84 lines
2.4 KiB
Plaintext
84 lines
2.4 KiB
Plaintext
* STMicroelectronics STM32 DMA controller
|
|
|
|
The STM32 DMA is a general-purpose direct memory access controller capable of
|
|
supporting 8 independent DMA channels. Each channel can have up to 8 requests.
|
|
|
|
Required properties:
|
|
- compatible: Should be "st,stm32-dma"
|
|
- reg: Should contain DMA registers location and length. This should include
|
|
all of the per-channel registers.
|
|
- interrupts: Should contain all of the per-channel DMA interrupts in
|
|
ascending order with respect to the DMA channel index.
|
|
- clocks: Should contain the input clock of the DMA instance.
|
|
- #dma-cells : Must be <4>. See DMA client paragraph for more details.
|
|
|
|
Optional properties:
|
|
- dma-requests : Number of DMA requests supported.
|
|
- resets: Reference to a reset controller asserting the DMA controller
|
|
- st,mem2mem: boolean; if defined, it indicates that the controller supports
|
|
memory-to-memory transfer
|
|
|
|
Example:
|
|
|
|
dma2: dma-controller@40026400 {
|
|
compatible = "st,stm32-dma";
|
|
reg = <0x40026400 0x400>;
|
|
interrupts = <56>,
|
|
<57>,
|
|
<58>,
|
|
<59>,
|
|
<60>,
|
|
<68>,
|
|
<69>,
|
|
<70>;
|
|
clocks = <&clk_hclk>;
|
|
#dma-cells = <4>;
|
|
st,mem2mem;
|
|
resets = <&rcc 150>;
|
|
dma-requests = <8>;
|
|
};
|
|
|
|
* DMA client
|
|
|
|
DMA clients connected to the STM32 DMA controller must use the format
|
|
described in the dma.txt file, using a four-cell specifier for each
|
|
channel: a phandle to the DMA controller plus the following four integer cells:
|
|
|
|
1. The channel id
|
|
2. The request line number
|
|
3. A 32bit mask specifying the DMA channel configuration which are device
|
|
dependent:
|
|
-bit 9: Peripheral Increment Address
|
|
0x0: no address increment between transfers
|
|
0x1: increment address between transfers
|
|
-bit 10: Memory Increment Address
|
|
0x0: no address increment between transfers
|
|
0x1: increment address between transfers
|
|
-bit 15: Peripheral Increment Offset Size
|
|
0x0: offset size is linked to the peripheral bus width
|
|
0x1: offset size is fixed to 4 (32-bit alignment)
|
|
-bit 16-17: Priority level
|
|
0x0: low
|
|
0x1: medium
|
|
0x2: high
|
|
0x3: very high
|
|
4. A 32bit bitfield value specifying DMA features which are device dependent:
|
|
-bit 0-1: DMA FIFO threshold selection
|
|
0x0: 1/4 full FIFO
|
|
0x1: 1/2 full FIFO
|
|
0x2: 3/4 full FIFO
|
|
0x3: full FIFO
|
|
|
|
|
|
Example:
|
|
|
|
usart1: serial@40011000 {
|
|
compatible = "st,stm32-uart";
|
|
reg = <0x40011000 0x400>;
|
|
interrupts = <37>;
|
|
clocks = <&clk_pclk2>;
|
|
dmas = <&dma2 2 4 0x10400 0x3>,
|
|
<&dma2 7 5 0x10200 0x3>;
|
|
dma-names = "rx", "tx";
|
|
};
|