80 lines
2.9 KiB
Plaintext
Executable file
80 lines
2.9 KiB
Plaintext
Executable file
SAMSUNG Exynos SoCs SROM Controller driver.
|
|
|
|
Required properties:
|
|
- compatible : Should contain "samsung,exynos4210-srom".
|
|
|
|
- reg: offset and length of the register set
|
|
|
|
Optional properties:
|
|
The SROM controller can be used to attach external peripherals. In this case
|
|
extra properties, describing the bus behind it, should be specified as below:
|
|
|
|
- #address-cells: Must be set to 2 to allow device address translation.
|
|
Address is specified as (bank#, offset).
|
|
|
|
- #size-cells: Must be set to 1 to allow device size passing
|
|
|
|
- ranges: Must be set up to reflect the memory layout with four integer values
|
|
per bank:
|
|
<bank-number> 0 <parent address of bank> <size>
|
|
|
|
Sub-nodes:
|
|
The actual device nodes should be added as subnodes to the SROMc node. These
|
|
subnodes, in addition to regular device specification, should contain the following
|
|
properties, describing configuration of the relevant SROM bank:
|
|
|
|
Required properties:
|
|
- reg: bank number, base address (relative to start of the bank) and size of
|
|
the memory mapped for the device. Note that base address will be
|
|
typically 0 as this is the start of the bank.
|
|
|
|
- samsung,srom-timing : array of 6 integers, specifying bank timings in the
|
|
following order: Tacp, Tcah, Tcoh, Tacc, Tcos, Tacs.
|
|
Each value is specified in cycles and has the following
|
|
meaning and valid range:
|
|
Tacp : Page mode access cycle at Page mode (0 - 15)
|
|
Tcah : Address holding time after CSn (0 - 15)
|
|
Tcoh : Chip selection hold on OEn (0 - 15)
|
|
Tacc : Access cycle (0 - 31, the actual time is N + 1)
|
|
Tcos : Chip selection set-up before OEn (0 - 15)
|
|
Tacs : Address set-up before CSn (0 - 15)
|
|
|
|
Optional properties:
|
|
- reg-io-width : data width in bytes (1 or 2). If omitted, default of 1 is used.
|
|
|
|
- samsung,srom-page-mode : if page mode is set, 4 data page mode will be configured,
|
|
else normal (1 data) page mode will be set.
|
|
|
|
Example: basic definition, no banks are configured
|
|
memory-controller@12570000 {
|
|
compatible = "samsung,exynos4210-srom";
|
|
reg = <0x12570000 0x14>;
|
|
};
|
|
|
|
Example: SROMc with SMSC911x ethernet chip on bank 3
|
|
memory-controller@12570000 {
|
|
#address-cells = <2>;
|
|
#size-cells = <1>;
|
|
ranges = <0 0 0x04000000 0x20000 // Bank0
|
|
1 0 0x05000000 0x20000 // Bank1
|
|
2 0 0x06000000 0x20000 // Bank2
|
|
3 0 0x07000000 0x20000>; // Bank3
|
|
|
|
compatible = "samsung,exynos4210-srom";
|
|
reg = <0x12570000 0x14>;
|
|
|
|
ethernet@3,0 {
|
|
compatible = "smsc,lan9115";
|
|
reg = <3 0 0x10000>; // Bank 3, offset = 0
|
|
phy-mode = "mii";
|
|
interrupt-parent = <&gpx0>;
|
|
interrupts = <5 8>;
|
|
reg-io-width = <2>;
|
|
smsc,irq-push-pull;
|
|
smsc,force-internal-phy;
|
|
|
|
samsung,srom-page-mode;
|
|
samsung,srom-timing = <9 12 1 9 1 1>;
|
|
};
|
|
};
|