65 lines
1.7 KiB
Plaintext
65 lines
1.7 KiB
Plaintext
|
#
|
||
|
|
# Micrel device configuration
|
||
|
|
#
|
||
|
|
|
||
|
|
config NET_VENDOR_MICREL
|
||
|
|
bool "Micrel devices"
|
||
|
|
default y
|
||
|
|
depends on (HAS_IOMEM && DMA_ENGINE) || SPI || PCI || HAS_IOMEM || \
|
||
|
|
(ARM && ARCH_KS8695)
|
||
|
|
---help---
|
||
|
|
If you have a network (Ethernet) card belonging to this class, say Y.
|
||
|
|
|
||
|
|
Note that the answer to this question doesn't directly affect the
|
||
|
|
kernel: saying N will just cause the configurator to skip all
|
||
|
|
the questions about Micrel devices. If you say Y, you will be asked
|
||
|
|
for your specific card in the following questions.
|
||
|
|
|
||
|
|
if NET_VENDOR_MICREL
|
||
|
|
|
||
|
|
config ARM_KS8695_ETHER
|
||
|
|
tristate "KS8695 Ethernet support"
|
||
|
|
depends on ARM && ARCH_KS8695
|
||
|
|
select MII
|
||
|
|
---help---
|
||
|
|
If you wish to compile a kernel for the KS8695 and want to
|
||
|
|
use the internal ethernet then you should answer Y to this.
|
||
|
|
|
||
|
|
config KS8842
|
||
|
|
tristate "Micrel KSZ8841/42 with generic bus interface"
|
||
|
|
depends on HAS_IOMEM && DMA_ENGINE
|
||
|
|
---help---
|
||
|
|
This platform driver is for KSZ8841(1-port) / KS8842(2-port)
|
||
|
|
ethernet switch chip (managed, VLAN, QoS) from Micrel or
|
||
|
|
Timberdale(FPGA).
|
||
|
|
|
||
|
|
config KS8851
|
||
|
|
tristate "Micrel KS8851 SPI"
|
||
|
|
depends on SPI
|
||
|
|
select MII
|
||
|
|
select CRC32
|
||
|
|
select EEPROM_93CX6
|
||
|
|
---help---
|
||
|
|
SPI driver for Micrel KS8851 SPI attached network chip.
|
||
|
|
|
||
|
|
config KS8851_MLL
|
||
|
|
tristate "Micrel KS8851 MLL"
|
||
|
|
depends on HAS_IOMEM
|
||
|
|
select MII
|
||
|
|
---help---
|
||
|
|
This platform driver is for Micrel KS8851 Address/data bus
|
||
|
|
multiplexed network chip.
|
||
|
|
|
||
|
|
config KSZ884X_PCI
|
||
|
|
tristate "Micrel KSZ8841/2 PCI"
|
||
|
|
depends on PCI
|
||
|
|
select MII
|
||
|
|
select CRC32
|
||
|
|
---help---
|
||
|
|
This PCI driver is for Micrel KSZ8841/KSZ8842 PCI Ethernet chip.
|
||
|
|
|
||
|
|
To compile this driver as a module, choose M here. The module
|
||
|
|
will be called ksz884x.
|
||
|
|
|
||
|
|
endif # NET_VENDOR_MICREL
|