61 lines
2.3 KiB
Plaintext
Executable file
61 lines
2.3 KiB
Plaintext
Executable file
ST Microelectronics Flexible Static Memory Controller (FSMC)
|
|
NAND Interface
|
|
|
|
Required properties:
|
|
- compatible : "st,spear600-fsmc-nand", "stericsson,fsmc-nand"
|
|
- reg : Address range of the mtd chip
|
|
- reg-names: Should contain the reg names "fsmc_regs", "nand_data", "nand_addr" and "nand_cmd"
|
|
|
|
Optional properties:
|
|
- bank-width : Width (in bytes) of the device. If not present, the width
|
|
defaults to 1 byte
|
|
- nand-skip-bbtscan: Indicates the BBT scanning should be skipped
|
|
- timings: array of 6 bytes for NAND timings. The meanings of these bytes
|
|
are:
|
|
byte 0 TCLR : CLE to RE delay in number of AHB clock cycles, only 4 bits
|
|
are valid. Zero means one clockcycle, 15 means 16 clock
|
|
cycles.
|
|
byte 1 TAR : ALE to RE delay, 4 bits are valid. Same format as TCLR.
|
|
byte 2 THIZ : number of HCLK clock cycles during which the data bus is
|
|
kept in Hi-Z (tristate) after the start of a write access.
|
|
Only valid for write transactions. Zero means zero cycles,
|
|
255 means 255 cycles.
|
|
byte 3 THOLD : number of HCLK clock cycles to hold the address (and data
|
|
when writing) after the command deassertation. Zero means
|
|
one cycle, 255 means 256 cycles.
|
|
byte 4 TWAIT : number of HCLK clock cycles to assert the command to the
|
|
NAND flash in response to SMWAITn. Zero means 1 cycle,
|
|
255 means 256 cycles.
|
|
byte 5 TSET : number of HCLK clock cycles to assert the address before the
|
|
command is asserted. Zero means one cycle, 255 means 256
|
|
cycles.
|
|
- bank: default NAND bank to use (0-3 are valid, 0 is the default).
|
|
- nand-ecc-mode : see nand.txt
|
|
- nand-ecc-strength : see nand.txt
|
|
- nand-ecc-step-size : see nand.txt
|
|
|
|
Can support 1-bit HW ECC (default) or if stronger correction is required,
|
|
software-based BCH.
|
|
|
|
Example:
|
|
|
|
fsmc: flash@d1800000 {
|
|
compatible = "st,spear600-fsmc-nand";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
reg = <0xd1800000 0x1000 /* FSMC Register */
|
|
0xd2000000 0x0010 /* NAND Base DATA */
|
|
0xd2020000 0x0010 /* NAND Base ADDR */
|
|
0xd2010000 0x0010>; /* NAND Base CMD */
|
|
reg-names = "fsmc_regs", "nand_data", "nand_addr", "nand_cmd";
|
|
|
|
bank-width = <1>;
|
|
nand-skip-bbtscan;
|
|
timings = /bits/ 8 <0 0 0 2 3 0>;
|
|
bank = <1>;
|
|
|
|
partition@0 {
|
|
...
|
|
};
|
|
};
|