104 lines
3.5 KiB
Plaintext
Executable file
104 lines
3.5 KiB
Plaintext
Executable file
Qualcomm SuperSpeed DWC3 USB SoC controller
|
|
|
|
Required properties:
|
|
- compatible: Compatible list, contains
|
|
"qcom,dwc3"
|
|
"qcom,msm8996-dwc3" for msm8996 SOC.
|
|
"qcom,sdm845-dwc3" for sdm845 SOC.
|
|
- reg: Offset and length of register set for QSCRATCH wrapper
|
|
- power-domains: specifies a phandle to PM domain provider node
|
|
- clocks: A list of phandle + clock-specifier pairs for the
|
|
clocks listed in clock-names
|
|
- clock-names: Should contain the following:
|
|
"core" Master/Core clock, have to be >= 125 MHz for SS
|
|
operation and >= 60MHz for HS operation
|
|
"mock_utmi" Mock utmi clock needed for ITP/SOF generation in
|
|
host mode. Its frequency should be 19.2MHz.
|
|
"sleep" Sleep clock, used for wakeup when USB3 core goes
|
|
into low power mode (U3).
|
|
|
|
Optional clocks:
|
|
"iface" System bus AXI clock.
|
|
Not present on "qcom,msm8996-dwc3" compatible.
|
|
"cfg_noc" System Config NOC clock.
|
|
Not present on "qcom,msm8996-dwc3" compatible.
|
|
- assigned-clocks: Should be:
|
|
MOCK_UTMI_CLK
|
|
MASTER_CLK
|
|
- assigned-clock-rates: Should be:
|
|
19.2Mhz (192000000) for MOCK_UTMI_CLK
|
|
>=125Mhz (125000000) for MASTER_CLK in SS mode
|
|
>=60Mhz (60000000) for MASTER_CLK in HS mode
|
|
|
|
Optional properties:
|
|
- resets: Phandle to reset control that resets core and wrapper.
|
|
- interrupts: specifies interrupts from controller wrapper used
|
|
to wakeup from low power/susepnd state. Must contain
|
|
one or more entry for interrupt-names property
|
|
- interrupt-names: Must include the following entries:
|
|
- "hs_phy_irq": The interrupt that is asserted when a
|
|
wakeup event is received on USB2 bus
|
|
- "ss_phy_irq": The interrupt that is asserted when a
|
|
wakeup event is received on USB3 bus
|
|
- "dm_hs_phy_irq" and "dp_hs_phy_irq": Separate
|
|
interrupts for any wakeup event on DM and DP lines
|
|
- qcom,select-utmi-as-pipe-clk: if present, disable USB3 pipe_clk requirement.
|
|
Used when dwc3 operates without SSPHY and only
|
|
HS/FS/LS modes are supported.
|
|
|
|
Required child node:
|
|
A child node must exist to represent the core DWC3 IP block. The name of
|
|
the node is not important. The content of the node is defined in dwc3.txt.
|
|
|
|
Phy documentation is provided in the following places:
|
|
Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt - USB3 QMP PHY
|
|
Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt - USB2 QUSB2 PHY
|
|
|
|
Example device nodes:
|
|
|
|
hs_phy: phy@100f8800 {
|
|
compatible = "qcom,qusb2-v2-phy";
|
|
...
|
|
};
|
|
|
|
ss_phy: phy@100f8830 {
|
|
compatible = "qcom,qmp-v3-usb3-phy";
|
|
...
|
|
};
|
|
|
|
usb3_0: usb30@a6f8800 {
|
|
compatible = "qcom,dwc3";
|
|
reg = <0xa6f8800 0x400>;
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
ranges;
|
|
|
|
interrupts = <0 131 0>, <0 486 0>, <0 488 0>, <0 489 0>;
|
|
interrupt-names = "hs_phy_irq", "ss_phy_irq",
|
|
"dm_hs_phy_irq", "dp_hs_phy_irq";
|
|
|
|
clocks = <&gcc GCC_USB30_PRIM_MASTER_CLK>,
|
|
<&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
|
|
<&gcc GCC_USB30_PRIM_SLEEP_CLK>;
|
|
clock-names = "core", "mock_utmi", "sleep";
|
|
|
|
assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
|
|
<&gcc GCC_USB30_PRIM_MASTER_CLK>;
|
|
assigned-clock-rates = <19200000>, <133000000>;
|
|
|
|
resets = <&gcc GCC_USB30_PRIM_BCR>;
|
|
reset-names = "core_reset";
|
|
power-domains = <&gcc USB30_PRIM_GDSC>;
|
|
qcom,select-utmi-as-pipe-clk;
|
|
|
|
dwc3@10000000 {
|
|
compatible = "snps,dwc3";
|
|
reg = <0x10000000 0xcd00>;
|
|
interrupts = <0 205 0x4>;
|
|
phys = <&hs_phy>, <&ss_phy>;
|
|
phy-names = "usb2-phy", "usb3-phy";
|
|
dr_mode = "host";
|
|
};
|
|
};
|
|
|