97 lines
3.2 KiB
Plaintext
Executable file
97 lines
3.2 KiB
Plaintext
Executable file
config USB_MTK_HDRC
|
|
tristate "MediaTek MUSB support"
|
|
select USB_GADGET_SELECTED
|
|
select USB_GADGET_DUALSPEED
|
|
help
|
|
Say Y here if your system has a high speed USB
|
|
controller based on the MTK MUSB IP. Then
|
|
configure options to match your silicon and the board
|
|
it's being used with, including the USB peripheral role,
|
|
or the USB host role, or both.
|
|
|
|
config MTK_MUSB_QMU_SUPPORT
|
|
bool "QMU Transfer mode of MediaTek MUSB"
|
|
depends on USB_MTK_HDRC
|
|
help
|
|
Say Y here if your system has a QMU capability for USB
|
|
controller based on the MTK MUSB IP.
|
|
QMU is some kind of enhanced DMA mode by HW queeu rather
|
|
than SW queue to reduce SW effort.
|
|
|
|
config MTK_MUSB_QMU_PURE_ZLP_SUPPORT
|
|
bool "Transfer ZLP by GDP of MediaTek MUSB"
|
|
depends on MTK_MUSB_QMU_SUPPORT
|
|
help
|
|
Say Y here if QMU IP supports sending zero
|
|
length packet(ZLP) by setting ZLP flag in GDP
|
|
and the driver can enable by internal register.
|
|
After MT6763 should support this feature.
|
|
|
|
config MTK_MUSB_DRV_36BIT
|
|
tristate "MediaTek MUSB 36bits addressing support"
|
|
default n
|
|
help
|
|
This selects the MediaTek MUSB support 36-bits
|
|
address accessing.
|
|
Say Y here if you want to enable 36-bits addressing support.
|
|
If unsure, say N.
|
|
|
|
config USB_MTK_OTG
|
|
bool "MediaTek MUSB OTG support"
|
|
help
|
|
Enable Mediatek USB Host OTG detection mechanism
|
|
and USB-IF Compliance Test Program.
|
|
1. IDDIG - OTG cable attachment detection.
|
|
2. DRVVBUS - provides the VBUS for the attached devices
|
|
|
|
config USB_MTK_CHARGER_DETECT
|
|
bool "MediaTek MUSB charger detect"
|
|
depends on MTK_USBFSH
|
|
help
|
|
If make port1 enable in mt8163, please open the config.
|
|
When port0 is using, plug in device to port1,
|
|
port0 will get the disconnect. fix the issue, need open
|
|
the config.
|
|
|
|
config MTK_UART_USB_SWITCH
|
|
bool "MediaTek UART could use USB DATA pins"
|
|
help
|
|
This is a feature for debugging purpose.
|
|
It uses the USB TX/RX as UART TX/RX.
|
|
A USB to UART cable is needed to use this feature.
|
|
Using the UI in the EngineerMode to switch between USB and UART mode.
|
|
After switching to UART mode and connect to the PC with a USB to UART cable,
|
|
you can connect to a Virtual COM port on the PC and get the log output to the UART console.
|
|
|
|
config MTK_MUSB_CARPLAY_SUPPORT
|
|
bool "MediaTek MUSB Carplay support"
|
|
help
|
|
Say Y here if your want to use carplay.
|
|
|
|
config MTK_MUSB_SW_WITCH_MODE
|
|
bool "MediaTek MUSB provide user space interface to switch usb role without id pin"
|
|
help
|
|
Usb host/device/idle mode switch through command, not only depend on ID pin.
|
|
Say Y here if your want to use software to switch usb mode.
|
|
|
|
config MTK_MUSB_PORT0_LOWPOWER_MODE
|
|
bool "MediaTek MUSB PORT0 low power mode support"
|
|
help
|
|
Dynamic control the usb port0 clock when PORT1 not exist.
|
|
Say Y here if your want to enable port0 low power mode for saving power.
|
|
|
|
config MTK_MUSB_DUAL_ROLE
|
|
bool "Mediatek MUSB Dual Role mode support"
|
|
select USB_ROLE_SWITCH
|
|
help
|
|
This is the default mode of working of MTK MUSB controller
|
|
where both host and gadget
|
|
features are enabled.
|
|
It is better to be be used with Mediatek extcon and tphy support.
|
|
Say Y here if your want to use usb role switch.
|
|
|
|
config MTK_MUSB_PHY
|
|
tristate "MediaTek USB20 PHY support"
|
|
help
|
|
MediaTek USB20 PHY support.
|