63 lines
2.8 KiB
Plaintext
63 lines
2.8 KiB
Plaintext
Generic vcpu interface
|
|
====================================
|
|
|
|
The virtual cpu "device" also accepts the ioctls KVM_SET_DEVICE_ATTR,
|
|
KVM_GET_DEVICE_ATTR, and KVM_HAS_DEVICE_ATTR. The interface uses the same struct
|
|
kvm_device_attr as other devices, but targets VCPU-wide settings and controls.
|
|
|
|
The groups and attributes per virtual cpu, if any, are architecture specific.
|
|
|
|
1. GROUP: KVM_ARM_VCPU_PMU_V3_CTRL
|
|
Architectures: ARM64
|
|
|
|
1.1. ATTRIBUTE: KVM_ARM_VCPU_PMU_V3_IRQ
|
|
Parameters: in kvm_device_attr.addr the address for PMU overflow interrupt is a
|
|
pointer to an int
|
|
Returns: -EBUSY: The PMU overflow interrupt is already set
|
|
-ENXIO: The overflow interrupt not set when attempting to get it
|
|
-ENODEV: PMUv3 not supported
|
|
-EINVAL: Invalid PMU overflow interrupt number supplied or
|
|
trying to set the IRQ number without using an in-kernel
|
|
irqchip.
|
|
|
|
A value describing the PMUv3 (Performance Monitor Unit v3) overflow interrupt
|
|
number for this vcpu. This interrupt could be a PPI or SPI, but the interrupt
|
|
type must be same for each vcpu. As a PPI, the interrupt number is the same for
|
|
all vcpus, while as an SPI it must be a separate number per vcpu.
|
|
|
|
1.2 ATTRIBUTE: KVM_ARM_VCPU_PMU_V3_INIT
|
|
Parameters: no additional parameter in kvm_device_attr.addr
|
|
Returns: -ENODEV: PMUv3 not supported or GIC not initialized
|
|
-ENXIO: PMUv3 not properly configured or in-kernel irqchip not
|
|
configured as required prior to calling this attribute
|
|
-EBUSY: PMUv3 already initialized
|
|
|
|
Request the initialization of the PMUv3. If using the PMUv3 with an in-kernel
|
|
virtual GIC implementation, this must be done after initializing the in-kernel
|
|
irqchip.
|
|
|
|
|
|
2. GROUP: KVM_ARM_VCPU_TIMER_CTRL
|
|
Architectures: ARM,ARM64
|
|
|
|
2.1. ATTRIBUTE: KVM_ARM_VCPU_TIMER_IRQ_VTIMER
|
|
2.2. ATTRIBUTE: KVM_ARM_VCPU_TIMER_IRQ_PTIMER
|
|
Parameters: in kvm_device_attr.addr the address for the timer interrupt is a
|
|
pointer to an int
|
|
Returns: -EINVAL: Invalid timer interrupt number
|
|
-EBUSY: One or more VCPUs has already run
|
|
|
|
A value describing the architected timer interrupt number when connected to an
|
|
in-kernel virtual GIC. These must be a PPI (16 <= intid < 32). Setting the
|
|
attribute overrides the default values (see below).
|
|
|
|
KVM_ARM_VCPU_TIMER_IRQ_VTIMER: The EL1 virtual timer intid (default: 27)
|
|
KVM_ARM_VCPU_TIMER_IRQ_PTIMER: The EL1 physical timer intid (default: 30)
|
|
|
|
Setting the same PPI for different timers will prevent the VCPUs from running.
|
|
Setting the interrupt number on a VCPU configures all VCPUs created at that
|
|
time to use the number provided for a given timer, overwriting any previously
|
|
configured values on other VCPUs. Userspace should configure the interrupt
|
|
numbers on at least one VCPU after creating all VCPUs and before running any
|
|
VCPUs.
|