/* * U300 clock implementation * Copyright (C) 2007-2012 ST-Ericsson AB * License terms: GNU General Public License (GPL) version 2 * Author: Linus Walleij * Author: Jonas Aaberg */ #include #include #include #include #include #include #include #include /* APP side SYSCON registers */ /* CLK Control Register 16bit (R/W) */ #define U300_SYSCON_CCR (0x0000) #define U300_SYSCON_CCR_I2S1_USE_VCXO (0x0040) #define U300_SYSCON_CCR_I2S0_USE_VCXO (0x0020) #define U300_SYSCON_CCR_TURN_VCXO_ON (0x0008) #define U300_SYSCON_CCR_CLKING_PERFORMANCE_MASK (0x0007) #define U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW_POWER (0x04) #define U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW (0x03) #define U300_SYSCON_CCR_CLKING_PERFORMANCE_INTERMEDIATE (0x02) #define U300_SYSCON_CCR_CLKING_PERFORMANCE_HIGH (0x01) #define U300_SYSCON_CCR_CLKING_PERFORMANCE_BEST (0x00) /* CLK Status Register 16bit (R/W) */ #define U300_SYSCON_CSR (0x0004) #define U300_SYSCON_CSR_PLL208_LOCK_IND (0x0002) #define U300_SYSCON_CSR_PLL13_LOCK_IND (0x0001) /* Reset lines for SLOW devices 16bit (R/W) */ #define U300_SYSCON_RSR (0x0014) #define U300_SYSCON_RSR_PPM_RESET_EN (0x0200) #define U300_SYSCON_RSR_ACC_TMR_RESET_EN (0x0100) #define U300_SYSCON_RSR_APP_TMR_RESET_EN (0x0080) #define U300_SYSCON_RSR_RTC_RESET_EN (0x0040) #define U300_SYSCON_RSR_KEYPAD_RESET_EN (0x0020) #define U300_SYSCON_RSR_GPIO_RESET_EN (0x0010) #define U300_SYSCON_RSR_EH_RESET_EN (0x0008) #define U300_SYSCON_RSR_BTR_RESET_EN (0x0004) #define U300_SYSCON_RSR_UART_RESET_EN (0x0002) #define U300_SYSCON_RSR_SLOW_BRIDGE_RESET_EN (0x0001) /* Reset lines for FAST devices 16bit (R/W) */ #define U300_SYSCON_RFR (0x0018) #define U300_SYSCON_RFR_UART1_RESET_ENABLE (0x0080) #define U300_SYSCON_RFR_SPI_RESET_ENABLE (0x0040) #define U300_SYSCON_RFR_MMC_RESET_ENABLE (0x0020) #define U300_SYSCON_RFR_PCM_I2S1_RESET_ENABLE (0x0010) #define U300_SYSCON_RFR_PCM_I2S0_RESET_ENABLE (0x0008) #define U300_SYSCON_RFR_I2C1_RESET_ENABLE (0x0004) #define U300_SYSCON_RFR_I2C0_RESET_ENABLE (0x0002) #define U300_SYSCON_RFR_FAST_BRIDGE_RESET_ENABLE (0x0001) /* Reset lines for the rest of the peripherals 16bit (R/W) */ #define U300_SYSCON_RRR (0x001c) #define U300_SYSCON_RRR_CDS_RESET_EN (0x4000) #define U300_SYSCON_RRR_ISP_RESET_EN (0x2000) #define U300_SYSCON_RRR_INTCON_RESET_EN (0x1000) #define U300_SYSCON_RRR_MSPRO_RESET_EN (0x0800) #define U300_SYSCON_RRR_XGAM_RESET_EN (0x0100) #define U300_SYSCON_RRR_XGAM_VC_SYNC_RESET_EN (0x0080) #define U300_SYSCON_RRR_NANDIF_RESET_EN (0x0040) #define U300_SYSCON_RRR_EMIF_RESET_EN (0x0020) #define U300_SYSCON_RRR_DMAC_RESET_EN (0x0010) #define U300_SYSCON_RRR_CPU_RESET_EN (0x0008) #define U300_SYSCON_RRR_APEX_RESET_EN (0x0004) #define U300_SYSCON_RRR_AHB_RESET_EN (0x0002) #define U300_SYSCON_RRR_AAIF_RESET_EN (0x0001) /* Clock enable for SLOW peripherals 16bit (R/W) */ #define U300_SYSCON_CESR (0x0020) #define U300_SYSCON_CESR_PPM_CLK_EN (0x0200) #define U300_SYSCON_CESR_ACC_TMR_CLK_EN (0x0100) #define U300_SYSCON_CESR_APP_TMR_CLK_EN (0x0080) #define U300_SYSCON_CESR_KEYPAD_CLK_EN (0x0040) #define U300_SYSCON_CESR_GPIO_CLK_EN (0x0010) #define U300_SYSCON_CESR_EH_CLK_EN (0x0008) #define U300_SYSCON_CESR_BTR_CLK_EN (0x0004) #define U300_SYSCON_CESR_UART_CLK_EN (0x0002) #define U300_SYSCON_CESR_SLOW_BRIDGE_CLK_EN (0x0001) /* Clock enable for FAST peripherals 16bit (R/W) */ #define U300_SYSCON_CEFR (0x0024) #define U300_SYSCON_CEFR_UART1_CLK_EN (0x0200) #define U300_SYSCON_CEFR_I2S1_CORE_CLK_EN (0x0100) #define U300_SYSCON_CEFR_I2S0_CORE_CLK_EN (0x0080) #define U300_SYSCON_CEFR_SPI_CLK_EN (0x0040) #define U300_SYSCON_CEFR_MMC_CLK_EN (0x0020) #define U300_SYSCON_CEFR_I2S1_CLK_EN (0x0010) #define U300_SYSCON_CEFR_I2S0_CLK_EN (0x0008) #define U300_SYSCON_CEFR_I2C1_CLK_EN (0x0004) #define U300_SYSCON_CEFR_I2C0_CLK_EN (0x0002) #define U300_SYSCON_CEFR_FAST_BRIDGE_CLK_EN (0x0001) /* Clock enable for the rest of the peripherals 16bit (R/W) */ #define U300_SYSCON_CERR (0x0028) #define U300_SYSCON_CERR_CDS_CLK_EN (0x2000) #define U300_SYSCON_CERR_ISP_CLK_EN (0x1000) #define U300_SYSCON_CERR_MSPRO_CLK_EN (0x0800) #define U300_SYSCON_CERR_AHB_SUBSYS_BRIDGE_CLK_EN (0x0400) #define U300_SYSCON_CERR_SEMI_CLK_EN (0x0200) #define U300_SYSCON_CERR_XGAM_CLK_EN (0x0100) #define U300_SYSCON_CERR_VIDEO_ENC_CLK_EN (0x0080) #define U300_SYSCON_CERR_NANDIF_CLK_EN (0x0040) #define U300_SYSCON_CERR_EMIF_CLK_EN (0x0020) #define U300_SYSCON_CERR_DMAC_CLK_EN (0x0010) #define U300_SYSCON_CERR_CPU_CLK_EN (0x0008) #define U300_SYSCON_CERR_APEX_CLK_EN (0x0004) #define U300_SYSCON_CERR_AHB_CLK_EN (0x0002) #define U300_SYSCON_CERR_AAIF_CLK_EN (0x0001) /* Single block clock enable 16bit (-/W) */ #define U300_SYSCON_SBCER (0x002c) #define U300_SYSCON_SBCER_PPM_CLK_EN (0x0009) #define U300_SYSCON_SBCER_ACC_TMR_CLK_EN (0x0008) #define U300_SYSCON_SBCER_APP_TMR_CLK_EN (0x0007) #define U300_SYSCON_SBCER_KEYPAD_CLK_EN (0x0006) #define U300_SYSCON_SBCER_GPIO_CLK_EN (0x0004) #define U300_SYSCON_SBCER_EH_CLK_EN (0x0003) #define U300_SYSCON_SBCER_BTR_CLK_EN (0x0002) #define U300_SYSCON_SBCER_UART_CLK_EN (0x0001) #define U300_SYSCON_SBCER_SLOW_BRIDGE_CLK_EN (0x0000) #define U300_SYSCON_SBCER_UART1_CLK_EN (0x0019) #define U300_SYSCON_SBCER_I2S1_CORE_CLK_EN (0x0018) #define U300_SYSCON_SBCER_I2S0_CORE_CLK_EN (0x0017) #define U300_SYSCON_SBCER_SPI_CLK_EN (0x0016) #define U300_SYSCON_SBCER_MMC_CLK_EN (0x0015) #define U300_SYSCON_SBCER_I2S1_CLK_EN (0x0014) #define U300_SYSCON_SBCER_I2S0_CLK_EN (0x0013) #define U300_SYSCON_SBCER_I2C1_CLK_EN (0x0012) #define U300_SYSCON_SBCER_I2C0_CLK_EN (0x0011) #define U300_SYSCON_SBCER_FAST_BRIDGE_CLK_EN (0x0010) #define U300_SYSCON_SBCER_CDS_CLK_EN (0x002D) #define U300_SYSCON_SBCER_ISP_CLK_EN (0x002C) #define U300_SYSCON_SBCER_MSPRO_CLK_EN (0x002B) #define U300_SYSCON_SBCER_AHB_SUBSYS_BRIDGE_CLK_EN (0x002A) #define U300_SYSCON_SBCER_SEMI_CLK_EN (0x0029) #define U300_SYSCON_SBCER_XGAM_CLK_EN (0x0028) #define U300_SYSCON_SBCER_VIDEO_ENC_CLK_EN (0x0027) #define U300_SYSCON_SBCER_NANDIF_CLK_EN (0x0026) #define U300_SYSCON_SBCER_EMIF_CLK_EN (0x0025) #define U300_SYSCON_SBCER_DMAC_CLK_EN (0x0024) #define U300_SYSCON_SBCER_CPU_CLK_EN (0x0023) #define U300_SYSCON_SBCER_APEX_CLK_EN (0x0022) #define U300_SYSCON_SBCER_AHB_CLK_EN (0x0021) #define U300_SYSCON_SBCER_AAIF_CLK_EN (0x0020) /* Single block clock disable 16bit (-/W) */ #define U300_SYSCON_SBCDR (0x0030) /* Same values as above for SBCER */ /* Clock force SLOW peripherals 16bit (R/W) */ #define U300_SYSCON_CFSR (0x003c) #define U300_SYSCON_CFSR_PPM_CLK_FORCE_EN (0x0200) #define U300_SYSCON_CFSR_ACC_TMR_CLK_FORCE_EN (0x0100) #define U300_SYSCON_CFSR_APP_TMR_CLK_FORCE_EN (0x0080) #define U300_SYSCON_CFSR_KEYPAD_CLK_FORCE_EN (0x0020) #define U300_SYSCON_CFSR_GPIO_CLK_FORCE_EN (0x0010) #define U300_SYSCON_CFSR_EH_CLK_FORCE_EN (0x0008) #define U300_SYSCON_CFSR_BTR_CLK_FORCE_EN (0x0004) #define U300_SYSCON_CFSR_UART_CLK_FORCE_EN (0x0002) #define U300_SYSCON_CFSR_SLOW_BRIDGE_CLK_FORCE_EN (0x0001) /* Clock force FAST peripherals 16bit (R/W) */ #define U300_SYSCON_CFFR (0x40) /* Values not defined. Define if you want to use them. */ /* Clock force the rest of the peripherals 16bit (R/W) */ #define U300_SYSCON_CFRR (0x44) #define U300_SYSCON_CFRR_CDS_CLK_FORCE_EN (0x2000) #define U300_SYSCON_CFRR_ISP_CLK_FORCE_EN (0x1000) #define U300_SYSCON_CFRR_MSPRO_CLK_FORCE_EN (0x0800) #define U300_SYSCON_CFRR_AHB_SUBSYS_BRIDGE_CLK_FORCE_EN (0x0400) #define U300_SYSCON_CFRR_SEMI_CLK_FORCE_EN (0x0200) #define U300_SYSCON_CFRR_XGAM_CLK_FORCE_EN (0x0100) #define U300_SYSCON_CFRR_VIDEO_ENC_CLK_FORCE_EN (0x0080) #define U300_SYSCON_CFRR_NANDIF_CLK_FORCE_EN (0x0040) #define U300_SYSCON_CFRR_EMIF_CLK_FORCE_EN (0x0020) #define U300_SYSCON_CFRR_DMAC_CLK_FORCE_EN (0x0010) #define U300_SYSCON_CFRR_CPU_CLK_FORCE_EN (0x0008) #define U300_SYSCON_CFRR_APEX_CLK_FORCE_EN (0x0004) #define U300_SYSCON_CFRR_AHB_CLK_FORCE_EN (0x0002) #define U300_SYSCON_CFRR_AAIF_CLK_FORCE_EN (0x0001) /* PLL208 Frequency Control 16bit (R/W) */ #define U300_SYSCON_PFCR (0x48) #define U300_SYSCON_PFCR_DPLL_MULT_NUM (0x000F) /* Power Management Control 16bit (R/W) */ #define U300_SYSCON_PMCR (0x50) #define U300_SYSCON_PMCR_DCON_ENABLE (0x0002) #define U300_SYSCON_PMCR_PWR_MGNT_ENABLE (0x0001) /* Reset Out 16bit (R/W) */ #define U300_SYSCON_RCR (0x6c) #define U300_SYSCON_RCR_RESOUT0_RST_N_DISABLE (0x0001) /* EMIF Slew Rate Control 16bit (R/W) */ #define U300_SYSCON_SRCLR (0x70) #define U300_SYSCON_SRCLR_MASK (0x03FF) #define U300_SYSCON_SRCLR_VALUE (0x03FF) #define U300_SYSCON_SRCLR_EMIF_1_SLRC_5_B (0x0200) #define U300_SYSCON_SRCLR_EMIF_1_SLRC_5_A (0x0100) #define U300_SYSCON_SRCLR_EMIF_1_SLRC_4_B (0x0080) #define U300_SYSCON_SRCLR_EMIF_1_SLRC_4_A (0x0040) #define U300_SYSCON_SRCLR_EMIF_1_SLRC_3_B (0x0020) #define U300_SYSCON_SRCLR_EMIF_1_SLRC_3_A (0x0010) #define U300_SYSCON_SRCLR_EMIF_1_SLRC_2_B (0x0008) #define U300_SYSCON_SRCLR_EMIF_1_SLRC_2_A (0x0004) #define U300_SYSCON_SRCLR_EMIF_1_SLRC_1_B (0x0002) #define U300_SYSCON_SRCLR_EMIF_1_SLRC_1_A (0x0001) /* EMIF Clock Control Register 16bit (R/W) */ #define U300_SYSCON_ECCR (0x0078) #define U300_SYSCON_ECCR_MASK (0x000F) #define U300_SYSCON_ECCR_EMIF_1_STATIC_CLK_EN_N_DISABLE (0x0008) #define U300_SYSCON_ECCR_EMIF_1_RET_OUT_CLK_EN_N_DISABLE (0x0004) #define U300_SYSCON_ECCR_EMIF_MEMCLK_RET_EN_N_DISABLE (0x0002) #define U300_SYSCON_ECCR_EMIF_SDRCLK_RET_EN_N_DISABLE (0x0001) /* MMC/MSPRO frequency divider register 0 16bit (R/W) */ #define U300_SYSCON_MMF0R (0x90) #define U300_SYSCON_MMF0R_MASK (0x00FF) #define U300_SYSCON_MMF0R_FREQ_0_HIGH_MASK (0x00F0) #define U300_SYSCON_MMF0R_FREQ_0_LOW_MASK (0x000F) /* MMC/MSPRO frequency divider register 1 16bit (R/W) */ #define U300_SYSCON_MMF1R (0x94) #define U300_SYSCON_MMF1R_MASK (0x00FF) #define U300_SYSCON_MMF1R_FREQ_1_HIGH_MASK (0x00F0) #define U300_SYSCON_MMF1R_FREQ_1_LOW_MASK (0x000F) /* Clock control for the MMC and MSPRO blocks 16bit (R/W) */ #define U300_SYSCON_MMCR (0x9C) #define U300_SYSCON_MMCR_MASK (0x0003) #define U300_SYSCON_MMCR_MMC_FB_CLK_SEL_ENABLE (0x0002) #define U300_SYSCON_MMCR_MSPRO_FREQSEL_ENABLE (0x0001) /* SYS_0_CLK_CONTROL first clock control 16bit (R/W) */ #define U300_SYSCON_S0CCR (0x120) #define U300_SYSCON_S0CCR_FIELD_MASK (0x43FF) #define U300_SYSCON_S0CCR_CLOCK_REQ (0x4000) #define U300_SYSCON_S0CCR_CLOCK_REQ_MONITOR (0x2000) #define U300_SYSCON_S0CCR_CLOCK_INV (0x0200) #define U300_SYSCON_S0CCR_CLOCK_FREQ_MASK (0x01E0) #define U300_SYSCON_S0CCR_CLOCK_SELECT_MASK (0x001E) #define U300_SYSCON_S0CCR_CLOCK_ENABLE (0x0001) #define U300_SYSCON_S0CCR_SEL_MCLK (0x8 << 1) #define U300_SYSCON_S0CCR_SEL_ACC_FSM_CLK (0xA << 1) #define U300_SYSCON_S0CCR_SEL_PLL60_48_CLK (0xC << 1) #define U300_SYSCON_S0CCR_SEL_PLL60_60_CLK (0xD << 1) #define U300_SYSCON_S0CCR_SEL_ACC_PLL208_CLK (0xE << 1) #define U300_SYSCON_S0CCR_SEL_APP_PLL13_CLK (0x0 << 1) #define U300_SYSCON_S0CCR_SEL_APP_FSM_CLK (0x2 << 1) #define U300_SYSCON_S0CCR_SEL_RTC_CLK (0x4 << 1) #define U300_SYSCON_S0CCR_SEL_APP_PLL208_CLK (0x6 << 1) /* SYS_1_CLK_CONTROL second clock control 16 bit (R/W) */ #define U300_SYSCON_S1CCR (0x124) #define U300_SYSCON_S1CCR_FIELD_MASK (0x43FF) #define U300_SYSCON_S1CCR_CLOCK_REQ (0x4000) #define U300_SYSCON_S1CCR_CLOCK_REQ_MONITOR (0x2000) #define U300_SYSCON_S1CCR_CLOCK_INV (0x0200) #define U300_SYSCON_S1CCR_CLOCK_FREQ_MASK (0x01E0) #define U300_SYSCON_S1CCR_CLOCK_SELECT_MASK (0x001E) #define U300_SYSCON_S1CCR_CLOCK_ENABLE (0x0001) #define U300_SYSCON_S1CCR_SEL_MCLK (0x8 << 1) #define U300_SYSCON_S1CCR_SEL_ACC_FSM_CLK (0xA << 1) #define U300_SYSCON_S1CCR_SEL_PLL60_48_CLK (0xC << 1) #define U300_SYSCON_S1CCR_SEL_PLL60_60_CLK (0xD << 1) #define U300_SYSCON_S1CCR_SEL_ACC_PLL208_CLK (0xE << 1) #define U300_SYSCON_S1CCR_SEL_ACC_PLL13_CLK (0x0 << 1) #define U300_SYSCON_S1CCR_SEL_APP_FSM_CLK (0x2 << 1) #define U300_SYSCON_S1CCR_SEL_RTC_CLK (0x4 << 1) #define U300_SYSCON_S1CCR_SEL_APP_PLL208_CLK (0x6 << 1) /* SYS_2_CLK_CONTROL third clock control 16 bit (R/W) */ #define U300_SYSCON_S2CCR (0x128) #define U300_SYSCON_S2CCR_FIELD_MASK (0xC3FF) #define U300_SYSCON_S2CCR_CLK_STEAL (0x8000) #define U300_SYSCON_S2CCR_CLOCK_REQ (0x4000) #define U300_SYSCON_S2CCR_CLOCK_REQ_MONITOR (0x2000) #define U300_SYSCON_S2CCR_CLOCK_INV (0x0200) #define U300_SYSCON_S2CCR_CLOCK_FREQ_MASK (0x01E0) #define U300_SYSCON_S2CCR_CLOCK_SELECT_MASK (0x001E) #define U300_SYSCON_S2CCR_CLOCK_ENABLE (0x0001) #define U300_SYSCON_S2CCR_SEL_MCLK (0x8 << 1) #define U300_SYSCON_S2CCR_SEL_ACC_FSM_CLK (0xA << 1) #define U300_SYSCON_S2CCR_SEL_PLL60_48_CLK (0xC << 1) #define U300_SYSCON_S2CCR_SEL_PLL60_60_CLK (0xD << 1) #define U300_SYSCON_S2CCR_SEL_ACC_PLL208_CLK (0xE << 1) #define U300_SYSCON_S2CCR_SEL_ACC_PLL13_CLK (0x0 << 1) #define U300_SYSCON_S2CCR_SEL_APP_FSM_CLK (0x2 << 1) #define U300_SYSCON_S2CCR_SEL_RTC_CLK (0x4 << 1) #define U300_SYSCON_S2CCR_SEL_APP_PLL208_CLK (0x6 << 1) /* SC_PLL_IRQ_CONTROL 16bit (R/W) */ #define U300_SYSCON_PICR (0x0130) #define U300_SYSCON_PICR_MASK (0x00FF) #define U300_SYSCON_PICR_FORCE_PLL208_LOCK_LOW_ENABLE (0x0080) #define U300_SYSCON_PICR_FORCE_PLL208_LOCK_HIGH_ENABLE (0x0040) #define U300_SYSCON_PICR_FORCE_PLL13_LOCK_LOW_ENABLE (0x0020) #define U300_SYSCON_PICR_FORCE_PLL13_LOCK_HIGH_ENABLE (0x0010) #define U300_SYSCON_PICR_IRQMASK_PLL13_UNLOCK_ENABLE (0x0008) #define U300_SYSCON_PICR_IRQMASK_PLL13_LOCK_ENABLE (0x0004) #define U300_SYSCON_PICR_IRQMASK_PLL208_UNLOCK_ENABLE (0x0002) #define U300_SYSCON_PICR_IRQMASK_PLL208_LOCK_ENABLE (0x0001) /* SC_PLL_IRQ_STATUS 16 bit (R/-) */ #define U300_SYSCON_PISR (0x0134) #define U300_SYSCON_PISR_MASK (0x000F) #define U300_SYSCON_PISR_PLL13_UNLOCK_IND (0x0008) #define U300_SYSCON_PISR_PLL13_LOCK_IND (0x0004) #define U300_SYSCON_PISR_PLL208_UNLOCK_IND (0x0002) #define U300_SYSCON_PISR_PLL208_LOCK_IND (0x0001) /* SC_PLL_IRQ_CLEAR 16 bit (-/W) */ #define U300_SYSCON_PICLR (0x0138) #define U300_SYSCON_PICLR_MASK (0x000F) #define U300_SYSCON_PICLR_RWMASK (0x0000) #define U300_SYSCON_PICLR_PLL13_UNLOCK_SC (0x0008) #define U300_SYSCON_PICLR_PLL13_LOCK_SC (0x0004) #define U300_SYSCON_PICLR_PLL208_UNLOCK_SC (0x0002) #define U300_SYSCON_PICLR_PLL208_LOCK_SC (0x0001) /* Clock activity observability register 0 */ #define U300_SYSCON_C0OAR (0x140) #define U300_SYSCON_C0OAR_MASK (0xFFFF) #define U300_SYSCON_C0OAR_VALUE (0xFFFF) #define U300_SYSCON_C0OAR_BT_H_CLK (0x8000) #define U300_SYSCON_C0OAR_ASPB_P_CLK (0x4000) #define U300_SYSCON_C0OAR_APP_SEMI_H_CLK (0x2000) #define U300_SYSCON_C0OAR_APP_SEMI_CLK (0x1000) #define U300_SYSCON_C0OAR_APP_MMC_MSPRO_CLK (0x0800) #define U300_SYSCON_C0OAR_APP_I2S1_CLK (0x0400) #define U300_SYSCON_C0OAR_APP_I2S0_CLK (0x0200) #define U300_SYSCON_C0OAR_APP_CPU_CLK (0x0100) #define U300_SYSCON_C0OAR_APP_52_CLK (0x0080) #define U300_SYSCON_C0OAR_APP_208_CLK (0x0040) #define U300_SYSCON_C0OAR_APP_104_CLK (0x0020) #define U300_SYSCON_C0OAR_APEX_CLK (0x0010) #define U300_SYSCON_C0OAR_AHPB_M_H_CLK (0x0008) #define U300_SYSCON_C0OAR_AHB_CLK (0x0004) #define U300_SYSCON_C0OAR_AFPB_P_CLK (0x0002) #define U300_SYSCON_C0OAR_AAIF_CLK (0x0001) /* Clock activity observability register 1 */ #define U300_SYSCON_C1OAR (0x144) #define U300_SYSCON_C1OAR_MASK (0x3FFE) #define U300_SYSCON_C1OAR_VALUE (0x3FFE) #define U300_SYSCON_C1OAR_NFIF_F_CLK (0x2000) #define U300_SYSCON_C1OAR_MSPRO_CLK (0x1000) #define U300_SYSCON_C1OAR_MMC_P_CLK (0x0800) #define U300_SYSCON_C1OAR_MMC_CLK (0x0400) #define U300_SYSCON_C1OAR_KP_P_CLK (0x0200) #define U300_SYSCON_C1OAR_I2C1_P_CLK (0x0100) #define U300_SYSCON_C1OAR_I2C0_P_CLK (0x0080) #define U300_SYSCON_C1OAR_GPIO_CLK (0x0040) #define U300_SYSCON_C1OAR_EMIF_MPMC_CLK (0x0020) #define U300_SYSCON_C1OAR_EMIF_H_CLK (0x0010) #define U300_SYSCON_C1OAR_EVHIST_CLK (0x0008) #define U300_SYSCON_C1OAR_PPM_CLK (0x0004) #define U300_SYSCON_C1OAR_DMA_CLK (0x0002) /* Clock activity observability register 2 */ #define U300_SYSCON_C2OAR (0x148) #define U300_SYSCON_C2OAR_MASK (0x0FFF) #define U300_SYSCON_C2OAR_VALUE (0x0FFF) #define U300_SYSCON_C2OAR_XGAM_CDI_CLK (0x0800) #define U300_SYSCON_C2OAR_XGAM_CLK (0x0400) #define U300_SYSCON_C2OAR_VC_H_CLK (0x0200) #define U300_SYSCON_C2OAR_VC_CLK (0x0100) #define U300_SYSCON_C2OAR_UA_P_CLK (0x0080) #define U300_SYSCON_C2OAR_TMR1_CLK (0x0040) #define U300_SYSCON_C2OAR_TMR0_CLK (0x0020) #define U300_SYSCON_C2OAR_SPI_P_CLK (0x0010) #define U300_SYSCON_C2OAR_PCM_I2S1_CORE_CLK (0x0008) #define U300_SYSCON_C2OAR_PCM_I2S1_CLK (0x0004) #define U300_SYSCON_C2OAR_PCM_I2S0_CORE_CLK (0x0002) #define U300_SYSCON_C2OAR_PCM_I2S0_CLK (0x0001) /* * The clocking hierarchy currently looks like this. * NOTE: the idea is NOT to show how the clocks are routed on the chip! * The ideas is to show dependencies, so a clock higher up in the * hierarchy has to be on in order for another clock to be on. Now, * both CPU and DMA can actually be on top of the hierarchy, and that * is not modeled currently. Instead we have the backbone AMBA bus on * top. This bus cannot be programmed in any way but conceptually it * needs to be active for the bridges and devices to transport data. * * Please be aware that a few clocks are hw controlled, which mean that * the hw itself can turn on/off or change the rate of the clock when * needed! * * AMBA bus * | * +- CPU * +- FSMC NANDIF NAND Flash interface * +- SEMI Shared Memory interface * +- ISP Image Signal Processor (U335 only) * +- CDS (U335 only) * +- DMA Direct Memory Access Controller * +- AAIF APP/ACC Interface (Mobile Scalable Link, MSL) * +- APEX * +- VIDEO_ENC AVE2/3 Video Encoder * +- XGAM Graphics Accelerator Controller * +- AHB * | * +- ahb:0 AHB Bridge * | | * | +- ahb:1 INTCON Interrupt controller * | +- ahb:3 MSPRO Memory Stick Pro controller * | +- ahb:4 EMIF External Memory interface * | * +- fast:0 FAST bridge * | | * | +- fast:1 MMCSD MMC/SD card reader controller * | +- fast:2 I2S0 PCM I2S channel 0 controller * | +- fast:3 I2S1 PCM I2S channel 1 controller * | +- fast:4 I2C0 I2C channel 0 controller * | +- fast:5 I2C1 I2C channel 1 controller * | +- fast:6 SPI SPI controller * | +- fast:7 UART1 Secondary UART (U335 only) * | * +- slow:0 SLOW bridge * | * +- slow:1 SYSCON (not possible to control) * +- slow:2 WDOG Watchdog * +- slow:3 UART0 primary UART * +- slow:4 TIMER_APP Application timer - used in Linux * +- slow:5 KEYPAD controller * +- slow:6 GPIO controller * +- slow:7 RTC controller * +- slow:8 BT Bus Tracer (not used currently) * +- slow:9 EH Event Handler (not used currently) * +- slow:a TIMER_ACC Access style timer (not used currently) * +- slow:b PPM (U335 only, what is that?) */ /* Global syscon virtual base */ static void __iomem *syscon_vbase; /** * struct clk_syscon - U300 syscon clock * @hw: corresponding clock hardware entry * @hw_ctrld: whether this clock is hardware controlled (for refcount etc) * and does not need any magic pokes to be enabled/disabled * @reset: state holder, whether this block's reset line is asserted or not * @res_reg: reset line enable/disable flag register * @res_bit: bit for resetting or taking this consumer out of reset * @en_reg: clock line enable/disable flag register * @en_bit: bit for enabling/disabling this consumer clock line * @clk_val: magic value to poke in the register to enable/disable * this one clock */ struct clk_syscon { struct clk_hw hw; bool hw_ctrld; bool reset; void __iomem *res_reg; u8 res_bit; void __iomem *en_reg; u8 en_bit; u16 clk_val; }; #define to_syscon(_hw) container_of(_hw, struct clk_syscon, hw) static DEFINE_SPINLOCK(syscon_resetreg_lock); /* * Reset control functions. We remember if a block has been * taken out of reset and don't remove the reset assertion again * and vice versa. Currently we only remove resets so the * enablement function is defined out. */ static void syscon_block_reset_enable(struct clk_syscon *sclk) { unsigned long iflags; u16 val; /* Not all blocks support resetting */ if (!sclk->res_reg) return; spin_lock_irqsave(&syscon_resetreg_lock, iflags); val = readw(sclk->res_reg); val |= BIT(sclk->res_bit); writew(val, sclk->res_reg); spin_unlock_irqrestore(&syscon_resetreg_lock, iflags); sclk->reset = true; } static void syscon_block_reset_disable(struct clk_syscon *sclk) { unsigned long iflags; u16 val; /* Not all blocks support resetting */ if (!sclk->res_reg) return; spin_lock_irqsave(&syscon_resetreg_lock, iflags); val = readw(sclk->res_reg); val &= ~BIT(sclk->res_bit); writew(val, sclk->res_reg); spin_unlock_irqrestore(&syscon_resetreg_lock, iflags); sclk->reset = false; } static int syscon_clk_prepare(struct clk_hw *hw) { struct clk_syscon *sclk = to_syscon(hw); /* If the block is in reset, bring it out */ if (sclk->reset) syscon_block_reset_disable(sclk); return 0; } static void syscon_clk_unprepare(struct clk_hw *hw) { struct clk_syscon *sclk = to_syscon(hw); /* Please don't force the console into reset */ if (sclk->clk_val == U300_SYSCON_SBCER_UART_CLK_EN) return; /* When unpreparing, force block into reset */ if (!sclk->reset) syscon_block_reset_enable(sclk); } static int syscon_clk_enable(struct clk_hw *hw) { struct clk_syscon *sclk = to_syscon(hw); /* Don't touch the hardware controlled clocks */ if (sclk->hw_ctrld) return 0; /* These cannot be controlled */ if (sclk->clk_val == 0xFFFFU) return 0; writew(sclk->clk_val, syscon_vbase + U300_SYSCON_SBCER); return 0; } static void syscon_clk_disable(struct clk_hw *hw) { struct clk_syscon *sclk = to_syscon(hw); /* Don't touch the hardware controlled clocks */ if (sclk->hw_ctrld) return; if (sclk->clk_val == 0xFFFFU) return; /* Please don't disable the console port */ if (sclk->clk_val == U300_SYSCON_SBCER_UART_CLK_EN) return; writew(sclk->clk_val, syscon_vbase + U300_SYSCON_SBCDR); } static int syscon_clk_is_enabled(struct clk_hw *hw) { struct clk_syscon *sclk = to_syscon(hw); u16 val; /* If no enable register defined, it's always-on */ if (!sclk->en_reg) return 1; val = readw(sclk->en_reg); val &= BIT(sclk->en_bit); return val ? 1 : 0; } static u16 syscon_get_perf(void) { u16 val; val = readw(syscon_vbase + U300_SYSCON_CCR); val &= U300_SYSCON_CCR_CLKING_PERFORMANCE_MASK; return val; } static unsigned long syscon_clk_recalc_rate(struct clk_hw *hw, unsigned long parent_rate) { struct clk_syscon *sclk = to_syscon(hw); u16 perf = syscon_get_perf(); switch (sclk->clk_val) { case U300_SYSCON_SBCER_FAST_BRIDGE_CLK_EN: case U300_SYSCON_SBCER_I2C0_CLK_EN: case U300_SYSCON_SBCER_I2C1_CLK_EN: case U300_SYSCON_SBCER_MMC_CLK_EN: case U300_SYSCON_SBCER_SPI_CLK_EN: /* The FAST clocks have one progression */ switch (perf) { case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW_POWER: case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW: return 13000000; default: return parent_rate; /* 26 MHz */ } case U300_SYSCON_SBCER_DMAC_CLK_EN: case U300_SYSCON_SBCER_NANDIF_CLK_EN: case U300_SYSCON_SBCER_XGAM_CLK_EN: /* AMBA interconnect peripherals */ switch (perf) { case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW_POWER: case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW: return 6500000; case U300_SYSCON_CCR_CLKING_PERFORMANCE_INTERMEDIATE: return 26000000; default: return parent_rate; /* 52 MHz */ } case U300_SYSCON_SBCER_SEMI_CLK_EN: case U300_SYSCON_SBCER_EMIF_CLK_EN: /* EMIF speeds */ switch (perf) { case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW_POWER: case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW: return 13000000; case U300_SYSCON_CCR_CLKING_PERFORMANCE_INTERMEDIATE: return 52000000; default: return 104000000; } case U300_SYSCON_SBCER_CPU_CLK_EN: /* And the fast CPU clock */ switch (perf) { case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW_POWER: case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW: return 13000000; case U300_SYSCON_CCR_CLKING_PERFORMANCE_INTERMEDIATE: return 52000000; case U300_SYSCON_CCR_CLKING_PERFORMANCE_HIGH: return 104000000; default: return parent_rate; /* 208 MHz */ } default: /* * The SLOW clocks and default just inherit the rate of * their parent (typically PLL13 13 MHz). */ return parent_rate; } } static long syscon_clk_round_rate(struct clk_hw *hw, unsigned long rate, unsigned long *prate) { struct clk_syscon *sclk = to_syscon(hw); if (sclk->clk_val != U300_SYSCON_SBCER_CPU_CLK_EN) return *prate; /* We really only support setting the rate of the CPU clock */ if (rate <= 13000000) return 13000000; if (rate <= 52000000) return 52000000; if (rate <= 104000000) return 104000000; return 208000000; } static int syscon_clk_set_rate(struct clk_hw *hw, unsigned long rate, unsigned long parent_rate) { struct clk_syscon *sclk = to_syscon(hw); u16 val; /* We only support setting the rate of the CPU clock */ if (sclk->clk_val != U300_SYSCON_SBCER_CPU_CLK_EN) return -EINVAL; switch (rate) { case 13000000: val = U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW_POWER; break; case 52000000: val = U300_SYSCON_CCR_CLKING_PERFORMANCE_INTERMEDIATE; break; case 104000000: val = U300_SYSCON_CCR_CLKING_PERFORMANCE_HIGH; break; case 208000000: val = U300_SYSCON_CCR_CLKING_PERFORMANCE_BEST; break; default: return -EINVAL; } val |= readw(syscon_vbase + U300_SYSCON_CCR) & ~U300_SYSCON_CCR_CLKING_PERFORMANCE_MASK ; writew(val, syscon_vbase + U300_SYSCON_CCR); return 0; } static const struct clk_ops syscon_clk_ops = { .prepare = syscon_clk_prepare, .unprepare = syscon_clk_unprepare, .enable = syscon_clk_enable, .disable = syscon_clk_disable, .is_enabled = syscon_clk_is_enabled, .recalc_rate = syscon_clk_recalc_rate, .round_rate = syscon_clk_round_rate, .set_rate = syscon_clk_set_rate, }; static struct clk_hw * __init syscon_clk_register(struct device *dev, const char *name, const char *parent_name, unsigned long flags, bool hw_ctrld, void __iomem *res_reg, u8 res_bit, void __iomem *en_reg, u8 en_bit, u16 clk_val) { struct clk_hw *hw; struct clk_syscon *sclk; struct clk_init_data init = {}; int ret; sclk = kzalloc(sizeof(*sclk), GFP_KERNEL); if (!sclk) return ERR_PTR(-ENOMEM); init.name = name; init.ops = &syscon_clk_ops; init.flags = flags; init.parent_names = (parent_name ? &parent_name : NULL); init.num_parents = (parent_name ? 1 : 0); sclk->hw.init = &init; sclk->hw_ctrld = hw_ctrld; /* Assume the block is in reset at registration */ sclk->reset = true; sclk->res_reg = res_reg; sclk->res_bit = res_bit; sclk->en_reg = en_reg; sclk->en_bit = en_bit; sclk->clk_val = clk_val; hw = &sclk->hw; ret = clk_hw_register(dev, hw); if (ret) { kfree(sclk); hw = ERR_PTR(ret); } return hw; } #define U300_CLK_TYPE_SLOW 0 #define U300_CLK_TYPE_FAST 1 #define U300_CLK_TYPE_REST 2 /** * struct u300_clock - defines the bits and pieces for a certain clock * @type: the clock type, slow fast or rest * @id: the bit in the slow/fast/rest register for this clock * @hw_ctrld: whether the clock is hardware controlled * @clk_val: a value to poke in the one-write enable/disable registers */ struct u300_clock { u8 type; u8 id; bool hw_ctrld; u16 clk_val; }; static struct u300_clock const u300_clk_lookup[] __initconst = { { .type = U300_CLK_TYPE_REST, .id = 3, .hw_ctrld = true, .clk_val = U300_SYSCON_SBCER_CPU_CLK_EN, }, { .type = U300_CLK_TYPE_REST, .id = 4, .hw_ctrld = true, .clk_val = U300_SYSCON_SBCER_DMAC_CLK_EN, }, { .type = U300_CLK_TYPE_REST, .id = 5, .hw_ctrld = false, .clk_val = U300_SYSCON_SBCER_EMIF_CLK_EN, }, { .type = U300_CLK_TYPE_REST, .id = 6, .hw_ctrld = false, .clk_val = U300_SYSCON_SBCER_NANDIF_CLK_EN, }, { .type = U300_CLK_TYPE_REST, .id = 8, .hw_ctrld = true, .clk_val = U300_SYSCON_SBCER_XGAM_CLK_EN, }, { .type = U300_CLK_TYPE_REST, .id = 9, .hw_ctrld = false, .clk_val = U300_SYSCON_SBCER_SEMI_CLK_EN, }, { .type = U300_CLK_TYPE_REST, .id = 10, .hw_ctrld = true, .clk_val = U300_SYSCON_SBCER_AHB_SUBSYS_BRIDGE_CLK_EN, }, { .type = U300_CLK_TYPE_REST, .id = 12, .hw_ctrld = false, /* INTCON: cannot be enabled, just taken out of reset */ .clk_val = 0xFFFFU, }, { .type = U300_CLK_TYPE_FAST, .id = 0, .hw_ctrld = true, .clk_val = U300_SYSCON_SBCER_FAST_BRIDGE_CLK_EN, }, { .type = U300_CLK_TYPE_FAST, .id = 1, .hw_ctrld = false, .clk_val = U300_SYSCON_SBCER_I2C0_CLK_EN, }, { .type = U300_CLK_TYPE_FAST, .id = 2, .hw_ctrld = false, .clk_val = U300_SYSCON_SBCER_I2C1_CLK_EN, }, { .type = U300_CLK_TYPE_FAST, .id = 5, .hw_ctrld = false, .clk_val = U300_SYSCON_SBCER_MMC_CLK_EN, }, { .type = U300_CLK_TYPE_FAST, .id = 6, .hw_ctrld = false, .clk_val = U300_SYSCON_SBCER_SPI_CLK_EN, }, { .type = U300_CLK_TYPE_SLOW, .id = 0, .hw_ctrld = true, .clk_val = U300_SYSCON_SBCER_SLOW_BRIDGE_CLK_EN, }, { .type = U300_CLK_TYPE_SLOW, .id = 1, .hw_ctrld = false, .clk_val = U300_SYSCON_SBCER_UART_CLK_EN, }, { .type = U300_CLK_TYPE_SLOW, .id = 4, .hw_ctrld = false, .clk_val = U300_SYSCON_SBCER_GPIO_CLK_EN, }, { .type = U300_CLK_TYPE_SLOW, .id = 6, .hw_ctrld = true, /* No clock enable register bit */ .clk_val = 0xFFFFU, }, { .type = U300_CLK_TYPE_SLOW, .id = 7, .hw_ctrld = false, .clk_val = U300_SYSCON_SBCER_APP_TMR_CLK_EN, }, { .type = U300_CLK_TYPE_SLOW, .id = 8, .hw_ctrld = false, .clk_val = U300_SYSCON_SBCER_ACC_TMR_CLK_EN, }, }; static void __init of_u300_syscon_clk_init(struct device_node *np) { struct clk_hw *hw = ERR_PTR(-EINVAL); const char *clk_name = np->name; const char *parent_name; void __iomem *res_reg; void __iomem *en_reg; u32 clk_type; u32 clk_id; int i; if (of_property_read_u32(np, "clock-type", &clk_type)) { pr_err("%s: syscon clock \"%s\" missing clock-type property\n", __func__, clk_name); return; } if (of_property_read_u32(np, "clock-id", &clk_id)) { pr_err("%s: syscon clock \"%s\" missing clock-id property\n", __func__, clk_name); return; } parent_name = of_clk_get_parent_name(np, 0); switch (clk_type) { case U300_CLK_TYPE_SLOW: res_reg = syscon_vbase + U300_SYSCON_RSR; en_reg = syscon_vbase + U300_SYSCON_CESR; break; case U300_CLK_TYPE_FAST: res_reg = syscon_vbase + U300_SYSCON_RFR; en_reg = syscon_vbase + U300_SYSCON_CEFR; break; case U300_CLK_TYPE_REST: res_reg = syscon_vbase + U300_SYSCON_RRR; en_reg = syscon_vbase + U300_SYSCON_CERR; break; default: pr_err("unknown clock type %x specified\n", clk_type); return; } for (i = 0; i < ARRAY_SIZE(u300_clk_lookup); i++) { const struct u300_clock *u3clk = &u300_clk_lookup[i]; if (u3clk->type == clk_type && u3clk->id == clk_id) hw = syscon_clk_register(NULL, clk_name, parent_name, 0, u3clk->hw_ctrld, res_reg, u3clk->id, en_reg, u3clk->id, u3clk->clk_val); } if (!IS_ERR(hw)) { of_clk_add_hw_provider(np, of_clk_hw_simple_get, hw); /* * Some few system clocks - device tree does not * represent clocks without a corresponding device node. * for now we add these three clocks here. */ if (clk_type == U300_CLK_TYPE_REST && clk_id == 5) clk_hw_register_clkdev(hw, NULL, "pl172"); if (clk_type == U300_CLK_TYPE_REST && clk_id == 9) clk_hw_register_clkdev(hw, NULL, "semi"); if (clk_type == U300_CLK_TYPE_REST && clk_id == 12) clk_hw_register_clkdev(hw, NULL, "intcon"); } } /** * struct clk_mclk - U300 MCLK clock (MMC/SD clock) * @hw: corresponding clock hardware entry * @is_mspro: if this is the memory stick clock rather than MMC/SD */ struct clk_mclk { struct clk_hw hw; bool is_mspro; }; #define to_mclk(_hw) container_of(_hw, struct clk_mclk, hw) static int mclk_clk_prepare(struct clk_hw *hw) { struct clk_mclk *mclk = to_mclk(hw); u16 val; /* The MMC and MSPRO clocks need some special set-up */ if (!mclk->is_mspro) { /* Set default MMC clock divisor to 18.9 MHz */ writew(0x0054U, syscon_vbase + U300_SYSCON_MMF0R); val = readw(syscon_vbase + U300_SYSCON_MMCR); /* Disable the MMC feedback clock */ val &= ~U300_SYSCON_MMCR_MMC_FB_CLK_SEL_ENABLE; /* Disable MSPRO frequency */ val &= ~U300_SYSCON_MMCR_MSPRO_FREQSEL_ENABLE; writew(val, syscon_vbase + U300_SYSCON_MMCR); } else { val = readw(syscon_vbase + U300_SYSCON_MMCR); /* Disable the MMC feedback clock */ val &= ~U300_SYSCON_MMCR_MMC_FB_CLK_SEL_ENABLE; /* Enable MSPRO frequency */ val |= U300_SYSCON_MMCR_MSPRO_FREQSEL_ENABLE; writew(val, syscon_vbase + U300_SYSCON_MMCR); } return 0; } static unsigned long mclk_clk_recalc_rate(struct clk_hw *hw, unsigned long parent_rate) { u16 perf = syscon_get_perf(); switch (perf) { case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW_POWER: /* * Here, the 208 MHz PLL gets shut down and the always * on 13 MHz PLL used for RTC etc kicks into use * instead. */ return 13000000; case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW: case U300_SYSCON_CCR_CLKING_PERFORMANCE_INTERMEDIATE: case U300_SYSCON_CCR_CLKING_PERFORMANCE_HIGH: case U300_SYSCON_CCR_CLKING_PERFORMANCE_BEST: { /* * This clock is under program control. The register is * divided in two nybbles, bit 7-4 gives cycles-1 to count * high, bit 3-0 gives cycles-1 to count low. Distribute * these with no more than 1 cycle difference between * low and high and add low and high to get the actual * divisor. The base PLL is 208 MHz. Writing 0x00 will * divide by 1 and 1 so the highest frequency possible * is 104 MHz. * * e.g. 0x54 => * f = 208 / ((5+1) + (4+1)) = 208 / 11 = 18.9 MHz */ u16 val = readw(syscon_vbase + U300_SYSCON_MMF0R) & U300_SYSCON_MMF0R_MASK; switch (val) { case 0x0054: return 18900000; case 0x0044: return 20800000; case 0x0043: return 23100000; case 0x0033: return 26000000; case 0x0032: return 29700000; case 0x0022: return 34700000; case 0x0021: return 41600000; case 0x0011: return 52000000; case 0x0000: return 104000000; default: break; } } default: break; } return parent_rate; } static long mclk_clk_round_rate(struct clk_hw *hw, unsigned long rate, unsigned long *prate) { if (rate <= 18900000) return 18900000; if (rate <= 20800000) return 20800000; if (rate <= 23100000) return 23100000; if (rate <= 26000000) return 26000000; if (rate <= 29700000) return 29700000; if (rate <= 34700000) return 34700000; if (rate <= 41600000) return 41600000; /* Highest rate */ return 52000000; } static int mclk_clk_set_rate(struct clk_hw *hw, unsigned long rate, unsigned long parent_rate) { u16 val; u16 reg; switch (rate) { case 18900000: val = 0x0054; break; case 20800000: val = 0x0044; break; case 23100000: val = 0x0043; break; case 26000000: val = 0x0033; break; case 29700000: val = 0x0032; break; case 34700000: val = 0x0022; break; case 41600000: val = 0x0021; break; case 52000000: val = 0x0011; break; case 104000000: val = 0x0000; break; default: return -EINVAL; } reg = readw(syscon_vbase + U300_SYSCON_MMF0R) & ~U300_SYSCON_MMF0R_MASK; writew(reg | val, syscon_vbase + U300_SYSCON_MMF0R); return 0; } static const struct clk_ops mclk_ops = { .prepare = mclk_clk_prepare, .recalc_rate = mclk_clk_recalc_rate, .round_rate = mclk_clk_round_rate, .set_rate = mclk_clk_set_rate, }; static struct clk_hw * __init mclk_clk_register(struct device *dev, const char *name, const char *parent_name, bool is_mspro) { struct clk_hw *hw; struct clk_mclk *mclk; struct clk_init_data init = {}; int ret; mclk = kzalloc(sizeof(*mclk), GFP_KERNEL); if (!mclk) return ERR_PTR(-ENOMEM); init.name = "mclk"; init.ops = &mclk_ops; init.flags = 0; init.parent_names = (parent_name ? &parent_name : NULL); init.num_parents = (parent_name ? 1 : 0); mclk->hw.init = &init; mclk->is_mspro = is_mspro; hw = &mclk->hw; ret = clk_hw_register(dev, hw); if (ret) { kfree(mclk); hw = ERR_PTR(ret); } return hw; } static void __init of_u300_syscon_mclk_init(struct device_node *np) { struct clk_hw *hw; const char *clk_name = np->name; const char *parent_name; parent_name = of_clk_get_parent_name(np, 0); hw = mclk_clk_register(NULL, clk_name, parent_name, false); if (!IS_ERR(hw)) of_clk_add_hw_provider(np, of_clk_hw_simple_get, hw); } static const struct of_device_id u300_clk_match[] __initconst = { { .compatible = "fixed-clock", .data = of_fixed_clk_setup, }, { .compatible = "fixed-factor-clock", .data = of_fixed_factor_clk_setup, }, { .compatible = "stericsson,u300-syscon-clk", .data = of_u300_syscon_clk_init, }, { .compatible = "stericsson,u300-syscon-mclk", .data = of_u300_syscon_mclk_init, }, {} }; void __init u300_clk_init(void __iomem *base) { u16 val; syscon_vbase = base; /* Set system to run at PLL208, max performance, a known state. */ val = readw(syscon_vbase + U300_SYSCON_CCR); val &= ~U300_SYSCON_CCR_CLKING_PERFORMANCE_MASK; writew(val, syscon_vbase + U300_SYSCON_CCR); /* Wait for the PLL208 to lock if not locked in yet */ while (!(readw(syscon_vbase + U300_SYSCON_CSR) & U300_SYSCON_CSR_PLL208_LOCK_IND)); /* Power management enable */ val = readw(syscon_vbase + U300_SYSCON_PMCR); val |= U300_SYSCON_PMCR_PWR_MGNT_ENABLE; writew(val, syscon_vbase + U300_SYSCON_PMCR); of_clk_init(u300_clk_match); }