73 lines
1.8 KiB
Plaintext
73 lines
1.8 KiB
Plaintext
|
This document explains only the device tree data binding. For general
|
||
|
|
information about PHY subsystem refer to Documentation/phy.txt
|
||
|
|
|
||
|
|
PHY device node
|
||
|
|
===============
|
||
|
|
|
||
|
|
Required Properties:
|
||
|
|
#phy-cells: Number of cells in a PHY specifier; The meaning of all those
|
||
|
|
cells is defined by the binding for the phy node. The PHY
|
||
|
|
provider can use the values in cells to find the appropriate
|
||
|
|
PHY.
|
||
|
|
|
||
|
|
Optional Properties:
|
||
|
|
phy-supply: Phandle to a regulator that provides power to the PHY. This
|
||
|
|
regulator will be managed during the PHY power on/off sequence.
|
||
|
|
|
||
|
|
For example:
|
||
|
|
|
||
|
|
phys: phy {
|
||
|
|
compatible = "xxx";
|
||
|
|
reg = <...>;
|
||
|
|
.
|
||
|
|
.
|
||
|
|
#phy-cells = <1>;
|
||
|
|
.
|
||
|
|
.
|
||
|
|
};
|
||
|
|
|
||
|
|
That node describes an IP block (PHY provider) that implements 2 different PHYs.
|
||
|
|
In order to differentiate between these 2 PHYs, an additional specifier should be
|
||
|
|
given while trying to get a reference to it.
|
||
|
|
|
||
|
|
PHY user node
|
||
|
|
=============
|
||
|
|
|
||
|
|
Required Properties:
|
||
|
|
phys : the phandle for the PHY device (used by the PHY subsystem; not to be
|
||
|
|
confused with the Ethernet specific 'phy' and 'phy-handle' properties,
|
||
|
|
see Documentation/devicetree/bindings/net/ethernet.txt for these)
|
||
|
|
phy-names : the names of the PHY corresponding to the PHYs present in the
|
||
|
|
*phys* phandle
|
||
|
|
|
||
|
|
Example 1:
|
||
|
|
usb1: usb_otg_ss@xxx {
|
||
|
|
compatible = "xxx";
|
||
|
|
reg = <xxx>;
|
||
|
|
.
|
||
|
|
.
|
||
|
|
phys = <&usb2_phy>, <&usb3_phy>;
|
||
|
|
phy-names = "usb2phy", "usb3phy";
|
||
|
|
.
|
||
|
|
.
|
||
|
|
};
|
||
|
|
|
||
|
|
This node represents a controller that uses two PHYs, one for usb2 and one for
|
||
|
|
usb3.
|
||
|
|
|
||
|
|
Example 2:
|
||
|
|
usb2: usb_otg_ss@xxx {
|
||
|
|
compatible = "xxx";
|
||
|
|
reg = <xxx>;
|
||
|
|
.
|
||
|
|
.
|
||
|
|
phys = <&phys 1>;
|
||
|
|
phy-names = "usbphy";
|
||
|
|
.
|
||
|
|
.
|
||
|
|
};
|
||
|
|
|
||
|
|
This node represents a controller that uses one of the PHYs of the PHY provider
|
||
|
|
device defined previously. Note that the phy handle has an additional specifier
|
||
|
|
"1" to differentiate between the two PHYs.
|