85 lines
1.9 KiB
Plaintext
85 lines
1.9 KiB
Plaintext
* Marvell International Ltd. NCI NFC Controller
|
|
|
|
Required properties:
|
|
- compatible: Should be:
|
|
- "marvell,nfc-uart" or "mrvl,nfc-uart" for UART devices
|
|
- "marvell,nfc-i2c" for I2C devices
|
|
- "marvell,nfc-spi" for SPI devices
|
|
|
|
Optional SoC specific properties:
|
|
- pinctrl-names: Contains only one value - "default".
|
|
- pintctrl-0: Specifies the pin control groups used for this controller.
|
|
- reset-n-io: Output GPIO pin used to reset the chip (active low).
|
|
- hci-muxed: Specifies that the chip is muxing NCI over HCI frames.
|
|
|
|
Optional UART-based chip specific properties:
|
|
- flow-control: Specifies that the chip is using RTS/CTS.
|
|
- break-control: Specifies that the chip needs specific break management.
|
|
|
|
Optional I2C-based chip specific properties:
|
|
- i2c-int-falling: Specifies that the chip read event shall be trigged on
|
|
falling edge.
|
|
- i2c-int-rising: Specifies that the chip read event shall be trigged on
|
|
rising edge.
|
|
|
|
Example (for ARM-based BeagleBoard Black with 88W8887 on UART5):
|
|
|
|
&uart5 {
|
|
|
|
nfcmrvluart: nfcmrvluart@5 {
|
|
compatible = "marvell,nfc-uart";
|
|
|
|
reset-n-io = <&gpio3 16 0>;
|
|
|
|
hci-muxed;
|
|
flow-control;
|
|
}
|
|
};
|
|
|
|
|
|
Example (for ARM-based BeagleBoard Black with 88W8887 on I2C1):
|
|
|
|
&i2c1 {
|
|
clock-frequency = <400000>;
|
|
|
|
nfcmrvli2c0: i2c@1 {
|
|
compatible = "marvell,nfc-i2c";
|
|
|
|
reg = <0x8>;
|
|
|
|
/* I2C INT configuration */
|
|
interrupt-parent = <&gpio3>;
|
|
interrupts = <21 0>;
|
|
|
|
/* I2C INT trigger configuration */
|
|
i2c-int-rising;
|
|
|
|
/* Reset IO */
|
|
reset-n-io = <&gpio3 19 0>;
|
|
};
|
|
};
|
|
|
|
|
|
Example (for ARM-based BeagleBoard Black on SPI0):
|
|
|
|
&spi0 {
|
|
|
|
mrvlnfcspi0: spi@0 {
|
|
compatible = "marvell,nfc-spi";
|
|
|
|
reg = <0>;
|
|
|
|
/* SPI Bus configuration */
|
|
spi-max-frequency = <3000000>;
|
|
spi-cpha;
|
|
spi-cpol;
|
|
|
|
/* SPI INT configuration */
|
|
interrupt-parent = <&gpio1>;
|
|
interrupts = <17 0>;
|
|
|
|
/* Reset IO */
|
|
reset-n-io = <&gpio3 19 0>;
|
|
};
|
|
};
|