60 lines
2 KiB
Plaintext
60 lines
2 KiB
Plaintext
|
STMicroelectronics STM32 SPI Controller
|
||
|
|
|
||
|
|
The STM32 SPI controller is used to communicate with external devices using
|
||
|
|
the Serial Peripheral Interface. It supports full-duplex, half-duplex and
|
||
|
|
simplex synchronous serial communication with external devices. It supports
|
||
|
|
from 4 to 32-bit data size. Although it can be configured as master or slave,
|
||
|
|
only master is supported by the driver.
|
||
|
|
|
||
|
|
Required properties:
|
||
|
|
- compatible: Must be "st,stm32h7-spi".
|
||
|
|
- reg: Offset and length of the device's register set.
|
||
|
|
- interrupts: Must contain the interrupt id.
|
||
|
|
- clocks: Must contain an entry for spiclk (which feeds the internal clock
|
||
|
|
generator).
|
||
|
|
- #address-cells: Number of cells required to define a chip select address.
|
||
|
|
- #size-cells: Should be zero.
|
||
|
|
|
||
|
|
Optional properties:
|
||
|
|
- resets: Must contain the phandle to the reset controller.
|
||
|
|
- A pinctrl state named "default" may be defined to set pins in mode of
|
||
|
|
operation for SPI transfer.
|
||
|
|
- dmas: DMA specifiers for tx and rx dma. DMA fifo mode must be used. See the
|
||
|
|
STM32 DMA bindings, Documentation/devicetree/bindings/dma/stm32-dma.txt.
|
||
|
|
- dma-names: DMA request names should include "tx" and "rx" if present.
|
||
|
|
- cs-gpios: list of GPIO chip selects. See the SPI bus bindings,
|
||
|
|
Documentation/devicetree/bindings/spi/spi-bus.txt
|
||
|
|
|
||
|
|
|
||
|
|
Child nodes represent devices on the SPI bus
|
||
|
|
See ../spi/spi-bus.txt
|
||
|
|
|
||
|
|
Optional properties:
|
||
|
|
- st,spi-midi-ns: (Master Inter-Data Idleness) minimum time delay in
|
||
|
|
nanoseconds inserted between two consecutive data frames.
|
||
|
|
|
||
|
|
|
||
|
|
Example:
|
||
|
|
spi2: spi@40003800 {
|
||
|
|
#address-cells = <1>;
|
||
|
|
#size-cells = <0>;
|
||
|
|
compatible = "st,stm32h7-spi";
|
||
|
|
reg = <0x40003800 0x400>;
|
||
|
|
interrupts = <36>;
|
||
|
|
clocks = <&rcc SPI2_CK>;
|
||
|
|
resets = <&rcc 1166>;
|
||
|
|
dmas = <&dmamux1 0 39 0x400 0x01>,
|
||
|
|
<&dmamux1 1 40 0x400 0x01>;
|
||
|
|
dma-names = "rx", "tx";
|
||
|
|
pinctrl-0 = <&spi2_pins_b>;
|
||
|
|
pinctrl-names = "default";
|
||
|
|
cs-gpios = <&gpioa 11 0>;
|
||
|
|
|
||
|
|
aardvark@0 {
|
||
|
|
compatible = "totalphase,aardvark";
|
||
|
|
reg = <0>;
|
||
|
|
spi-max-frequency = <4000000>;
|
||
|
|
st,spi-midi-ns = <4000>;
|
||
|
|
};
|
||
|
|
};
|