6db4831e98
Android 14
1661 lines
53 KiB
C
1661 lines
53 KiB
C
// SPDX-License-Identifier: GPL-2.0
|
|
/*
|
|
* Copyright (c) 2017, The Linux Foundation. All rights reserved.
|
|
*/
|
|
|
|
#include <linux/clk.h>
|
|
#include <linux/clk-provider.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/err.h>
|
|
#include <linux/io.h>
|
|
#include <linux/iopoll.h>
|
|
#include <linux/kernel.h>
|
|
#include <linux/module.h>
|
|
#include <linux/of.h>
|
|
#include <linux/of_device.h>
|
|
#include <linux/of_address.h>
|
|
#include <linux/phy/phy.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/regulator/consumer.h>
|
|
#include <linux/reset.h>
|
|
#include <linux/slab.h>
|
|
|
|
#include <dt-bindings/phy/phy.h>
|
|
|
|
#include "phy-qcom-qmp.h"
|
|
|
|
/* QPHY_SW_RESET bit */
|
|
#define SW_RESET BIT(0)
|
|
/* QPHY_POWER_DOWN_CONTROL */
|
|
#define SW_PWRDN BIT(0)
|
|
#define REFCLK_DRV_DSBL BIT(1)
|
|
/* QPHY_START_CONTROL bits */
|
|
#define SERDES_START BIT(0)
|
|
#define PCS_START BIT(1)
|
|
#define PLL_READY_GATE_EN BIT(3)
|
|
/* QPHY_PCS_STATUS bit */
|
|
#define PHYSTATUS BIT(6)
|
|
/* QPHY_COM_PCS_READY_STATUS bit */
|
|
#define PCS_READY BIT(0)
|
|
|
|
/* QPHY_V3_DP_COM_RESET_OVRD_CTRL register bits */
|
|
/* DP PHY soft reset */
|
|
#define SW_DPPHY_RESET BIT(0)
|
|
/* mux to select DP PHY reset control, 0:HW control, 1: software reset */
|
|
#define SW_DPPHY_RESET_MUX BIT(1)
|
|
/* USB3 PHY soft reset */
|
|
#define SW_USB3PHY_RESET BIT(2)
|
|
/* mux to select USB3 PHY reset control, 0:HW control, 1: software reset */
|
|
#define SW_USB3PHY_RESET_MUX BIT(3)
|
|
|
|
/* QPHY_V3_DP_COM_PHY_MODE_CTRL register bits */
|
|
#define USB3_MODE BIT(0) /* enables USB3 mode */
|
|
#define DP_MODE BIT(1) /* enables DP mode */
|
|
|
|
/* QPHY_PCS_AUTONOMOUS_MODE_CTRL register bits */
|
|
#define ARCVR_DTCT_EN BIT(0)
|
|
#define ALFPS_DTCT_EN BIT(1)
|
|
#define ARCVR_DTCT_EVENT_SEL BIT(4)
|
|
|
|
/* QPHY_PCS_LFPS_RXTERM_IRQ_CLEAR register bits */
|
|
#define IRQ_CLEAR BIT(0)
|
|
|
|
/* QPHY_PCS_LFPS_RXTERM_IRQ_STATUS register bits */
|
|
#define RCVR_DETECT BIT(0)
|
|
|
|
/* QPHY_V3_PCS_MISC_CLAMP_ENABLE register bits */
|
|
#define CLAMP_EN BIT(0) /* enables i/o clamp_n */
|
|
|
|
#define PHY_INIT_COMPLETE_TIMEOUT 10000
|
|
#define POWER_DOWN_DELAY_US_MIN 10
|
|
#define POWER_DOWN_DELAY_US_MAX 11
|
|
|
|
#define MAX_PROP_NAME 32
|
|
|
|
struct qmp_phy_init_tbl {
|
|
unsigned int offset;
|
|
unsigned int val;
|
|
/*
|
|
* register part of layout ?
|
|
* if yes, then offset gives index in the reg-layout
|
|
*/
|
|
int in_layout;
|
|
};
|
|
|
|
#define QMP_PHY_INIT_CFG(o, v) \
|
|
{ \
|
|
.offset = o, \
|
|
.val = v, \
|
|
}
|
|
|
|
#define QMP_PHY_INIT_CFG_L(o, v) \
|
|
{ \
|
|
.offset = o, \
|
|
.val = v, \
|
|
.in_layout = 1, \
|
|
}
|
|
|
|
/* set of registers with offsets different per-PHY */
|
|
enum qphy_reg_layout {
|
|
/* Common block control registers */
|
|
QPHY_COM_SW_RESET,
|
|
QPHY_COM_POWER_DOWN_CONTROL,
|
|
QPHY_COM_START_CONTROL,
|
|
QPHY_COM_PCS_READY_STATUS,
|
|
/* PCS registers */
|
|
QPHY_PLL_LOCK_CHK_DLY_TIME,
|
|
QPHY_FLL_CNTRL1,
|
|
QPHY_FLL_CNTRL2,
|
|
QPHY_FLL_CNT_VAL_L,
|
|
QPHY_FLL_CNT_VAL_H_TOL,
|
|
QPHY_FLL_MAN_CODE,
|
|
QPHY_SW_RESET,
|
|
QPHY_START_CTRL,
|
|
QPHY_PCS_READY_STATUS,
|
|
QPHY_PCS_AUTONOMOUS_MODE_CTRL,
|
|
QPHY_PCS_LFPS_RXTERM_IRQ_CLEAR,
|
|
QPHY_PCS_LFPS_RXTERM_IRQ_STATUS,
|
|
};
|
|
|
|
static const unsigned int pciephy_regs_layout[] = {
|
|
[QPHY_COM_SW_RESET] = 0x400,
|
|
[QPHY_COM_POWER_DOWN_CONTROL] = 0x404,
|
|
[QPHY_COM_START_CONTROL] = 0x408,
|
|
[QPHY_COM_PCS_READY_STATUS] = 0x448,
|
|
[QPHY_PLL_LOCK_CHK_DLY_TIME] = 0xa8,
|
|
[QPHY_FLL_CNTRL1] = 0xc4,
|
|
[QPHY_FLL_CNTRL2] = 0xc8,
|
|
[QPHY_FLL_CNT_VAL_L] = 0xcc,
|
|
[QPHY_FLL_CNT_VAL_H_TOL] = 0xd0,
|
|
[QPHY_FLL_MAN_CODE] = 0xd4,
|
|
[QPHY_SW_RESET] = 0x00,
|
|
[QPHY_START_CTRL] = 0x08,
|
|
[QPHY_PCS_READY_STATUS] = 0x174,
|
|
};
|
|
|
|
static const unsigned int usb3phy_regs_layout[] = {
|
|
[QPHY_FLL_CNTRL1] = 0xc0,
|
|
[QPHY_FLL_CNTRL2] = 0xc4,
|
|
[QPHY_FLL_CNT_VAL_L] = 0xc8,
|
|
[QPHY_FLL_CNT_VAL_H_TOL] = 0xcc,
|
|
[QPHY_FLL_MAN_CODE] = 0xd0,
|
|
[QPHY_SW_RESET] = 0x00,
|
|
[QPHY_START_CTRL] = 0x08,
|
|
[QPHY_PCS_READY_STATUS] = 0x17c,
|
|
[QPHY_PCS_AUTONOMOUS_MODE_CTRL] = 0x0d4,
|
|
[QPHY_PCS_LFPS_RXTERM_IRQ_CLEAR] = 0x0d8,
|
|
[QPHY_PCS_LFPS_RXTERM_IRQ_STATUS] = 0x178,
|
|
};
|
|
|
|
static const unsigned int qmp_v3_usb3phy_regs_layout[] = {
|
|
[QPHY_SW_RESET] = 0x00,
|
|
[QPHY_START_CTRL] = 0x08,
|
|
[QPHY_PCS_READY_STATUS] = 0x174,
|
|
[QPHY_PCS_AUTONOMOUS_MODE_CTRL] = 0x0d8,
|
|
[QPHY_PCS_LFPS_RXTERM_IRQ_CLEAR] = 0x0dc,
|
|
[QPHY_PCS_LFPS_RXTERM_IRQ_STATUS] = 0x170,
|
|
};
|
|
|
|
static const struct qmp_phy_init_tbl msm8996_pcie_serdes_tbl[] = {
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_BIAS_EN_CLKBUFLR_EN, 0x1c),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_CLK_ENABLE1, 0x10),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_CLK_SELECT, 0x33),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_CMN_CONFIG, 0x06),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP_EN, 0x42),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE_MAP, 0x00),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE_TIMER1, 0xff),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE_TIMER2, 0x1f),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_HSCLK_SEL, 0x01),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_SVS_MODE_CLK_SEL, 0x01),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_CORE_CLK_EN, 0x00),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_CORECLK_DIV, 0x0a),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_BG_TIMER, 0x09),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_DEC_START_MODE0, 0x82),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START3_MODE0, 0x03),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START2_MODE0, 0x55),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START1_MODE0, 0x55),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP3_MODE0, 0x00),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP2_MODE0, 0x1a),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP1_MODE0, 0x0a),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_CLK_SELECT, 0x33),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_SYS_CLK_CTRL, 0x02),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_SYSCLK_BUF_ENABLE, 0x1f),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_SYSCLK_EN_SEL, 0x04),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_CP_CTRL_MODE0, 0x0b),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_PLL_RCTRL_MODE0, 0x16),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_PLL_CCTRL_MODE0, 0x28),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_INTEGLOOP_GAIN1_MODE0, 0x00),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_INTEGLOOP_GAIN0_MODE0, 0x80),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_SSC_EN_CENTER, 0x01),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_SSC_PER1, 0x31),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_SSC_PER2, 0x01),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_SSC_ADJ_PER1, 0x02),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_SSC_ADJ_PER2, 0x00),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_SSC_STEP_SIZE1, 0x2f),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_SSC_STEP_SIZE2, 0x19),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_RESCODE_DIV_NUM, 0x15),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_BG_TRIM, 0x0f),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_PLL_IVCO, 0x0f),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_CLK_EP_DIV, 0x19),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_CLK_ENABLE1, 0x10),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_HSCLK_SEL, 0x00),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_RESCODE_DIV_NUM, 0x40),
|
|
};
|
|
|
|
static const struct qmp_phy_init_tbl msm8996_pcie_tx_tbl[] = {
|
|
QMP_PHY_INIT_CFG(QSERDES_TX_HIGHZ_TRANSCEIVEREN_BIAS_DRVR_EN, 0x45),
|
|
QMP_PHY_INIT_CFG(QSERDES_TX_LANE_MODE, 0x06),
|
|
};
|
|
|
|
static const struct qmp_phy_init_tbl msm8996_pcie_rx_tbl[] = {
|
|
QMP_PHY_INIT_CFG(QSERDES_RX_SIGDET_ENABLES, 0x1c),
|
|
QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2, 0x01),
|
|
QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL3, 0x00),
|
|
QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL4, 0xdb),
|
|
QMP_PHY_INIT_CFG(QSERDES_RX_RX_BAND, 0x18),
|
|
QMP_PHY_INIT_CFG(QSERDES_RX_UCDR_SO_GAIN, 0x04),
|
|
QMP_PHY_INIT_CFG(QSERDES_RX_UCDR_SO_GAIN_HALF, 0x04),
|
|
QMP_PHY_INIT_CFG(QSERDES_RX_UCDR_SO_SATURATION_AND_ENABLE, 0x4b),
|
|
QMP_PHY_INIT_CFG(QSERDES_RX_SIGDET_DEGLITCH_CNTRL, 0x14),
|
|
QMP_PHY_INIT_CFG(QSERDES_RX_SIGDET_LVL, 0x19),
|
|
};
|
|
|
|
static const struct qmp_phy_init_tbl msm8996_pcie_pcs_tbl[] = {
|
|
QMP_PHY_INIT_CFG(QPHY_RX_IDLE_DTCT_CNTRL, 0x4c),
|
|
QMP_PHY_INIT_CFG(QPHY_PWRUP_RESET_DLY_TIME_AUXCLK, 0x00),
|
|
QMP_PHY_INIT_CFG(QPHY_LP_WAKEUP_DLY_TIME_AUXCLK, 0x01),
|
|
|
|
QMP_PHY_INIT_CFG_L(QPHY_PLL_LOCK_CHK_DLY_TIME, 0x05),
|
|
|
|
QMP_PHY_INIT_CFG(QPHY_ENDPOINT_REFCLK_DRIVE, 0x05),
|
|
QMP_PHY_INIT_CFG(QPHY_POWER_DOWN_CONTROL, 0x02),
|
|
QMP_PHY_INIT_CFG(QPHY_POWER_STATE_CONFIG4, 0x00),
|
|
QMP_PHY_INIT_CFG(QPHY_POWER_STATE_CONFIG1, 0xa3),
|
|
QMP_PHY_INIT_CFG(QPHY_TXDEEMPH_M3P5DB_V0, 0x0e),
|
|
};
|
|
|
|
static const struct qmp_phy_init_tbl msm8996_usb3_serdes_tbl[] = {
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_SYSCLK_EN_SEL, 0x14),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_BIAS_EN_CLKBUFLR_EN, 0x08),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_CLK_SELECT, 0x30),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_CMN_CONFIG, 0x06),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_SVS_MODE_CLK_SEL, 0x01),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_HSCLK_SEL, 0x00),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_BG_TRIM, 0x0f),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_PLL_IVCO, 0x0f),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_SYS_CLK_CTRL, 0x04),
|
|
/* PLL and Loop filter settings */
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_DEC_START_MODE0, 0x82),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START1_MODE0, 0x55),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START2_MODE0, 0x55),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START3_MODE0, 0x03),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_CP_CTRL_MODE0, 0x0b),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_PLL_RCTRL_MODE0, 0x16),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_PLL_CCTRL_MODE0, 0x28),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_INTEGLOOP_GAIN0_MODE0, 0x80),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE_CTRL, 0x00),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP1_MODE0, 0x15),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP2_MODE0, 0x34),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP3_MODE0, 0x00),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_CORE_CLK_EN, 0x00),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP_CFG, 0x00),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE_MAP, 0x00),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_BG_TIMER, 0x0a),
|
|
/* SSC settings */
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_SSC_EN_CENTER, 0x01),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_SSC_PER1, 0x31),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_SSC_PER2, 0x01),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_SSC_ADJ_PER1, 0x00),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_SSC_ADJ_PER2, 0x00),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_SSC_STEP_SIZE1, 0xde),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_SSC_STEP_SIZE2, 0x07),
|
|
};
|
|
|
|
static const struct qmp_phy_init_tbl msm8996_usb3_tx_tbl[] = {
|
|
QMP_PHY_INIT_CFG(QSERDES_TX_HIGHZ_TRANSCEIVEREN_BIAS_DRVR_EN, 0x45),
|
|
QMP_PHY_INIT_CFG(QSERDES_TX_RCV_DETECT_LVL_2, 0x12),
|
|
QMP_PHY_INIT_CFG(QSERDES_TX_LANE_MODE, 0x06),
|
|
};
|
|
|
|
static const struct qmp_phy_init_tbl msm8996_usb3_rx_tbl[] = {
|
|
QMP_PHY_INIT_CFG(QSERDES_RX_UCDR_FASTLOCK_FO_GAIN, 0x0b),
|
|
QMP_PHY_INIT_CFG(QSERDES_RX_UCDR_SO_GAIN, 0x04),
|
|
QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2, 0x02),
|
|
QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL3, 0x4c),
|
|
QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL4, 0xbb),
|
|
QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQ_OFFSET_ADAPTOR_CNTRL1, 0x77),
|
|
QMP_PHY_INIT_CFG(QSERDES_RX_RX_OFFSET_ADAPTOR_CNTRL2, 0x80),
|
|
QMP_PHY_INIT_CFG(QSERDES_RX_SIGDET_CNTRL, 0x03),
|
|
QMP_PHY_INIT_CFG(QSERDES_RX_SIGDET_LVL, 0x18),
|
|
QMP_PHY_INIT_CFG(QSERDES_RX_SIGDET_DEGLITCH_CNTRL, 0x16),
|
|
};
|
|
|
|
static const struct qmp_phy_init_tbl msm8996_usb3_pcs_tbl[] = {
|
|
/* FLL settings */
|
|
QMP_PHY_INIT_CFG_L(QPHY_FLL_CNTRL2, 0x03),
|
|
QMP_PHY_INIT_CFG_L(QPHY_FLL_CNTRL1, 0x02),
|
|
QMP_PHY_INIT_CFG_L(QPHY_FLL_CNT_VAL_L, 0x09),
|
|
QMP_PHY_INIT_CFG_L(QPHY_FLL_CNT_VAL_H_TOL, 0x42),
|
|
QMP_PHY_INIT_CFG_L(QPHY_FLL_MAN_CODE, 0x85),
|
|
|
|
/* Lock Det settings */
|
|
QMP_PHY_INIT_CFG(QPHY_LOCK_DETECT_CONFIG1, 0xd1),
|
|
QMP_PHY_INIT_CFG(QPHY_LOCK_DETECT_CONFIG2, 0x1f),
|
|
QMP_PHY_INIT_CFG(QPHY_LOCK_DETECT_CONFIG3, 0x47),
|
|
QMP_PHY_INIT_CFG(QPHY_POWER_STATE_CONFIG2, 0x08),
|
|
};
|
|
|
|
static const struct qmp_phy_init_tbl ipq8074_pcie_serdes_tbl[] = {
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_BIAS_EN_CLKBUFLR_EN, 0x18),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_CLK_ENABLE1, 0x10),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_BG_TRIM, 0xf),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP_EN, 0x1),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE_MAP, 0x0),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE_TIMER1, 0xff),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE_TIMER2, 0x1f),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_CMN_CONFIG, 0x6),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_PLL_IVCO, 0xf),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_HSCLK_SEL, 0x0),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_SVS_MODE_CLK_SEL, 0x1),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_CORE_CLK_EN, 0x20),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_CORECLK_DIV, 0xa),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_RESETSM_CNTRL, 0x20),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_BG_TIMER, 0xa),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_SYSCLK_EN_SEL, 0xa),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_DEC_START_MODE0, 0x82),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START3_MODE0, 0x3),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START2_MODE0, 0x55),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START1_MODE0, 0x55),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP3_MODE0, 0x0),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP2_MODE0, 0xD),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP1_MODE0, 0xD04),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_CLK_SELECT, 0x33),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_SYS_CLK_CTRL, 0x2),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_SYSCLK_BUF_ENABLE, 0x1f),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_CP_CTRL_MODE0, 0xb),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_PLL_RCTRL_MODE0, 0x16),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_PLL_CCTRL_MODE0, 0x28),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_INTEGLOOP_GAIN1_MODE0, 0x0),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_INTEGLOOP_GAIN0_MODE0, 0x80),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_BIAS_EN_CTRL_BY_PSM, 0x1),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_SSC_EN_CENTER, 0x1),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_SSC_PER1, 0x31),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_SSC_PER2, 0x1),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_SSC_ADJ_PER1, 0x2),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_SSC_ADJ_PER2, 0x0),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_SSC_STEP_SIZE1, 0x2f),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_SSC_STEP_SIZE2, 0x19),
|
|
QMP_PHY_INIT_CFG(QSERDES_COM_CLK_EP_DIV, 0x19),
|
|
};
|
|
|
|
static const struct qmp_phy_init_tbl ipq8074_pcie_tx_tbl[] = {
|
|
QMP_PHY_INIT_CFG(QSERDES_TX_HIGHZ_TRANSCEIVEREN_BIAS_DRVR_EN, 0x45),
|
|
QMP_PHY_INIT_CFG(QSERDES_TX_LANE_MODE, 0x6),
|
|
QMP_PHY_INIT_CFG(QSERDES_TX_RES_CODE_LANE_OFFSET, 0x2),
|
|
QMP_PHY_INIT_CFG(QSERDES_TX_RCV_DETECT_LVL_2, 0x12),
|
|
QMP_PHY_INIT_CFG(QSERDES_TX_EMP_POST1_LVL, 0x36),
|
|
QMP_PHY_INIT_CFG(QSERDES_TX_SLEW_CNTL, 0x0a),
|
|
};
|
|
|
|
static const struct qmp_phy_init_tbl ipq8074_pcie_rx_tbl[] = {
|
|
QMP_PHY_INIT_CFG(QSERDES_RX_SIGDET_ENABLES, 0x1c),
|
|
QMP_PHY_INIT_CFG(QSERDES_RX_SIGDET_DEGLITCH_CNTRL, 0x14),
|
|
QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2, 0x1),
|
|
QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL3, 0x0),
|
|
QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL4, 0xdb),
|
|
QMP_PHY_INIT_CFG(QSERDES_RX_UCDR_SO_SATURATION_AND_ENABLE, 0x4b),
|
|
QMP_PHY_INIT_CFG(QSERDES_RX_UCDR_SO_GAIN, 0x4),
|
|
};
|
|
|
|
static const struct qmp_phy_init_tbl ipq8074_pcie_pcs_tbl[] = {
|
|
QMP_PHY_INIT_CFG(QPHY_ENDPOINT_REFCLK_DRIVE, 0x4),
|
|
QMP_PHY_INIT_CFG(QPHY_OSC_DTCT_ACTIONS, 0x0),
|
|
QMP_PHY_INIT_CFG(QPHY_PWRUP_RESET_DLY_TIME_AUXCLK, 0x40),
|
|
QMP_PHY_INIT_CFG(QPHY_L1SS_WAKEUP_DLY_TIME_AUXCLK_MSB, 0x0),
|
|
QMP_PHY_INIT_CFG(QPHY_L1SS_WAKEUP_DLY_TIME_AUXCLK_LSB, 0x40),
|
|
QMP_PHY_INIT_CFG(QPHY_PLL_LOCK_CHK_DLY_TIME_AUXCLK_LSB, 0x0),
|
|
QMP_PHY_INIT_CFG(QPHY_LP_WAKEUP_DLY_TIME_AUXCLK, 0x40),
|
|
QMP_PHY_INIT_CFG_L(QPHY_PLL_LOCK_CHK_DLY_TIME, 0x73),
|
|
QMP_PHY_INIT_CFG(QPHY_RX_SIGDET_LVL, 0x99),
|
|
QMP_PHY_INIT_CFG(QPHY_TXDEEMPH_M6DB_V0, 0x15),
|
|
QMP_PHY_INIT_CFG(QPHY_TXDEEMPH_M3P5DB_V0, 0xe),
|
|
QMP_PHY_INIT_CFG_L(QPHY_SW_RESET, 0x0),
|
|
QMP_PHY_INIT_CFG_L(QPHY_START_CTRL, 0x3),
|
|
};
|
|
|
|
static const struct qmp_phy_init_tbl qmp_v3_usb3_serdes_tbl[] = {
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_PLL_IVCO, 0x07),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_SYSCLK_EN_SEL, 0x14),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_BIAS_EN_CLKBUFLR_EN, 0x08),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_CLK_SELECT, 0x30),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_SYS_CLK_CTRL, 0x02),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_RESETSM_CNTRL2, 0x08),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_CMN_CONFIG, 0x16),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_SVS_MODE_CLK_SEL, 0x01),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_HSCLK_SEL, 0x80),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_DEC_START_MODE0, 0x82),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_DIV_FRAC_START1_MODE0, 0xab),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_DIV_FRAC_START2_MODE0, 0xea),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_DIV_FRAC_START3_MODE0, 0x02),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_CP_CTRL_MODE0, 0x06),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_PLL_RCTRL_MODE0, 0x16),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_PLL_CCTRL_MODE0, 0x36),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_INTEGLOOP_GAIN1_MODE0, 0x00),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_INTEGLOOP_GAIN0_MODE0, 0x3f),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE2_MODE0, 0x01),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE1_MODE0, 0xc9),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_CORECLK_DIV_MODE0, 0x0a),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP3_MODE0, 0x00),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP2_MODE0, 0x34),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP1_MODE0, 0x15),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP_EN, 0x04),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_CORE_CLK_EN, 0x00),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP_CFG, 0x00),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE_MAP, 0x00),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_SYSCLK_BUF_ENABLE, 0x0a),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_EN_CENTER, 0x01),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_PER1, 0x31),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_PER2, 0x01),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_ADJ_PER1, 0x00),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_ADJ_PER2, 0x00),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_STEP_SIZE1, 0x85),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_STEP_SIZE2, 0x07),
|
|
};
|
|
|
|
static const struct qmp_phy_init_tbl qmp_v3_usb3_tx_tbl[] = {
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_TX_HIGHZ_DRVR_EN, 0x10),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_TX_RCV_DETECT_LVL_2, 0x12),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_TX_LANE_MODE_1, 0x16),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_TX_RES_CODE_LANE_OFFSET_RX, 0x09),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_TX_RES_CODE_LANE_OFFSET_TX, 0x06),
|
|
};
|
|
|
|
static const struct qmp_phy_init_tbl qmp_v3_usb3_rx_tbl[] = {
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_FASTLOCK_FO_GAIN, 0x0b),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQU_ADAPTOR_CNTRL2, 0x0f),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQU_ADAPTOR_CNTRL3, 0x4e),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQU_ADAPTOR_CNTRL4, 0x18),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQ_OFFSET_ADAPTOR_CNTRL1, 0x77),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_OFFSET_ADAPTOR_CNTRL2, 0x80),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_RX_SIGDET_CNTRL, 0x03),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_RX_SIGDET_DEGLITCH_CNTRL, 0x16),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_SO_SATURATION_AND_ENABLE, 0x75),
|
|
};
|
|
|
|
static const struct qmp_phy_init_tbl qmp_v3_usb3_pcs_tbl[] = {
|
|
/* FLL settings */
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_FLL_CNTRL2, 0x83),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_FLL_CNT_VAL_L, 0x09),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_FLL_CNT_VAL_H_TOL, 0xa2),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_FLL_MAN_CODE, 0x40),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_FLL_CNTRL1, 0x02),
|
|
|
|
/* Lock Det settings */
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_LOCK_DETECT_CONFIG1, 0xd1),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_LOCK_DETECT_CONFIG2, 0x1f),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_LOCK_DETECT_CONFIG3, 0x47),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_POWER_STATE_CONFIG2, 0x1b),
|
|
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_RX_SIGDET_LVL, 0xba),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_V0, 0x9f),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_V1, 0x9f),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_V2, 0xb7),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_V3, 0x4e),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_V4, 0x65),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_LS, 0x6b),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_V0, 0x15),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_V0, 0x0d),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_V1, 0x15),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_V1, 0x0d),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_V2, 0x15),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_V2, 0x0d),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_V3, 0x15),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_V3, 0x1d),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_V4, 0x15),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_V4, 0x0d),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_LS, 0x15),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_LS, 0x0d),
|
|
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_RATE_SLEW_CNTRL, 0x02),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_PWRUP_RESET_DLY_TIME_AUXCLK, 0x04),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_TSYNC_RSYNC_TIME, 0x44),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_PWRUP_RESET_DLY_TIME_AUXCLK, 0x04),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_RCVR_DTCT_DLY_P1U2_L, 0xe7),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_RCVR_DTCT_DLY_P1U2_H, 0x03),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_RCVR_DTCT_DLY_U3_L, 0x40),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_RCVR_DTCT_DLY_U3_H, 0x00),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_RXEQTRAINING_WAIT_TIME, 0x75),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_LFPS_TX_ECSTART_EQTLOCK, 0x86),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_RXEQTRAINING_RUN_TIME, 0x13),
|
|
};
|
|
|
|
static const struct qmp_phy_init_tbl qmp_v3_usb3_uniphy_serdes_tbl[] = {
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_PLL_IVCO, 0x07),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_SYSCLK_EN_SEL, 0x14),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_BIAS_EN_CLKBUFLR_EN, 0x04),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_CLK_SELECT, 0x30),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_SYS_CLK_CTRL, 0x02),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_RESETSM_CNTRL2, 0x08),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_CMN_CONFIG, 0x06),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_SVS_MODE_CLK_SEL, 0x01),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_HSCLK_SEL, 0x80),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_DEC_START_MODE0, 0x82),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_DIV_FRAC_START1_MODE0, 0xab),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_DIV_FRAC_START2_MODE0, 0xea),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_DIV_FRAC_START3_MODE0, 0x02),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_CP_CTRL_MODE0, 0x06),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_PLL_RCTRL_MODE0, 0x16),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_PLL_CCTRL_MODE0, 0x36),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_INTEGLOOP_GAIN1_MODE0, 0x00),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_INTEGLOOP_GAIN0_MODE0, 0x3f),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE2_MODE0, 0x01),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE1_MODE0, 0xc9),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_CORECLK_DIV_MODE0, 0x0a),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP3_MODE0, 0x00),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP2_MODE0, 0x34),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP1_MODE0, 0x15),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP_EN, 0x04),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_CORE_CLK_EN, 0x00),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP_CFG, 0x00),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE_MAP, 0x00),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_SYSCLK_BUF_ENABLE, 0x0a),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_EN_CENTER, 0x01),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_PER1, 0x31),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_PER2, 0x01),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_ADJ_PER1, 0x00),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_ADJ_PER2, 0x00),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_STEP_SIZE1, 0x85),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_STEP_SIZE2, 0x07),
|
|
};
|
|
|
|
static const struct qmp_phy_init_tbl qmp_v3_usb3_uniphy_tx_tbl[] = {
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_TX_HIGHZ_DRVR_EN, 0x10),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_TX_RCV_DETECT_LVL_2, 0x12),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_TX_LANE_MODE_1, 0xc6),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_TX_RES_CODE_LANE_OFFSET_RX, 0x06),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_TX_RES_CODE_LANE_OFFSET_TX, 0x06),
|
|
};
|
|
|
|
static const struct qmp_phy_init_tbl qmp_v3_usb3_uniphy_rx_tbl[] = {
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_RX_VGA_CAL_CNTRL2, 0x0c),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_MODE_00, 0x50),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_FASTLOCK_FO_GAIN, 0x0b),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQU_ADAPTOR_CNTRL2, 0x0e),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQU_ADAPTOR_CNTRL3, 0x4e),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQU_ADAPTOR_CNTRL4, 0x18),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQ_OFFSET_ADAPTOR_CNTRL1, 0x77),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_OFFSET_ADAPTOR_CNTRL2, 0x80),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_RX_SIGDET_CNTRL, 0x03),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_RX_SIGDET_DEGLITCH_CNTRL, 0x1c),
|
|
QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_SO_SATURATION_AND_ENABLE, 0x75),
|
|
};
|
|
|
|
static const struct qmp_phy_init_tbl qmp_v3_usb3_uniphy_pcs_tbl[] = {
|
|
/* FLL settings */
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_FLL_CNTRL2, 0x83),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_FLL_CNT_VAL_L, 0x09),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_FLL_CNT_VAL_H_TOL, 0xa2),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_FLL_MAN_CODE, 0x40),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_FLL_CNTRL1, 0x02),
|
|
|
|
/* Lock Det settings */
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_LOCK_DETECT_CONFIG1, 0xd1),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_LOCK_DETECT_CONFIG2, 0x1f),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_LOCK_DETECT_CONFIG3, 0x47),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_POWER_STATE_CONFIG2, 0x1b),
|
|
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_RX_SIGDET_LVL, 0xba),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_V0, 0x9f),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_V1, 0x9f),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_V2, 0xb5),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_V3, 0x4c),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_V4, 0x64),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_LS, 0x6a),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_V0, 0x15),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_V0, 0x0d),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_V1, 0x15),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_V1, 0x0d),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_V2, 0x15),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_V2, 0x0d),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_V3, 0x15),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_V3, 0x1d),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_V4, 0x15),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_V4, 0x0d),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_LS, 0x15),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_LS, 0x0d),
|
|
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_RATE_SLEW_CNTRL, 0x02),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_PWRUP_RESET_DLY_TIME_AUXCLK, 0x04),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_TSYNC_RSYNC_TIME, 0x44),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_PWRUP_RESET_DLY_TIME_AUXCLK, 0x04),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_RCVR_DTCT_DLY_P1U2_L, 0xe7),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_RCVR_DTCT_DLY_P1U2_H, 0x03),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_RCVR_DTCT_DLY_U3_L, 0x40),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_RCVR_DTCT_DLY_U3_H, 0x00),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_RXEQTRAINING_WAIT_TIME, 0x75),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_LFPS_TX_ECSTART_EQTLOCK, 0x86),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_RXEQTRAINING_RUN_TIME, 0x13),
|
|
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_REFGEN_REQ_CONFIG1, 0x21),
|
|
QMP_PHY_INIT_CFG(QPHY_V3_PCS_REFGEN_REQ_CONFIG2, 0x60),
|
|
};
|
|
|
|
|
|
/* struct qmp_phy_cfg - per-PHY initialization config */
|
|
struct qmp_phy_cfg {
|
|
/* phy-type - PCIE/UFS/USB */
|
|
unsigned int type;
|
|
/* number of lanes provided by phy */
|
|
int nlanes;
|
|
|
|
/* Init sequence for PHY blocks - serdes, tx, rx, pcs */
|
|
const struct qmp_phy_init_tbl *serdes_tbl;
|
|
int serdes_tbl_num;
|
|
const struct qmp_phy_init_tbl *tx_tbl;
|
|
int tx_tbl_num;
|
|
const struct qmp_phy_init_tbl *rx_tbl;
|
|
int rx_tbl_num;
|
|
const struct qmp_phy_init_tbl *pcs_tbl;
|
|
int pcs_tbl_num;
|
|
|
|
/* clock ids to be requested */
|
|
const char * const *clk_list;
|
|
int num_clks;
|
|
/* resets to be requested */
|
|
const char * const *reset_list;
|
|
int num_resets;
|
|
/* regulators to be requested */
|
|
const char * const *vreg_list;
|
|
int num_vregs;
|
|
|
|
/* array of registers with different offsets */
|
|
const unsigned int *regs;
|
|
|
|
unsigned int start_ctrl;
|
|
unsigned int pwrdn_ctrl;
|
|
unsigned int mask_pcs_ready;
|
|
unsigned int mask_com_pcs_ready;
|
|
|
|
/* true, if PHY has a separate PHY_COM control block */
|
|
bool has_phy_com_ctrl;
|
|
/* true, if PHY has a reset for individual lanes */
|
|
bool has_lane_rst;
|
|
/* true, if PHY needs delay after POWER_DOWN */
|
|
bool has_pwrdn_delay;
|
|
/* power_down delay in usec */
|
|
int pwrdn_delay_min;
|
|
int pwrdn_delay_max;
|
|
|
|
/* true, if PHY has a separate DP_COM control block */
|
|
bool has_phy_dp_com_ctrl;
|
|
/* Register offset of secondary tx/rx lanes for USB DP combo PHY */
|
|
unsigned int tx_b_lane_offset;
|
|
unsigned int rx_b_lane_offset;
|
|
};
|
|
|
|
/**
|
|
* struct qmp_phy - per-lane phy descriptor
|
|
*
|
|
* @phy: generic phy
|
|
* @tx: iomapped memory space for lane's tx
|
|
* @rx: iomapped memory space for lane's rx
|
|
* @pcs: iomapped memory space for lane's pcs
|
|
* @pcs_misc: iomapped memory space for lane's pcs_misc
|
|
* @pipe_clk: pipe lock
|
|
* @index: lane index
|
|
* @qmp: QMP phy to which this lane belongs
|
|
* @lane_rst: lane's reset controller
|
|
*/
|
|
struct qmp_phy {
|
|
struct phy *phy;
|
|
void __iomem *tx;
|
|
void __iomem *rx;
|
|
void __iomem *pcs;
|
|
void __iomem *pcs_misc;
|
|
struct clk *pipe_clk;
|
|
unsigned int index;
|
|
struct qcom_qmp *qmp;
|
|
struct reset_control *lane_rst;
|
|
};
|
|
|
|
/**
|
|
* struct qcom_qmp - structure holding QMP phy block attributes
|
|
*
|
|
* @dev: device
|
|
* @serdes: iomapped memory space for phy's serdes
|
|
* @dp_com: iomapped memory space for phy's dp_com control block
|
|
*
|
|
* @clks: array of clocks required by phy
|
|
* @resets: array of resets required by phy
|
|
* @vregs: regulator supplies bulk data
|
|
*
|
|
* @cfg: phy specific configuration
|
|
* @phys: array of per-lane phy descriptors
|
|
* @phy_mutex: mutex lock for PHY common block initialization
|
|
* @init_count: phy common block initialization count
|
|
* @phy_initialized: indicate if PHY has been initialized
|
|
* @mode: current PHY mode
|
|
*/
|
|
struct qcom_qmp {
|
|
struct device *dev;
|
|
void __iomem *serdes;
|
|
void __iomem *dp_com;
|
|
|
|
struct clk_bulk_data *clks;
|
|
struct reset_control **resets;
|
|
struct regulator_bulk_data *vregs;
|
|
|
|
const struct qmp_phy_cfg *cfg;
|
|
struct qmp_phy **phys;
|
|
|
|
struct mutex phy_mutex;
|
|
int init_count;
|
|
bool phy_initialized;
|
|
enum phy_mode mode;
|
|
};
|
|
|
|
static inline void qphy_setbits(void __iomem *base, u32 offset, u32 val)
|
|
{
|
|
u32 reg;
|
|
|
|
reg = readl(base + offset);
|
|
reg |= val;
|
|
writel(reg, base + offset);
|
|
|
|
/* ensure that above write is through */
|
|
readl(base + offset);
|
|
}
|
|
|
|
static inline void qphy_clrbits(void __iomem *base, u32 offset, u32 val)
|
|
{
|
|
u32 reg;
|
|
|
|
reg = readl(base + offset);
|
|
reg &= ~val;
|
|
writel(reg, base + offset);
|
|
|
|
/* ensure that above write is through */
|
|
readl(base + offset);
|
|
}
|
|
|
|
/* list of clocks required by phy */
|
|
static const char * const msm8996_phy_clk_l[] = {
|
|
"aux", "cfg_ahb", "ref",
|
|
};
|
|
|
|
static const char * const qmp_v3_phy_clk_l[] = {
|
|
"aux", "cfg_ahb", "ref", "com_aux",
|
|
};
|
|
|
|
/* list of resets */
|
|
static const char * const msm8996_pciephy_reset_l[] = {
|
|
"phy", "common", "cfg",
|
|
};
|
|
|
|
static const char * const msm8996_usb3phy_reset_l[] = {
|
|
"phy", "common",
|
|
};
|
|
|
|
/* list of regulators */
|
|
static const char * const msm8996_phy_vreg_l[] = {
|
|
"vdda-phy", "vdda-pll",
|
|
};
|
|
|
|
static const struct qmp_phy_cfg msm8996_pciephy_cfg = {
|
|
.type = PHY_TYPE_PCIE,
|
|
.nlanes = 3,
|
|
|
|
.serdes_tbl = msm8996_pcie_serdes_tbl,
|
|
.serdes_tbl_num = ARRAY_SIZE(msm8996_pcie_serdes_tbl),
|
|
.tx_tbl = msm8996_pcie_tx_tbl,
|
|
.tx_tbl_num = ARRAY_SIZE(msm8996_pcie_tx_tbl),
|
|
.rx_tbl = msm8996_pcie_rx_tbl,
|
|
.rx_tbl_num = ARRAY_SIZE(msm8996_pcie_rx_tbl),
|
|
.pcs_tbl = msm8996_pcie_pcs_tbl,
|
|
.pcs_tbl_num = ARRAY_SIZE(msm8996_pcie_pcs_tbl),
|
|
.clk_list = msm8996_phy_clk_l,
|
|
.num_clks = ARRAY_SIZE(msm8996_phy_clk_l),
|
|
.reset_list = msm8996_pciephy_reset_l,
|
|
.num_resets = ARRAY_SIZE(msm8996_pciephy_reset_l),
|
|
.vreg_list = msm8996_phy_vreg_l,
|
|
.num_vregs = ARRAY_SIZE(msm8996_phy_vreg_l),
|
|
.regs = pciephy_regs_layout,
|
|
|
|
.start_ctrl = PCS_START | PLL_READY_GATE_EN,
|
|
.pwrdn_ctrl = SW_PWRDN | REFCLK_DRV_DSBL,
|
|
.mask_com_pcs_ready = PCS_READY,
|
|
|
|
.has_phy_com_ctrl = true,
|
|
.has_lane_rst = true,
|
|
.has_pwrdn_delay = true,
|
|
.pwrdn_delay_min = POWER_DOWN_DELAY_US_MIN,
|
|
.pwrdn_delay_max = POWER_DOWN_DELAY_US_MAX,
|
|
};
|
|
|
|
static const struct qmp_phy_cfg msm8996_usb3phy_cfg = {
|
|
.type = PHY_TYPE_USB3,
|
|
.nlanes = 1,
|
|
|
|
.serdes_tbl = msm8996_usb3_serdes_tbl,
|
|
.serdes_tbl_num = ARRAY_SIZE(msm8996_usb3_serdes_tbl),
|
|
.tx_tbl = msm8996_usb3_tx_tbl,
|
|
.tx_tbl_num = ARRAY_SIZE(msm8996_usb3_tx_tbl),
|
|
.rx_tbl = msm8996_usb3_rx_tbl,
|
|
.rx_tbl_num = ARRAY_SIZE(msm8996_usb3_rx_tbl),
|
|
.pcs_tbl = msm8996_usb3_pcs_tbl,
|
|
.pcs_tbl_num = ARRAY_SIZE(msm8996_usb3_pcs_tbl),
|
|
.clk_list = msm8996_phy_clk_l,
|
|
.num_clks = ARRAY_SIZE(msm8996_phy_clk_l),
|
|
.reset_list = msm8996_usb3phy_reset_l,
|
|
.num_resets = ARRAY_SIZE(msm8996_usb3phy_reset_l),
|
|
.vreg_list = msm8996_phy_vreg_l,
|
|
.num_vregs = ARRAY_SIZE(msm8996_phy_vreg_l),
|
|
.regs = usb3phy_regs_layout,
|
|
|
|
.start_ctrl = SERDES_START | PCS_START,
|
|
.pwrdn_ctrl = SW_PWRDN,
|
|
.mask_pcs_ready = PHYSTATUS,
|
|
};
|
|
|
|
static const char * const ipq8074_pciephy_clk_l[] = {
|
|
"aux", "cfg_ahb",
|
|
};
|
|
/* list of resets */
|
|
static const char * const ipq8074_pciephy_reset_l[] = {
|
|
"phy", "common",
|
|
};
|
|
|
|
static const struct qmp_phy_cfg ipq8074_pciephy_cfg = {
|
|
.type = PHY_TYPE_PCIE,
|
|
.nlanes = 1,
|
|
|
|
.serdes_tbl = ipq8074_pcie_serdes_tbl,
|
|
.serdes_tbl_num = ARRAY_SIZE(ipq8074_pcie_serdes_tbl),
|
|
.tx_tbl = ipq8074_pcie_tx_tbl,
|
|
.tx_tbl_num = ARRAY_SIZE(ipq8074_pcie_tx_tbl),
|
|
.rx_tbl = ipq8074_pcie_rx_tbl,
|
|
.rx_tbl_num = ARRAY_SIZE(ipq8074_pcie_rx_tbl),
|
|
.pcs_tbl = ipq8074_pcie_pcs_tbl,
|
|
.pcs_tbl_num = ARRAY_SIZE(ipq8074_pcie_pcs_tbl),
|
|
.clk_list = ipq8074_pciephy_clk_l,
|
|
.num_clks = ARRAY_SIZE(ipq8074_pciephy_clk_l),
|
|
.reset_list = ipq8074_pciephy_reset_l,
|
|
.num_resets = ARRAY_SIZE(ipq8074_pciephy_reset_l),
|
|
.vreg_list = NULL,
|
|
.num_vregs = 0,
|
|
.regs = pciephy_regs_layout,
|
|
|
|
.start_ctrl = SERDES_START | PCS_START,
|
|
.pwrdn_ctrl = SW_PWRDN | REFCLK_DRV_DSBL,
|
|
.mask_pcs_ready = PHYSTATUS,
|
|
|
|
.has_phy_com_ctrl = false,
|
|
.has_lane_rst = false,
|
|
.has_pwrdn_delay = true,
|
|
.pwrdn_delay_min = 995, /* us */
|
|
.pwrdn_delay_max = 1005, /* us */
|
|
};
|
|
|
|
static const struct qmp_phy_cfg qmp_v3_usb3phy_cfg = {
|
|
.type = PHY_TYPE_USB3,
|
|
.nlanes = 1,
|
|
|
|
.serdes_tbl = qmp_v3_usb3_serdes_tbl,
|
|
.serdes_tbl_num = ARRAY_SIZE(qmp_v3_usb3_serdes_tbl),
|
|
.tx_tbl = qmp_v3_usb3_tx_tbl,
|
|
.tx_tbl_num = ARRAY_SIZE(qmp_v3_usb3_tx_tbl),
|
|
.rx_tbl = qmp_v3_usb3_rx_tbl,
|
|
.rx_tbl_num = ARRAY_SIZE(qmp_v3_usb3_rx_tbl),
|
|
.pcs_tbl = qmp_v3_usb3_pcs_tbl,
|
|
.pcs_tbl_num = ARRAY_SIZE(qmp_v3_usb3_pcs_tbl),
|
|
.clk_list = qmp_v3_phy_clk_l,
|
|
.num_clks = ARRAY_SIZE(qmp_v3_phy_clk_l),
|
|
.reset_list = msm8996_usb3phy_reset_l,
|
|
.num_resets = ARRAY_SIZE(msm8996_usb3phy_reset_l),
|
|
.vreg_list = msm8996_phy_vreg_l,
|
|
.num_vregs = ARRAY_SIZE(msm8996_phy_vreg_l),
|
|
.regs = qmp_v3_usb3phy_regs_layout,
|
|
|
|
.start_ctrl = SERDES_START | PCS_START,
|
|
.pwrdn_ctrl = SW_PWRDN,
|
|
.mask_pcs_ready = PHYSTATUS,
|
|
|
|
.has_pwrdn_delay = true,
|
|
.pwrdn_delay_min = POWER_DOWN_DELAY_US_MIN,
|
|
.pwrdn_delay_max = POWER_DOWN_DELAY_US_MAX,
|
|
|
|
.has_phy_dp_com_ctrl = true,
|
|
.tx_b_lane_offset = 0x400,
|
|
.rx_b_lane_offset = 0x400,
|
|
};
|
|
|
|
static const struct qmp_phy_cfg qmp_v3_usb3_uniphy_cfg = {
|
|
.type = PHY_TYPE_USB3,
|
|
.nlanes = 1,
|
|
|
|
.serdes_tbl = qmp_v3_usb3_uniphy_serdes_tbl,
|
|
.serdes_tbl_num = ARRAY_SIZE(qmp_v3_usb3_uniphy_serdes_tbl),
|
|
.tx_tbl = qmp_v3_usb3_uniphy_tx_tbl,
|
|
.tx_tbl_num = ARRAY_SIZE(qmp_v3_usb3_uniphy_tx_tbl),
|
|
.rx_tbl = qmp_v3_usb3_uniphy_rx_tbl,
|
|
.rx_tbl_num = ARRAY_SIZE(qmp_v3_usb3_uniphy_rx_tbl),
|
|
.pcs_tbl = qmp_v3_usb3_uniphy_pcs_tbl,
|
|
.pcs_tbl_num = ARRAY_SIZE(qmp_v3_usb3_uniphy_pcs_tbl),
|
|
.clk_list = qmp_v3_phy_clk_l,
|
|
.num_clks = ARRAY_SIZE(qmp_v3_phy_clk_l),
|
|
.reset_list = msm8996_usb3phy_reset_l,
|
|
.num_resets = ARRAY_SIZE(msm8996_usb3phy_reset_l),
|
|
.vreg_list = msm8996_phy_vreg_l,
|
|
.num_vregs = ARRAY_SIZE(msm8996_phy_vreg_l),
|
|
.regs = qmp_v3_usb3phy_regs_layout,
|
|
|
|
.start_ctrl = SERDES_START | PCS_START,
|
|
.pwrdn_ctrl = SW_PWRDN,
|
|
.mask_pcs_ready = PHYSTATUS,
|
|
|
|
.has_pwrdn_delay = true,
|
|
.pwrdn_delay_min = POWER_DOWN_DELAY_US_MIN,
|
|
.pwrdn_delay_max = POWER_DOWN_DELAY_US_MAX,
|
|
};
|
|
|
|
static void qcom_qmp_phy_configure(void __iomem *base,
|
|
const unsigned int *regs,
|
|
const struct qmp_phy_init_tbl tbl[],
|
|
int num)
|
|
{
|
|
int i;
|
|
const struct qmp_phy_init_tbl *t = tbl;
|
|
|
|
if (!t)
|
|
return;
|
|
|
|
for (i = 0; i < num; i++, t++) {
|
|
if (t->in_layout)
|
|
writel(t->val, base + regs[t->offset]);
|
|
else
|
|
writel(t->val, base + t->offset);
|
|
}
|
|
}
|
|
|
|
static int qcom_qmp_phy_com_init(struct qcom_qmp *qmp)
|
|
{
|
|
const struct qmp_phy_cfg *cfg = qmp->cfg;
|
|
void __iomem *serdes = qmp->serdes;
|
|
void __iomem *dp_com = qmp->dp_com;
|
|
int ret, i;
|
|
|
|
mutex_lock(&qmp->phy_mutex);
|
|
if (qmp->init_count++) {
|
|
mutex_unlock(&qmp->phy_mutex);
|
|
return 0;
|
|
}
|
|
|
|
/* turn on regulator supplies */
|
|
ret = regulator_bulk_enable(cfg->num_vregs, qmp->vregs);
|
|
if (ret) {
|
|
dev_err(qmp->dev, "failed to enable regulators, err=%d\n", ret);
|
|
goto err_reg_enable;
|
|
}
|
|
|
|
for (i = 0; i < cfg->num_resets; i++) {
|
|
ret = reset_control_assert(qmp->resets[i]);
|
|
if (ret) {
|
|
dev_err(qmp->dev, "%s reset assert failed\n",
|
|
cfg->reset_list[i]);
|
|
goto err_rst_assert;
|
|
}
|
|
}
|
|
|
|
for (i = cfg->num_resets - 1; i >= 0; i--) {
|
|
ret = reset_control_deassert(qmp->resets[i]);
|
|
if (ret) {
|
|
dev_err(qmp->dev, "%s reset deassert failed\n",
|
|
qmp->cfg->reset_list[i]);
|
|
goto err_rst;
|
|
}
|
|
}
|
|
|
|
ret = clk_bulk_prepare_enable(cfg->num_clks, qmp->clks);
|
|
if (ret) {
|
|
dev_err(qmp->dev, "failed to enable clks, err=%d\n", ret);
|
|
goto err_rst;
|
|
}
|
|
|
|
if (cfg->has_phy_com_ctrl)
|
|
qphy_setbits(serdes, cfg->regs[QPHY_COM_POWER_DOWN_CONTROL],
|
|
SW_PWRDN);
|
|
|
|
if (cfg->has_phy_dp_com_ctrl) {
|
|
qphy_setbits(dp_com, QPHY_V3_DP_COM_POWER_DOWN_CTRL,
|
|
SW_PWRDN);
|
|
/* override hardware control for reset of qmp phy */
|
|
qphy_setbits(dp_com, QPHY_V3_DP_COM_RESET_OVRD_CTRL,
|
|
SW_DPPHY_RESET_MUX | SW_DPPHY_RESET |
|
|
SW_USB3PHY_RESET_MUX | SW_USB3PHY_RESET);
|
|
|
|
qphy_setbits(dp_com, QPHY_V3_DP_COM_PHY_MODE_CTRL,
|
|
USB3_MODE | DP_MODE);
|
|
|
|
/* bring both QMP USB and QMP DP PHYs PCS block out of reset */
|
|
qphy_clrbits(dp_com, QPHY_V3_DP_COM_RESET_OVRD_CTRL,
|
|
SW_DPPHY_RESET_MUX | SW_DPPHY_RESET |
|
|
SW_USB3PHY_RESET_MUX | SW_USB3PHY_RESET);
|
|
}
|
|
|
|
/* Serdes configuration */
|
|
qcom_qmp_phy_configure(serdes, cfg->regs, cfg->serdes_tbl,
|
|
cfg->serdes_tbl_num);
|
|
|
|
if (cfg->has_phy_com_ctrl) {
|
|
void __iomem *status;
|
|
unsigned int mask, val;
|
|
|
|
qphy_clrbits(serdes, cfg->regs[QPHY_COM_SW_RESET], SW_RESET);
|
|
qphy_setbits(serdes, cfg->regs[QPHY_COM_START_CONTROL],
|
|
SERDES_START | PCS_START);
|
|
|
|
status = serdes + cfg->regs[QPHY_COM_PCS_READY_STATUS];
|
|
mask = cfg->mask_com_pcs_ready;
|
|
|
|
ret = readl_poll_timeout(status, val, (val & mask), 10,
|
|
PHY_INIT_COMPLETE_TIMEOUT);
|
|
if (ret) {
|
|
dev_err(qmp->dev,
|
|
"phy common block init timed-out\n");
|
|
goto err_com_init;
|
|
}
|
|
}
|
|
|
|
mutex_unlock(&qmp->phy_mutex);
|
|
|
|
return 0;
|
|
|
|
err_com_init:
|
|
clk_bulk_disable_unprepare(cfg->num_clks, qmp->clks);
|
|
err_rst:
|
|
while (++i < cfg->num_resets)
|
|
reset_control_assert(qmp->resets[i]);
|
|
err_rst_assert:
|
|
regulator_bulk_disable(cfg->num_vregs, qmp->vregs);
|
|
err_reg_enable:
|
|
mutex_unlock(&qmp->phy_mutex);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int qcom_qmp_phy_com_exit(struct qcom_qmp *qmp)
|
|
{
|
|
const struct qmp_phy_cfg *cfg = qmp->cfg;
|
|
void __iomem *serdes = qmp->serdes;
|
|
int i = cfg->num_resets;
|
|
|
|
mutex_lock(&qmp->phy_mutex);
|
|
if (--qmp->init_count) {
|
|
mutex_unlock(&qmp->phy_mutex);
|
|
return 0;
|
|
}
|
|
|
|
if (cfg->has_phy_com_ctrl) {
|
|
qphy_setbits(serdes, cfg->regs[QPHY_COM_START_CONTROL],
|
|
SERDES_START | PCS_START);
|
|
qphy_clrbits(serdes, cfg->regs[QPHY_COM_SW_RESET],
|
|
SW_RESET);
|
|
qphy_setbits(serdes, cfg->regs[QPHY_COM_POWER_DOWN_CONTROL],
|
|
SW_PWRDN);
|
|
}
|
|
|
|
while (--i >= 0)
|
|
reset_control_assert(qmp->resets[i]);
|
|
|
|
clk_bulk_disable_unprepare(cfg->num_clks, qmp->clks);
|
|
|
|
regulator_bulk_disable(cfg->num_vregs, qmp->vregs);
|
|
|
|
mutex_unlock(&qmp->phy_mutex);
|
|
|
|
return 0;
|
|
}
|
|
|
|
/* PHY Initialization */
|
|
static int qcom_qmp_phy_init(struct phy *phy)
|
|
{
|
|
struct qmp_phy *qphy = phy_get_drvdata(phy);
|
|
struct qcom_qmp *qmp = qphy->qmp;
|
|
const struct qmp_phy_cfg *cfg = qmp->cfg;
|
|
void __iomem *tx = qphy->tx;
|
|
void __iomem *rx = qphy->rx;
|
|
void __iomem *pcs = qphy->pcs;
|
|
void __iomem *dp_com = qmp->dp_com;
|
|
void __iomem *status;
|
|
unsigned int mask, val;
|
|
int ret;
|
|
|
|
dev_vdbg(qmp->dev, "Initializing QMP phy\n");
|
|
|
|
ret = qcom_qmp_phy_com_init(qmp);
|
|
if (ret)
|
|
return ret;
|
|
|
|
if (cfg->has_lane_rst) {
|
|
ret = reset_control_deassert(qphy->lane_rst);
|
|
if (ret) {
|
|
dev_err(qmp->dev, "lane%d reset deassert failed\n",
|
|
qphy->index);
|
|
goto err_lane_rst;
|
|
}
|
|
}
|
|
|
|
ret = clk_prepare_enable(qphy->pipe_clk);
|
|
if (ret) {
|
|
dev_err(qmp->dev, "pipe_clk enable failed err=%d\n", ret);
|
|
goto err_clk_enable;
|
|
}
|
|
|
|
/* Tx, Rx, and PCS configurations */
|
|
qcom_qmp_phy_configure(tx, cfg->regs, cfg->tx_tbl, cfg->tx_tbl_num);
|
|
/* Configuration for other LANE for USB-DP combo PHY */
|
|
if (cfg->has_phy_dp_com_ctrl)
|
|
qcom_qmp_phy_configure(tx + cfg->tx_b_lane_offset, cfg->regs,
|
|
cfg->tx_tbl, cfg->tx_tbl_num);
|
|
|
|
qcom_qmp_phy_configure(rx, cfg->regs, cfg->rx_tbl, cfg->rx_tbl_num);
|
|
if (cfg->has_phy_dp_com_ctrl)
|
|
qcom_qmp_phy_configure(rx + cfg->rx_b_lane_offset, cfg->regs,
|
|
cfg->rx_tbl, cfg->rx_tbl_num);
|
|
|
|
qcom_qmp_phy_configure(pcs, cfg->regs, cfg->pcs_tbl, cfg->pcs_tbl_num);
|
|
|
|
/*
|
|
* Pull out PHY from POWER DOWN state.
|
|
* This is active low enable signal to power-down PHY.
|
|
*/
|
|
qphy_setbits(pcs, QPHY_POWER_DOWN_CONTROL, cfg->pwrdn_ctrl);
|
|
|
|
if (cfg->has_pwrdn_delay)
|
|
usleep_range(cfg->pwrdn_delay_min, cfg->pwrdn_delay_max);
|
|
|
|
/* Pull PHY out of reset state */
|
|
qphy_clrbits(pcs, cfg->regs[QPHY_SW_RESET], SW_RESET);
|
|
if (cfg->has_phy_dp_com_ctrl)
|
|
qphy_clrbits(dp_com, QPHY_V3_DP_COM_SW_RESET, SW_RESET);
|
|
|
|
/* start SerDes and Phy-Coding-Sublayer */
|
|
qphy_setbits(pcs, cfg->regs[QPHY_START_CTRL], cfg->start_ctrl);
|
|
|
|
status = pcs + cfg->regs[QPHY_PCS_READY_STATUS];
|
|
mask = cfg->mask_pcs_ready;
|
|
|
|
ret = readl_poll_timeout(status, val, !(val & mask), 1,
|
|
PHY_INIT_COMPLETE_TIMEOUT);
|
|
if (ret) {
|
|
dev_err(qmp->dev, "phy initialization timed-out\n");
|
|
goto err_pcs_ready;
|
|
}
|
|
qmp->phy_initialized = true;
|
|
|
|
return ret;
|
|
|
|
err_pcs_ready:
|
|
clk_disable_unprepare(qphy->pipe_clk);
|
|
err_clk_enable:
|
|
if (cfg->has_lane_rst)
|
|
reset_control_assert(qphy->lane_rst);
|
|
err_lane_rst:
|
|
qcom_qmp_phy_com_exit(qmp);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int qcom_qmp_phy_exit(struct phy *phy)
|
|
{
|
|
struct qmp_phy *qphy = phy_get_drvdata(phy);
|
|
struct qcom_qmp *qmp = qphy->qmp;
|
|
const struct qmp_phy_cfg *cfg = qmp->cfg;
|
|
|
|
clk_disable_unprepare(qphy->pipe_clk);
|
|
|
|
/* PHY reset */
|
|
qphy_setbits(qphy->pcs, cfg->regs[QPHY_SW_RESET], SW_RESET);
|
|
|
|
/* stop SerDes and Phy-Coding-Sublayer */
|
|
qphy_clrbits(qphy->pcs, cfg->regs[QPHY_START_CTRL], cfg->start_ctrl);
|
|
|
|
/* Put PHY into POWER DOWN state: active low */
|
|
qphy_clrbits(qphy->pcs, QPHY_POWER_DOWN_CONTROL, cfg->pwrdn_ctrl);
|
|
|
|
if (cfg->has_lane_rst)
|
|
reset_control_assert(qphy->lane_rst);
|
|
|
|
qcom_qmp_phy_com_exit(qmp);
|
|
|
|
qmp->phy_initialized = false;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int qcom_qmp_phy_set_mode(struct phy *phy,
|
|
enum phy_mode mode, int submode)
|
|
{
|
|
struct qmp_phy *qphy = phy_get_drvdata(phy);
|
|
struct qcom_qmp *qmp = qphy->qmp;
|
|
|
|
qmp->mode = mode;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void qcom_qmp_phy_enable_autonomous_mode(struct qmp_phy *qphy)
|
|
{
|
|
struct qcom_qmp *qmp = qphy->qmp;
|
|
const struct qmp_phy_cfg *cfg = qmp->cfg;
|
|
void __iomem *pcs = qphy->pcs;
|
|
void __iomem *pcs_misc = qphy->pcs_misc;
|
|
u32 intr_mask;
|
|
|
|
if (qmp->mode == PHY_MODE_USB_HOST_SS ||
|
|
qmp->mode == PHY_MODE_USB_DEVICE_SS)
|
|
intr_mask = ARCVR_DTCT_EN | ALFPS_DTCT_EN;
|
|
else
|
|
intr_mask = ARCVR_DTCT_EN | ARCVR_DTCT_EVENT_SEL;
|
|
|
|
/* Clear any pending interrupts status */
|
|
qphy_setbits(pcs, cfg->regs[QPHY_PCS_LFPS_RXTERM_IRQ_CLEAR], IRQ_CLEAR);
|
|
/* Writing 1 followed by 0 clears the interrupt */
|
|
qphy_clrbits(pcs, cfg->regs[QPHY_PCS_LFPS_RXTERM_IRQ_CLEAR], IRQ_CLEAR);
|
|
|
|
qphy_clrbits(pcs, cfg->regs[QPHY_PCS_AUTONOMOUS_MODE_CTRL],
|
|
ARCVR_DTCT_EN | ALFPS_DTCT_EN | ARCVR_DTCT_EVENT_SEL);
|
|
|
|
/* Enable required PHY autonomous mode interrupts */
|
|
qphy_setbits(pcs, cfg->regs[QPHY_PCS_AUTONOMOUS_MODE_CTRL], intr_mask);
|
|
|
|
/* Enable i/o clamp_n for autonomous mode */
|
|
if (pcs_misc)
|
|
qphy_clrbits(pcs_misc, QPHY_V3_PCS_MISC_CLAMP_ENABLE, CLAMP_EN);
|
|
}
|
|
|
|
static void qcom_qmp_phy_disable_autonomous_mode(struct qmp_phy *qphy)
|
|
{
|
|
struct qcom_qmp *qmp = qphy->qmp;
|
|
const struct qmp_phy_cfg *cfg = qmp->cfg;
|
|
void __iomem *pcs = qphy->pcs;
|
|
void __iomem *pcs_misc = qphy->pcs_misc;
|
|
|
|
/* Disable i/o clamp_n on resume for normal mode */
|
|
if (pcs_misc)
|
|
qphy_setbits(pcs_misc, QPHY_V3_PCS_MISC_CLAMP_ENABLE, CLAMP_EN);
|
|
|
|
qphy_clrbits(pcs, cfg->regs[QPHY_PCS_AUTONOMOUS_MODE_CTRL],
|
|
ARCVR_DTCT_EN | ARCVR_DTCT_EVENT_SEL | ALFPS_DTCT_EN);
|
|
|
|
qphy_setbits(pcs, cfg->regs[QPHY_PCS_LFPS_RXTERM_IRQ_CLEAR], IRQ_CLEAR);
|
|
/* Writing 1 followed by 0 clears the interrupt */
|
|
qphy_clrbits(pcs, cfg->regs[QPHY_PCS_LFPS_RXTERM_IRQ_CLEAR], IRQ_CLEAR);
|
|
}
|
|
|
|
static int __maybe_unused qcom_qmp_phy_runtime_suspend(struct device *dev)
|
|
{
|
|
struct qcom_qmp *qmp = dev_get_drvdata(dev);
|
|
struct qmp_phy *qphy = qmp->phys[0];
|
|
const struct qmp_phy_cfg *cfg = qmp->cfg;
|
|
|
|
dev_vdbg(dev, "Suspending QMP phy, mode:%d\n", qmp->mode);
|
|
|
|
/* Supported only for USB3 PHY */
|
|
if (cfg->type != PHY_TYPE_USB3)
|
|
return 0;
|
|
|
|
if (!qmp->phy_initialized) {
|
|
dev_vdbg(dev, "PHY not initialized, bailing out\n");
|
|
return 0;
|
|
}
|
|
|
|
qcom_qmp_phy_enable_autonomous_mode(qphy);
|
|
|
|
clk_disable_unprepare(qphy->pipe_clk);
|
|
clk_bulk_disable_unprepare(cfg->num_clks, qmp->clks);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int __maybe_unused qcom_qmp_phy_runtime_resume(struct device *dev)
|
|
{
|
|
struct qcom_qmp *qmp = dev_get_drvdata(dev);
|
|
struct qmp_phy *qphy = qmp->phys[0];
|
|
const struct qmp_phy_cfg *cfg = qmp->cfg;
|
|
int ret = 0;
|
|
|
|
dev_vdbg(dev, "Resuming QMP phy, mode:%d\n", qmp->mode);
|
|
|
|
/* Supported only for USB3 PHY */
|
|
if (cfg->type != PHY_TYPE_USB3)
|
|
return 0;
|
|
|
|
if (!qmp->phy_initialized) {
|
|
dev_vdbg(dev, "PHY not initialized, bailing out\n");
|
|
return 0;
|
|
}
|
|
|
|
ret = clk_bulk_prepare_enable(cfg->num_clks, qmp->clks);
|
|
if (ret) {
|
|
dev_err(qmp->dev, "failed to enable clks, err=%d\n", ret);
|
|
return ret;
|
|
}
|
|
|
|
ret = clk_prepare_enable(qphy->pipe_clk);
|
|
if (ret) {
|
|
dev_err(dev, "pipe_clk enable failed, err=%d\n", ret);
|
|
clk_bulk_disable_unprepare(cfg->num_clks, qmp->clks);
|
|
return ret;
|
|
}
|
|
|
|
qcom_qmp_phy_disable_autonomous_mode(qphy);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int qcom_qmp_phy_vreg_init(struct device *dev)
|
|
{
|
|
struct qcom_qmp *qmp = dev_get_drvdata(dev);
|
|
int num = qmp->cfg->num_vregs;
|
|
int i;
|
|
|
|
qmp->vregs = devm_kcalloc(dev, num, sizeof(*qmp->vregs), GFP_KERNEL);
|
|
if (!qmp->vregs)
|
|
return -ENOMEM;
|
|
|
|
for (i = 0; i < num; i++)
|
|
qmp->vregs[i].supply = qmp->cfg->vreg_list[i];
|
|
|
|
return devm_regulator_bulk_get(dev, num, qmp->vregs);
|
|
}
|
|
|
|
static int qcom_qmp_phy_reset_init(struct device *dev)
|
|
{
|
|
struct qcom_qmp *qmp = dev_get_drvdata(dev);
|
|
int i;
|
|
|
|
qmp->resets = devm_kcalloc(dev, qmp->cfg->num_resets,
|
|
sizeof(*qmp->resets), GFP_KERNEL);
|
|
if (!qmp->resets)
|
|
return -ENOMEM;
|
|
|
|
for (i = 0; i < qmp->cfg->num_resets; i++) {
|
|
struct reset_control *rst;
|
|
const char *name = qmp->cfg->reset_list[i];
|
|
|
|
rst = devm_reset_control_get(dev, name);
|
|
if (IS_ERR(rst)) {
|
|
dev_err(dev, "failed to get %s reset\n", name);
|
|
return PTR_ERR(rst);
|
|
}
|
|
qmp->resets[i] = rst;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int qcom_qmp_phy_clk_init(struct device *dev)
|
|
{
|
|
struct qcom_qmp *qmp = dev_get_drvdata(dev);
|
|
int num = qmp->cfg->num_clks;
|
|
int i;
|
|
|
|
qmp->clks = devm_kcalloc(dev, num, sizeof(*qmp->clks), GFP_KERNEL);
|
|
if (!qmp->clks)
|
|
return -ENOMEM;
|
|
|
|
for (i = 0; i < num; i++)
|
|
qmp->clks[i].id = qmp->cfg->clk_list[i];
|
|
|
|
return devm_clk_bulk_get(dev, num, qmp->clks);
|
|
}
|
|
|
|
/*
|
|
* Register a fixed rate pipe clock.
|
|
*
|
|
* The <s>_pipe_clksrc generated by PHY goes to the GCC that gate
|
|
* controls it. The <s>_pipe_clk coming out of the GCC is requested
|
|
* by the PHY driver for its operations.
|
|
* We register the <s>_pipe_clksrc here. The gcc driver takes care
|
|
* of assigning this <s>_pipe_clksrc as parent to <s>_pipe_clk.
|
|
* Below picture shows this relationship.
|
|
*
|
|
* +---------------+
|
|
* | PHY block |<<---------------------------------------+
|
|
* | | |
|
|
* | +-------+ | +-----+ |
|
|
* I/P---^-->| PLL |---^--->pipe_clksrc--->| GCC |--->pipe_clk---+
|
|
* clk | +-------+ | +-----+
|
|
* +---------------+
|
|
*/
|
|
static int phy_pipe_clk_register(struct qcom_qmp *qmp, struct device_node *np)
|
|
{
|
|
struct clk_fixed_rate *fixed;
|
|
struct clk_init_data init = { };
|
|
int ret;
|
|
|
|
if ((qmp->cfg->type != PHY_TYPE_USB3) &&
|
|
(qmp->cfg->type != PHY_TYPE_PCIE)) {
|
|
/* not all phys register pipe clocks, so return success */
|
|
return 0;
|
|
}
|
|
|
|
ret = of_property_read_string(np, "clock-output-names", &init.name);
|
|
if (ret) {
|
|
dev_err(qmp->dev, "%s: No clock-output-names\n", np->name);
|
|
return ret;
|
|
}
|
|
|
|
fixed = devm_kzalloc(qmp->dev, sizeof(*fixed), GFP_KERNEL);
|
|
if (!fixed)
|
|
return -ENOMEM;
|
|
|
|
init.ops = &clk_fixed_rate_ops;
|
|
|
|
/* controllers using QMP phys use 125MHz pipe clock interface */
|
|
fixed->fixed_rate = 125000000;
|
|
fixed->hw.init = &init;
|
|
|
|
return devm_clk_hw_register(qmp->dev, &fixed->hw);
|
|
}
|
|
|
|
static const struct phy_ops qcom_qmp_phy_gen_ops = {
|
|
.init = qcom_qmp_phy_init,
|
|
.exit = qcom_qmp_phy_exit,
|
|
.set_mode = qcom_qmp_phy_set_mode,
|
|
.owner = THIS_MODULE,
|
|
};
|
|
|
|
static
|
|
int qcom_qmp_phy_create(struct device *dev, struct device_node *np, int id)
|
|
{
|
|
struct qcom_qmp *qmp = dev_get_drvdata(dev);
|
|
struct phy *generic_phy;
|
|
struct qmp_phy *qphy;
|
|
char prop_name[MAX_PROP_NAME];
|
|
int ret;
|
|
|
|
qphy = devm_kzalloc(dev, sizeof(*qphy), GFP_KERNEL);
|
|
if (!qphy)
|
|
return -ENOMEM;
|
|
|
|
/*
|
|
* Get memory resources for each phy lane:
|
|
* Resources are indexed as: tx -> 0; rx -> 1; pcs -> 2; and
|
|
* pcs_misc (optional) -> 3.
|
|
*/
|
|
qphy->tx = of_iomap(np, 0);
|
|
if (!qphy->tx)
|
|
return -ENOMEM;
|
|
|
|
qphy->rx = of_iomap(np, 1);
|
|
if (!qphy->rx)
|
|
return -ENOMEM;
|
|
|
|
qphy->pcs = of_iomap(np, 2);
|
|
if (!qphy->pcs)
|
|
return -ENOMEM;
|
|
|
|
qphy->pcs_misc = of_iomap(np, 3);
|
|
if (!qphy->pcs_misc)
|
|
dev_vdbg(dev, "PHY pcs_misc-reg not used\n");
|
|
|
|
/*
|
|
* Get PHY's Pipe clock, if any. USB3 and PCIe are PIPE3
|
|
* based phys, so they essentially have pipe clock. So,
|
|
* we return error in case phy is USB3 or PIPE type.
|
|
* Otherwise, we initialize pipe clock to NULL for
|
|
* all phys that don't need this.
|
|
*/
|
|
snprintf(prop_name, sizeof(prop_name), "pipe%d", id);
|
|
qphy->pipe_clk = of_clk_get_by_name(np, prop_name);
|
|
if (IS_ERR(qphy->pipe_clk)) {
|
|
if (qmp->cfg->type == PHY_TYPE_PCIE ||
|
|
qmp->cfg->type == PHY_TYPE_USB3) {
|
|
ret = PTR_ERR(qphy->pipe_clk);
|
|
if (ret != -EPROBE_DEFER)
|
|
dev_err(dev,
|
|
"failed to get lane%d pipe_clk, %d\n",
|
|
id, ret);
|
|
return ret;
|
|
}
|
|
qphy->pipe_clk = NULL;
|
|
}
|
|
|
|
/* Get lane reset, if any */
|
|
if (qmp->cfg->has_lane_rst) {
|
|
snprintf(prop_name, sizeof(prop_name), "lane%d", id);
|
|
qphy->lane_rst = of_reset_control_get(np, prop_name);
|
|
if (IS_ERR(qphy->lane_rst)) {
|
|
dev_err(dev, "failed to get lane%d reset\n", id);
|
|
return PTR_ERR(qphy->lane_rst);
|
|
}
|
|
}
|
|
|
|
generic_phy = devm_phy_create(dev, np, &qcom_qmp_phy_gen_ops);
|
|
if (IS_ERR(generic_phy)) {
|
|
ret = PTR_ERR(generic_phy);
|
|
dev_err(dev, "failed to create qphy %d\n", ret);
|
|
return ret;
|
|
}
|
|
|
|
qphy->phy = generic_phy;
|
|
qphy->index = id;
|
|
qphy->qmp = qmp;
|
|
qmp->phys[id] = qphy;
|
|
phy_set_drvdata(generic_phy, qphy);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static const struct of_device_id qcom_qmp_phy_of_match_table[] = {
|
|
{
|
|
.compatible = "qcom,msm8996-qmp-pcie-phy",
|
|
.data = &msm8996_pciephy_cfg,
|
|
}, {
|
|
.compatible = "qcom,msm8996-qmp-usb3-phy",
|
|
.data = &msm8996_usb3phy_cfg,
|
|
}, {
|
|
.compatible = "qcom,ipq8074-qmp-pcie-phy",
|
|
.data = &ipq8074_pciephy_cfg,
|
|
}, {
|
|
.compatible = "qcom,sdm845-qmp-usb3-phy",
|
|
.data = &qmp_v3_usb3phy_cfg,
|
|
}, {
|
|
.compatible = "qcom,sdm845-qmp-usb3-uni-phy",
|
|
.data = &qmp_v3_usb3_uniphy_cfg,
|
|
},
|
|
{ },
|
|
};
|
|
MODULE_DEVICE_TABLE(of, qcom_qmp_phy_of_match_table);
|
|
|
|
static const struct dev_pm_ops qcom_qmp_phy_pm_ops = {
|
|
SET_RUNTIME_PM_OPS(qcom_qmp_phy_runtime_suspend,
|
|
qcom_qmp_phy_runtime_resume, NULL)
|
|
};
|
|
|
|
static int qcom_qmp_phy_probe(struct platform_device *pdev)
|
|
{
|
|
struct qcom_qmp *qmp;
|
|
struct device *dev = &pdev->dev;
|
|
struct resource *res;
|
|
struct device_node *child;
|
|
struct phy_provider *phy_provider;
|
|
void __iomem *base;
|
|
int num, id;
|
|
int ret;
|
|
|
|
qmp = devm_kzalloc(dev, sizeof(*qmp), GFP_KERNEL);
|
|
if (!qmp)
|
|
return -ENOMEM;
|
|
|
|
qmp->dev = dev;
|
|
dev_set_drvdata(dev, qmp);
|
|
|
|
/* Get the specific init parameters of QMP phy */
|
|
qmp->cfg = of_device_get_match_data(dev);
|
|
if (!qmp->cfg)
|
|
return -EINVAL;
|
|
|
|
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
|
|
base = devm_ioremap_resource(dev, res);
|
|
if (IS_ERR(base))
|
|
return PTR_ERR(base);
|
|
|
|
/* per PHY serdes; usually located at base address */
|
|
qmp->serdes = base;
|
|
|
|
/* per PHY dp_com; if PHY has dp_com control block */
|
|
if (qmp->cfg->has_phy_dp_com_ctrl) {
|
|
res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
|
|
"dp_com");
|
|
base = devm_ioremap_resource(dev, res);
|
|
if (IS_ERR(base))
|
|
return PTR_ERR(base);
|
|
|
|
qmp->dp_com = base;
|
|
}
|
|
|
|
mutex_init(&qmp->phy_mutex);
|
|
|
|
ret = qcom_qmp_phy_clk_init(dev);
|
|
if (ret)
|
|
return ret;
|
|
|
|
ret = qcom_qmp_phy_reset_init(dev);
|
|
if (ret)
|
|
return ret;
|
|
|
|
ret = qcom_qmp_phy_vreg_init(dev);
|
|
if (ret) {
|
|
dev_err(dev, "failed to get regulator supplies\n");
|
|
return ret;
|
|
}
|
|
|
|
num = of_get_available_child_count(dev->of_node);
|
|
/* do we have a rogue child node ? */
|
|
if (num > qmp->cfg->nlanes)
|
|
return -EINVAL;
|
|
|
|
qmp->phys = devm_kcalloc(dev, num, sizeof(*qmp->phys), GFP_KERNEL);
|
|
if (!qmp->phys)
|
|
return -ENOMEM;
|
|
|
|
id = 0;
|
|
pm_runtime_set_active(dev);
|
|
pm_runtime_enable(dev);
|
|
/*
|
|
* Prevent runtime pm from being ON by default. Users can enable
|
|
* it using power/control in sysfs.
|
|
*/
|
|
pm_runtime_forbid(dev);
|
|
|
|
for_each_available_child_of_node(dev->of_node, child) {
|
|
/* Create per-lane phy */
|
|
ret = qcom_qmp_phy_create(dev, child, id);
|
|
if (ret) {
|
|
dev_err(dev, "failed to create lane%d phy, %d\n",
|
|
id, ret);
|
|
pm_runtime_disable(dev);
|
|
return ret;
|
|
}
|
|
|
|
/*
|
|
* Register the pipe clock provided by phy.
|
|
* See function description to see details of this pipe clock.
|
|
*/
|
|
ret = phy_pipe_clk_register(qmp, child);
|
|
if (ret) {
|
|
dev_err(qmp->dev,
|
|
"failed to register pipe clock source\n");
|
|
pm_runtime_disable(dev);
|
|
return ret;
|
|
}
|
|
id++;
|
|
}
|
|
|
|
phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
|
|
if (!IS_ERR(phy_provider))
|
|
dev_info(dev, "Registered Qcom-QMP phy\n");
|
|
else
|
|
pm_runtime_disable(dev);
|
|
|
|
return PTR_ERR_OR_ZERO(phy_provider);
|
|
}
|
|
|
|
static struct platform_driver qcom_qmp_phy_driver = {
|
|
.probe = qcom_qmp_phy_probe,
|
|
.driver = {
|
|
.name = "qcom-qmp-phy",
|
|
.pm = &qcom_qmp_phy_pm_ops,
|
|
.of_match_table = qcom_qmp_phy_of_match_table,
|
|
},
|
|
};
|
|
|
|
module_platform_driver(qcom_qmp_phy_driver);
|
|
|
|
MODULE_AUTHOR("Vivek Gautam <vivek.gautam@codeaurora.org>");
|
|
MODULE_DESCRIPTION("Qualcomm QMP PHY driver");
|
|
MODULE_LICENSE("GPL v2");
|