89 lines
3.2 KiB
Plaintext
Executable file
89 lines
3.2 KiB
Plaintext
Executable file
STMicroelectronics STi c8sectpfe binding
|
|
============================================
|
|
|
|
This document describes the c8sectpfe device bindings that is used to get transport
|
|
stream data into the SoC on the TS pins, and into DDR for further processing.
|
|
|
|
It is typically used in conjunction with one or more demodulator and tuner devices
|
|
which converts from the RF to digital domain. Demodulators and tuners are usually
|
|
located on an external DVB frontend card connected to SoC TS input pins.
|
|
|
|
Currently 7 TS input (tsin) channels are supported on the stih407 family SoC.
|
|
|
|
Required properties (controller (parent) node):
|
|
- compatible : Should be "stih407-c8sectpfe"
|
|
|
|
- reg : Address and length of register sets for each device in
|
|
"reg-names"
|
|
|
|
- reg-names : The names of the register addresses corresponding to the
|
|
registers filled in "reg":
|
|
- c8sectpfe: c8sectpfe registers
|
|
- c8sectpfe-ram: c8sectpfe internal sram
|
|
|
|
- clocks : phandle list of c8sectpfe clocks
|
|
- clock-names : should be "c8sectpfe"
|
|
See: Documentation/devicetree/bindings/clock/clock-bindings.txt
|
|
|
|
- pinctrl-names : a pinctrl state named tsin%d-serial or tsin%d-parallel (where %d is tsin-num)
|
|
must be defined for each tsin child node.
|
|
- pinctrl-0 : phandle referencing pin configuration for this tsin configuration
|
|
See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
|
|
|
|
|
|
Required properties (tsin (child) node):
|
|
|
|
- tsin-num : tsin id of the InputBlock (must be between 0 to 6)
|
|
- i2c-bus : phandle to the I2C bus DT node which the demodulators & tuners on this tsin channel are connected.
|
|
- reset-gpios : reset gpio for this tsin channel.
|
|
|
|
Optional properties (tsin (child) node):
|
|
|
|
- invert-ts-clk : Bool property to control sense of ts input clock (data stored on falling edge of clk).
|
|
- serial-not-parallel : Bool property to configure input bus width (serial on ts_data<7>).
|
|
- async-not-sync : Bool property to control if data is received in asynchronous mode
|
|
(all bits/bytes with ts_valid or ts_packet asserted are valid).
|
|
|
|
- dvb-card : Describes the NIM card connected to this tsin channel.
|
|
|
|
Example:
|
|
|
|
/* stih410 SoC b2120 + b2004a + stv0367-pll(NIMB) + stv0367-tda18212 (NIMA) DT example) */
|
|
|
|
c8sectpfe@8a20000 {
|
|
compatible = "st,stih407-c8sectpfe";
|
|
reg = <0x08a20000 0x10000>, <0x08a00000 0x4000>;
|
|
reg-names = "stfe", "stfe-ram";
|
|
interrupts = <GIC_SPI 34 IRQ_TYPE_NONE>, <GIC_SPI 35 IRQ_TYPE_NONE>;
|
|
interrupt-names = "stfe-error-irq", "stfe-idle-irq";
|
|
pinctrl-0 = <&pinctrl_tsin0_serial>;
|
|
pinctrl-1 = <&pinctrl_tsin0_parallel>;
|
|
pinctrl-2 = <&pinctrl_tsin3_serial>;
|
|
pinctrl-3 = <&pinctrl_tsin4_serial_alt3>;
|
|
pinctrl-4 = <&pinctrl_tsin5_serial_alt1>;
|
|
pinctrl-names = "tsin0-serial",
|
|
"tsin0-parallel",
|
|
"tsin3-serial",
|
|
"tsin4-serial",
|
|
"tsin5-serial";
|
|
clocks = <&clk_s_c0_flexgen CLK_PROC_STFE>;
|
|
clock-names = "c8sectpfe";
|
|
|
|
/* tsin0 is TSA on NIMA */
|
|
tsin0: port@0 {
|
|
tsin-num = <0>;
|
|
serial-not-parallel;
|
|
i2c-bus = <&ssc2>;
|
|
reset-gpios = <&pio15 4 GPIO_ACTIVE_HIGH>;
|
|
dvb-card = <STV0367_TDA18212_NIMA_1>;
|
|
};
|
|
|
|
tsin3: port@3 {
|
|
tsin-num = <3>;
|
|
serial-not-parallel;
|
|
i2c-bus = <&ssc3>;
|
|
reset-gpios = <&pio15 7 GPIO_ACTIVE_HIGH>;
|
|
dvb-card = <STV0367_TDA18212_NIMB_1>;
|
|
};
|
|
};
|