158 lines
5.1 KiB
C
Executable file
158 lines
5.1 KiB
C
Executable file
/*
|
|
* Copyright © 2009 - Maxim Levitsky
|
|
* driver for Ricoh xD readers
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License version 2 as
|
|
* published by the Free Software Foundation.
|
|
*/
|
|
|
|
#include <linux/pci.h>
|
|
#include <linux/completion.h>
|
|
#include <linux/workqueue.h>
|
|
#include <linux/mtd/rawnand.h>
|
|
#include <linux/spinlock.h>
|
|
|
|
|
|
/* nand interface + ecc
|
|
byte write/read does one cycle on nand data lines.
|
|
dword write/read does 4 cycles
|
|
if R852_CTL_ECC_ACCESS is set in R852_CTL, then dword read reads
|
|
results of ecc correction, if DMA read was done before.
|
|
If write was done two dword reads read generated ecc checksums
|
|
*/
|
|
#define R852_DATALINE 0x00
|
|
|
|
/* control register */
|
|
#define R852_CTL 0x04
|
|
#define R852_CTL_COMMAND 0x01 /* send command (#CLE)*/
|
|
#define R852_CTL_DATA 0x02 /* read/write data (#ALE)*/
|
|
#define R852_CTL_ON 0x04 /* only seem to controls the hd led, */
|
|
/* but has to be set on start...*/
|
|
#define R852_CTL_RESET 0x08 /* unknown, set only on start once*/
|
|
#define R852_CTL_CARDENABLE 0x10 /* probably (#CE) - always set*/
|
|
#define R852_CTL_ECC_ENABLE 0x20 /* enable ecc engine */
|
|
#define R852_CTL_ECC_ACCESS 0x40 /* read/write ecc via reg #0*/
|
|
#define R852_CTL_WRITE 0x80 /* set when performing writes (#WP) */
|
|
|
|
/* card detection status */
|
|
#define R852_CARD_STA 0x05
|
|
|
|
#define R852_CARD_STA_CD 0x01 /* state of #CD line, same as 0x04 */
|
|
#define R852_CARD_STA_RO 0x02 /* card is readonly */
|
|
#define R852_CARD_STA_PRESENT 0x04 /* card is present (#CD) */
|
|
#define R852_CARD_STA_ABSENT 0x08 /* card is absent */
|
|
#define R852_CARD_STA_BUSY 0x80 /* card is busy - (#R/B) */
|
|
|
|
/* card detection irq status & enable*/
|
|
#define R852_CARD_IRQ_STA 0x06 /* IRQ status */
|
|
#define R852_CARD_IRQ_ENABLE 0x07 /* IRQ enable */
|
|
|
|
#define R852_CARD_IRQ_CD 0x01 /* fire when #CD lights, same as 0x04*/
|
|
#define R852_CARD_IRQ_REMOVE 0x04 /* detect card removal */
|
|
#define R852_CARD_IRQ_INSERT 0x08 /* detect card insert */
|
|
#define R852_CARD_IRQ_UNK1 0x10 /* unknown */
|
|
#define R852_CARD_IRQ_GENABLE 0x80 /* general enable */
|
|
#define R852_CARD_IRQ_MASK 0x1D
|
|
|
|
|
|
|
|
/* hardware enable */
|
|
#define R852_HW 0x08
|
|
#define R852_HW_ENABLED 0x01 /* hw enabled */
|
|
#define R852_HW_UNKNOWN 0x80
|
|
|
|
|
|
/* dma capabilities */
|
|
#define R852_DMA_CAP 0x09
|
|
#define R852_SMBIT 0x20 /* if set with bit #6 or bit #7, then */
|
|
/* hw is smartmedia */
|
|
#define R852_DMA1 0x40 /* if set w/bit #7, dma is supported */
|
|
#define R852_DMA2 0x80 /* if set w/bit #6, dma is supported */
|
|
|
|
|
|
/* physical DMA address - 32 bit value*/
|
|
#define R852_DMA_ADDR 0x0C
|
|
|
|
|
|
/* dma settings */
|
|
#define R852_DMA_SETTINGS 0x10
|
|
#define R852_DMA_MEMORY 0x01 /* (memory <-> internal hw buffer) */
|
|
#define R852_DMA_READ 0x02 /* 0 = write, 1 = read */
|
|
#define R852_DMA_INTERNAL 0x04 /* (internal hw buffer <-> card) */
|
|
|
|
/* dma IRQ status */
|
|
#define R852_DMA_IRQ_STA 0x14
|
|
|
|
/* dma IRQ enable */
|
|
#define R852_DMA_IRQ_ENABLE 0x18
|
|
|
|
#define R852_DMA_IRQ_MEMORY 0x01 /* (memory <-> internal hw buffer) */
|
|
#define R852_DMA_IRQ_ERROR 0x02 /* error did happen */
|
|
#define R852_DMA_IRQ_INTERNAL 0x04 /* (internal hw buffer <-> card) */
|
|
#define R852_DMA_IRQ_MASK 0x07 /* mask of all IRQ bits */
|
|
|
|
|
|
/* ECC syndrome format - read from reg #0 will return two copies of these for
|
|
each half of the page.
|
|
first byte is error byte location, and second, bit location + flags */
|
|
#define R852_ECC_ERR_BIT_MSK 0x07 /* error bit location */
|
|
#define R852_ECC_CORRECT 0x10 /* no errors - (guessed) */
|
|
#define R852_ECC_CORRECTABLE 0x20 /* correctable error exist */
|
|
#define R852_ECC_FAIL 0x40 /* non correctable error detected */
|
|
|
|
#define R852_DMA_LEN 512
|
|
|
|
#define DMA_INTERNAL 0
|
|
#define DMA_MEMORY 1
|
|
|
|
struct r852_device {
|
|
void __iomem *mmio; /* mmio */
|
|
struct nand_chip *chip; /* nand chip backpointer */
|
|
struct pci_dev *pci_dev; /* pci backpointer */
|
|
|
|
/* dma area */
|
|
dma_addr_t phys_dma_addr; /* bus address of buffer*/
|
|
struct completion dma_done; /* data transfer done */
|
|
|
|
dma_addr_t phys_bounce_buffer; /* bus address of bounce buffer */
|
|
uint8_t *bounce_buffer; /* virtual address of bounce buffer */
|
|
|
|
int dma_dir; /* 1 = read, 0 = write */
|
|
int dma_stage; /* 0 - idle, 1 - first step,
|
|
2 - second step */
|
|
|
|
int dma_state; /* 0 = internal, 1 = memory */
|
|
int dma_error; /* dma errors */
|
|
int dma_usable; /* is it possible to use dma */
|
|
|
|
/* card status area */
|
|
struct delayed_work card_detect_work;
|
|
struct workqueue_struct *card_workqueue;
|
|
int card_registred; /* card registered with mtd */
|
|
int card_detected; /* card detected in slot */
|
|
int card_unstable; /* whenever the card is inserted,
|
|
is not known yet */
|
|
int readonly; /* card is readonly */
|
|
int sm; /* Is card smartmedia */
|
|
|
|
/* interrupt handling */
|
|
spinlock_t irqlock; /* IRQ protecting lock */
|
|
int irq; /* irq num */
|
|
/* misc */
|
|
void *tmp_buffer; /* temporary buffer */
|
|
uint8_t ctlreg; /* cached contents of control reg */
|
|
};
|
|
|
|
#define dbg(format, ...) \
|
|
if (debug) \
|
|
pr_debug(format "\n", ## __VA_ARGS__)
|
|
|
|
#define dbg_verbose(format, ...) \
|
|
if (debug > 1) \
|
|
pr_debug(format "\n", ## __VA_ARGS__)
|
|
|
|
|
|
#define message(format, ...) \
|
|
pr_info(format "\n", ## __VA_ARGS__)
|