75 lines
3.7 KiB
Plaintext
Executable file
75 lines
3.7 KiB
Plaintext
Executable file
Tegra SOC USB PHY
|
|
|
|
The device node for Tegra SOC USB PHY:
|
|
|
|
Required properties :
|
|
- compatible : For Tegra20, must contain "nvidia,tegra20-usb-phy".
|
|
For Tegra30, must contain "nvidia,tegra30-usb-phy". Otherwise, must contain
|
|
"nvidia,<chip>-usb-phy" plus at least one of the above, where <chip> is
|
|
tegra114, tegra124, tegra132, or tegra210.
|
|
- reg : Defines the following set of registers, in the order listed:
|
|
- The PHY's own register set.
|
|
Always present.
|
|
- The register set of the PHY containing the UTMI pad control registers.
|
|
Present if-and-only-if phy_type == utmi.
|
|
- phy_type : Should be one of "utmi", "ulpi" or "hsic".
|
|
- clocks : Defines the clocks listed in the clock-names property.
|
|
- clock-names : The following clock names must be present:
|
|
- reg: The clock needed to access the PHY's own registers. This is the
|
|
associated EHCI controller's clock. Always present.
|
|
- pll_u: PLL_U. Always present.
|
|
- timer: The timeout clock (clk_m). Present if phy_type == utmi.
|
|
- utmi-pads: The clock needed to access the UTMI pad control registers.
|
|
Present if phy_type == utmi.
|
|
- ulpi-link: The clock Tegra provides to the ULPI PHY (usually pad DAP_MCLK2
|
|
with pad group aka "nvidia,pins" cdev2 and pin mux option config aka
|
|
"nvidia,function" pllp_out4).
|
|
Present if phy_type == ulpi, and ULPI link mode is in use.
|
|
- resets : Must contain an entry for each entry in reset-names.
|
|
See ../reset/reset.txt for details.
|
|
- reset-names : Must include the following entries:
|
|
- usb: The PHY's own reset signal.
|
|
- utmi-pads: The reset of the PHY containing the chip-wide UTMI pad control
|
|
registers. Required even if phy_type == ulpi.
|
|
|
|
Required properties for phy_type == ulpi:
|
|
- nvidia,phy-reset-gpio : The GPIO used to reset the PHY.
|
|
|
|
Required PHY timing params for utmi phy, for all chips:
|
|
- nvidia,hssync-start-delay : Number of 480 Mhz clock cycles to wait before
|
|
start of sync launches RxActive
|
|
- nvidia,elastic-limit : Variable FIFO Depth of elastic input store
|
|
- nvidia,idle-wait-delay : Number of 480 Mhz clock cycles of idle to wait
|
|
before declare IDLE.
|
|
- nvidia,term-range-adj : Range adjusment on terminations
|
|
- Either one of the following for HS driver output control:
|
|
- nvidia,xcvr-setup : integer, uses the provided value.
|
|
- nvidia,xcvr-setup-use-fuses : boolean, indicates that the value is read
|
|
from the on-chip fuses
|
|
If both are provided, nvidia,xcvr-setup-use-fuses takes precedence.
|
|
- nvidia,xcvr-lsfslew : LS falling slew rate control.
|
|
- nvidia,xcvr-lsrslew : LS rising slew rate control.
|
|
|
|
Required PHY timing params for utmi phy, only on Tegra30 and above:
|
|
- nvidia,xcvr-hsslew : HS slew rate control.
|
|
- nvidia,hssquelch-level : HS squelch detector level.
|
|
- nvidia,hsdiscon-level : HS disconnect detector level.
|
|
|
|
Optional properties:
|
|
- nvidia,has-legacy-mode : boolean indicates whether this controller can
|
|
operate in legacy mode (as APX 2500 / 2600). In legacy mode some
|
|
registers are accessed through the APB_MISC base address instead of
|
|
the USB controller.
|
|
- nvidia,is-wired : boolean. Indicates whether we can do certain kind of power
|
|
optimizations for the devices that are always connected. e.g. modem.
|
|
- dr_mode : dual role mode. Indicates the working mode for the PHY. Can be
|
|
"host", "peripheral", or "otg". Defaults to "host" if not defined.
|
|
host means this is a host controller
|
|
peripheral means it is device controller
|
|
otg means it can operate as either ("on the go")
|
|
- nvidia,has-utmi-pad-registers : boolean indicates whether this controller
|
|
contains the UTMI pad control registers common to all USB controllers.
|
|
|
|
VBUS control (required for dr_mode == otg, optional for dr_mode == host):
|
|
- vbus-supply: regulator for VBUS
|