367 lines
9.5 KiB
C
367 lines
9.5 KiB
C
/*
|
|
* SL82C105/Winbond 553 IDE driver
|
|
*
|
|
* Maintainer unknown.
|
|
*
|
|
* Drive tuning added from Rebel.com's kernel sources
|
|
* -- Russell King (15/11/98) linux@arm.linux.org.uk
|
|
*
|
|
* Merge in Russell's HW workarounds, fix various problems
|
|
* with the timing registers setup.
|
|
* -- Benjamin Herrenschmidt (01/11/03) benh@kernel.crashing.org
|
|
*
|
|
* Copyright (C) 2006-2007,2009 MontaVista Software, Inc. <source@mvista.com>
|
|
* Copyright (C) 2007 Bartlomiej Zolnierkiewicz
|
|
*/
|
|
|
|
#include <linux/types.h>
|
|
#include <linux/module.h>
|
|
#include <linux/kernel.h>
|
|
#include <linux/pci.h>
|
|
#include <linux/ide.h>
|
|
|
|
#include <asm/io.h>
|
|
|
|
#define DRV_NAME "sl82c105"
|
|
|
|
/*
|
|
* SL82C105 PCI config register 0x40 bits.
|
|
*/
|
|
#define CTRL_IDE_IRQB (1 << 30)
|
|
#define CTRL_IDE_IRQA (1 << 28)
|
|
#define CTRL_LEGIRQ (1 << 11)
|
|
#define CTRL_P1F16 (1 << 5)
|
|
#define CTRL_P1EN (1 << 4)
|
|
#define CTRL_P0F16 (1 << 1)
|
|
#define CTRL_P0EN (1 << 0)
|
|
|
|
/*
|
|
* Convert a PIO mode and cycle time to the required on/off times
|
|
* for the interface. This has protection against runaway timings.
|
|
*/
|
|
static unsigned int get_pio_timings(ide_drive_t *drive, u8 pio)
|
|
{
|
|
struct ide_timing *t = ide_timing_find_mode(XFER_PIO_0 + pio);
|
|
unsigned int cmd_on, cmd_off;
|
|
u8 iordy = 0;
|
|
|
|
cmd_on = (t->active + 29) / 30;
|
|
cmd_off = (ide_pio_cycle_time(drive, pio) - 30 * cmd_on + 29) / 30;
|
|
|
|
if (cmd_on == 0)
|
|
cmd_on = 1;
|
|
|
|
if (cmd_off == 0)
|
|
cmd_off = 1;
|
|
|
|
if (ide_pio_need_iordy(drive, pio))
|
|
iordy = 0x40;
|
|
|
|
return (cmd_on - 1) << 8 | (cmd_off - 1) | iordy;
|
|
}
|
|
|
|
/*
|
|
* Configure the chipset for PIO mode.
|
|
*/
|
|
static void sl82c105_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
|
|
{
|
|
struct pci_dev *dev = to_pci_dev(hwif->dev);
|
|
unsigned long timings = (unsigned long)ide_get_drivedata(drive);
|
|
int reg = 0x44 + drive->dn * 4;
|
|
u16 drv_ctrl;
|
|
const u8 pio = drive->pio_mode - XFER_PIO_0;
|
|
|
|
drv_ctrl = get_pio_timings(drive, pio);
|
|
|
|
/*
|
|
* Store the PIO timings so that we can restore them
|
|
* in case DMA will be turned off...
|
|
*/
|
|
timings &= 0xffff0000;
|
|
timings |= drv_ctrl;
|
|
ide_set_drivedata(drive, (void *)timings);
|
|
|
|
pci_write_config_word(dev, reg, drv_ctrl);
|
|
pci_read_config_word (dev, reg, &drv_ctrl);
|
|
|
|
printk(KERN_DEBUG "%s: selected %s (%dns) (%04X)\n", drive->name,
|
|
ide_xfer_verbose(pio + XFER_PIO_0),
|
|
ide_pio_cycle_time(drive, pio), drv_ctrl);
|
|
}
|
|
|
|
/*
|
|
* Configure the chipset for DMA mode.
|
|
*/
|
|
static void sl82c105_set_dma_mode(ide_hwif_t *hwif, ide_drive_t *drive)
|
|
{
|
|
static u16 mwdma_timings[] = {0x0707, 0x0201, 0x0200};
|
|
unsigned long timings = (unsigned long)ide_get_drivedata(drive);
|
|
u16 drv_ctrl;
|
|
const u8 speed = drive->dma_mode;
|
|
|
|
drv_ctrl = mwdma_timings[speed - XFER_MW_DMA_0];
|
|
|
|
/*
|
|
* Store the DMA timings so that we can actually program
|
|
* them when DMA will be turned on...
|
|
*/
|
|
timings &= 0x0000ffff;
|
|
timings |= (unsigned long)drv_ctrl << 16;
|
|
ide_set_drivedata(drive, (void *)timings);
|
|
}
|
|
|
|
static int sl82c105_test_irq(ide_hwif_t *hwif)
|
|
{
|
|
struct pci_dev *dev = to_pci_dev(hwif->dev);
|
|
u32 val, mask = hwif->channel ? CTRL_IDE_IRQB : CTRL_IDE_IRQA;
|
|
|
|
pci_read_config_dword(dev, 0x40, &val);
|
|
|
|
return (val & mask) ? 1 : 0;
|
|
}
|
|
|
|
/*
|
|
* The SL82C105 holds off all IDE interrupts while in DMA mode until
|
|
* all DMA activity is completed. Sometimes this causes problems (eg,
|
|
* when the drive wants to report an error condition).
|
|
*
|
|
* 0x7e is a "chip testing" register. Bit 2 resets the DMA controller
|
|
* state machine. We need to kick this to work around various bugs.
|
|
*/
|
|
static inline void sl82c105_reset_host(struct pci_dev *dev)
|
|
{
|
|
u16 val;
|
|
|
|
pci_read_config_word(dev, 0x7e, &val);
|
|
pci_write_config_word(dev, 0x7e, val | (1 << 2));
|
|
pci_write_config_word(dev, 0x7e, val & ~(1 << 2));
|
|
}
|
|
|
|
/*
|
|
* If we get an IRQ timeout, it might be that the DMA state machine
|
|
* got confused. Fix from Todd Inglett. Details from Winbond.
|
|
*
|
|
* This function is called when the IDE timer expires, the drive
|
|
* indicates that it is READY, and we were waiting for DMA to complete.
|
|
*/
|
|
static void sl82c105_dma_lost_irq(ide_drive_t *drive)
|
|
{
|
|
ide_hwif_t *hwif = drive->hwif;
|
|
struct pci_dev *dev = to_pci_dev(hwif->dev);
|
|
u32 val, mask = hwif->channel ? CTRL_IDE_IRQB : CTRL_IDE_IRQA;
|
|
u8 dma_cmd;
|
|
|
|
printk(KERN_WARNING "sl82c105: lost IRQ, resetting host\n");
|
|
|
|
/*
|
|
* Check the raw interrupt from the drive.
|
|
*/
|
|
pci_read_config_dword(dev, 0x40, &val);
|
|
if (val & mask)
|
|
printk(KERN_INFO "sl82c105: drive was requesting IRQ, "
|
|
"but host lost it\n");
|
|
|
|
/*
|
|
* Was DMA enabled? If so, disable it - we're resetting the
|
|
* host. The IDE layer will be handling the drive for us.
|
|
*/
|
|
dma_cmd = inb(hwif->dma_base + ATA_DMA_CMD);
|
|
if (dma_cmd & 1) {
|
|
outb(dma_cmd & ~1, hwif->dma_base + ATA_DMA_CMD);
|
|
printk(KERN_INFO "sl82c105: DMA was enabled\n");
|
|
}
|
|
|
|
sl82c105_reset_host(dev);
|
|
}
|
|
|
|
/*
|
|
* ATAPI devices can cause the SL82C105 DMA state machine to go gaga.
|
|
* Winbond recommend that the DMA state machine is reset prior to
|
|
* setting the bus master DMA enable bit.
|
|
*
|
|
* The generic IDE core will have disabled the BMEN bit before this
|
|
* function is called.
|
|
*/
|
|
static void sl82c105_dma_start(ide_drive_t *drive)
|
|
{
|
|
ide_hwif_t *hwif = drive->hwif;
|
|
struct pci_dev *dev = to_pci_dev(hwif->dev);
|
|
int reg = 0x44 + drive->dn * 4;
|
|
|
|
pci_write_config_word(dev, reg,
|
|
(unsigned long)ide_get_drivedata(drive) >> 16);
|
|
|
|
sl82c105_reset_host(dev);
|
|
ide_dma_start(drive);
|
|
}
|
|
|
|
static void sl82c105_dma_clear(ide_drive_t *drive)
|
|
{
|
|
struct pci_dev *dev = to_pci_dev(drive->hwif->dev);
|
|
|
|
sl82c105_reset_host(dev);
|
|
}
|
|
|
|
static int sl82c105_dma_end(ide_drive_t *drive)
|
|
{
|
|
struct pci_dev *dev = to_pci_dev(drive->hwif->dev);
|
|
int reg = 0x44 + drive->dn * 4;
|
|
int ret = ide_dma_end(drive);
|
|
|
|
pci_write_config_word(dev, reg,
|
|
(unsigned long)ide_get_drivedata(drive));
|
|
|
|
return ret;
|
|
}
|
|
|
|
/*
|
|
* ATA reset will clear the 16 bits mode in the control
|
|
* register, we need to reprogram it
|
|
*/
|
|
static void sl82c105_resetproc(ide_drive_t *drive)
|
|
{
|
|
struct pci_dev *dev = to_pci_dev(drive->hwif->dev);
|
|
u32 val;
|
|
|
|
pci_read_config_dword(dev, 0x40, &val);
|
|
val |= (CTRL_P1F16 | CTRL_P0F16);
|
|
pci_write_config_dword(dev, 0x40, val);
|
|
}
|
|
|
|
/*
|
|
* Return the revision of the Winbond bridge
|
|
* which this function is part of.
|
|
*/
|
|
static u8 sl82c105_bridge_revision(struct pci_dev *dev)
|
|
{
|
|
struct pci_dev *bridge;
|
|
|
|
/*
|
|
* The bridge should be part of the same device, but function 0.
|
|
*/
|
|
bridge = pci_get_domain_bus_and_slot(pci_domain_nr(dev->bus),
|
|
dev->bus->number,
|
|
PCI_DEVFN(PCI_SLOT(dev->devfn), 0));
|
|
if (!bridge)
|
|
return -1;
|
|
|
|
/*
|
|
* Make sure it is a Winbond 553 and is an ISA bridge.
|
|
*/
|
|
if (bridge->vendor != PCI_VENDOR_ID_WINBOND ||
|
|
bridge->device != PCI_DEVICE_ID_WINBOND_83C553 ||
|
|
bridge->class >> 8 != PCI_CLASS_BRIDGE_ISA) {
|
|
pci_dev_put(bridge);
|
|
return -1;
|
|
}
|
|
/*
|
|
* We need to find function 0's revision, not function 1
|
|
*/
|
|
pci_dev_put(bridge);
|
|
|
|
return bridge->revision;
|
|
}
|
|
|
|
/*
|
|
* Enable the PCI device
|
|
*
|
|
* --BenH: It's arch fixup code that should enable channels that
|
|
* have not been enabled by firmware. I decided we can still enable
|
|
* channel 0 here at least, but channel 1 has to be enabled by
|
|
* firmware or arch code. We still set both to 16 bits mode.
|
|
*/
|
|
static int init_chipset_sl82c105(struct pci_dev *dev)
|
|
{
|
|
u32 val;
|
|
|
|
pci_read_config_dword(dev, 0x40, &val);
|
|
val |= CTRL_P0EN | CTRL_P0F16 | CTRL_P1F16;
|
|
pci_write_config_dword(dev, 0x40, val);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static const struct ide_port_ops sl82c105_port_ops = {
|
|
.set_pio_mode = sl82c105_set_pio_mode,
|
|
.set_dma_mode = sl82c105_set_dma_mode,
|
|
.resetproc = sl82c105_resetproc,
|
|
.test_irq = sl82c105_test_irq,
|
|
};
|
|
|
|
static const struct ide_dma_ops sl82c105_dma_ops = {
|
|
.dma_host_set = ide_dma_host_set,
|
|
.dma_setup = ide_dma_setup,
|
|
.dma_start = sl82c105_dma_start,
|
|
.dma_end = sl82c105_dma_end,
|
|
.dma_test_irq = ide_dma_test_irq,
|
|
.dma_lost_irq = sl82c105_dma_lost_irq,
|
|
.dma_timer_expiry = ide_dma_sff_timer_expiry,
|
|
.dma_clear = sl82c105_dma_clear,
|
|
.dma_sff_read_status = ide_dma_sff_read_status,
|
|
};
|
|
|
|
static const struct ide_port_info sl82c105_chipset = {
|
|
.name = DRV_NAME,
|
|
.init_chipset = init_chipset_sl82c105,
|
|
.enablebits = {{0x40,0x01,0x01}, {0x40,0x10,0x10}},
|
|
.port_ops = &sl82c105_port_ops,
|
|
.dma_ops = &sl82c105_dma_ops,
|
|
.host_flags = IDE_HFLAG_IO_32BIT |
|
|
IDE_HFLAG_UNMASK_IRQS |
|
|
IDE_HFLAG_SERIALIZE_DMA |
|
|
IDE_HFLAG_NO_AUTODMA,
|
|
.pio_mask = ATA_PIO5,
|
|
.mwdma_mask = ATA_MWDMA2,
|
|
};
|
|
|
|
static int sl82c105_init_one(struct pci_dev *dev, const struct pci_device_id *id)
|
|
{
|
|
struct ide_port_info d = sl82c105_chipset;
|
|
u8 rev = sl82c105_bridge_revision(dev);
|
|
|
|
if (rev <= 5) {
|
|
/*
|
|
* Never ever EVER under any circumstances enable
|
|
* DMA when the bridge is this old.
|
|
*/
|
|
printk(KERN_INFO DRV_NAME ": Winbond W83C553 bridge "
|
|
"revision %d, BM-DMA disabled\n", rev);
|
|
d.dma_ops = NULL;
|
|
d.mwdma_mask = 0;
|
|
d.host_flags &= ~IDE_HFLAG_SERIALIZE_DMA;
|
|
}
|
|
|
|
return ide_pci_init_one(dev, &d, NULL);
|
|
}
|
|
|
|
static const struct pci_device_id sl82c105_pci_tbl[] = {
|
|
{ PCI_VDEVICE(WINBOND, PCI_DEVICE_ID_WINBOND_82C105), 0 },
|
|
{ 0, },
|
|
};
|
|
MODULE_DEVICE_TABLE(pci, sl82c105_pci_tbl);
|
|
|
|
static struct pci_driver sl82c105_pci_driver = {
|
|
.name = "W82C105_IDE",
|
|
.id_table = sl82c105_pci_tbl,
|
|
.probe = sl82c105_init_one,
|
|
.remove = ide_pci_remove,
|
|
.suspend = ide_pci_suspend,
|
|
.resume = ide_pci_resume,
|
|
};
|
|
|
|
static int __init sl82c105_ide_init(void)
|
|
{
|
|
return ide_pci_register_driver(&sl82c105_pci_driver);
|
|
}
|
|
|
|
static void __exit sl82c105_ide_exit(void)
|
|
{
|
|
pci_unregister_driver(&sl82c105_pci_driver);
|
|
}
|
|
|
|
module_init(sl82c105_ide_init);
|
|
module_exit(sl82c105_ide_exit);
|
|
|
|
MODULE_DESCRIPTION("PCI driver module for W82C105 IDE");
|
|
MODULE_LICENSE("GPL");
|