|
|
- clocks : a list of phandle + clock-specifier pairs, one for
|
||
|
|
each entry in clock-names
|
||
|
|
- clock-names : must contain "main", "mcu", "univpll"
|
||
|
|
for clocks of controller
|
||
|
|
|
||
|
|
Optional properties:
|
||
|
|
- power-domains : a phandle to USB power domain node to control USB's
|
||
|
|
MTCMOS
|
||
|
|
|
||
|
|
Required child nodes:
|
||
|
|
usb connector node as defined in bindings/connector/usb-connector.txt
|
||
|
|
Optional properties:
|
||
|
|
- id-gpios : input GPIO for USB ID pin.
|
||
|
|
- vbus-gpios : input GPIO for USB VBUS pin.
|
||
|
|
- vbus-supply : reference to the VBUS regulator, needed when supports
|
||
|
|
dual-role mode
|
||
|
|
- usb-role-switch : use USB Role Switch to support dual-role switch, see
|
||
|
|
usb/generic.txt.
|
||
|
|
|
||
|
|
Example:
|
||
|
|
|
||
|
|
usb2: usb@11200000 {
|
||
|
|
compatible = "mediatek,mt2701-musb",
|
||
|
|
"mediatek,mtk-musb";
|
||
|
|
reg = <0 0x11200000 0 0x1000>;
|
||
|
|
interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>;
|
||
|
|
interrupt-names = "mc";
|
||
|
|
phys = <&u2port2 PHY_TYPE_USB2>;
|
||
|
|
dr_mode = "otg";
|
||
|
|
clocks = <&pericfg CLK_PERI_USB0>,
|
||
|
|
<&pericfg CLK_PERI_USB0_MCU>,
|
||
|
|
<&pericfg CLK_PERI_USB_SLV>;
|
||
|
|
clock-names = "main","mcu","univpll";
|
||
|
|
power-domains = <&scpsys MT2701_POWER_DOMAIN_IFR_MSC>;
|
||
|
|
usb-role-switch;
|
||
|
|
connector{
|
||
|
|
compatible = "gpio-usb-b-connector", "usb-b-connector";
|
||
|
|
type = "micro";
|
||
|
|
id-gpios = <&pio 44 GPIO_ACTIVE_HIGH>;
|
||
|
|
vbus-supply = <&usb_vbus>;
|
||
|
|
};
|
||
|
|
};
|