99 lines
3.8 KiB
Plaintext
99 lines
3.8 KiB
Plaintext
The device node for Mediatek USB3.0 DRD controller
|
|
|
|
Required properties:
|
|
- compatible : should be "mediatek,<soc-model>-mtu3", "mediatek,mtu3",
|
|
soc-model is the name of SoC, such as mt8173, mt2712 etc,
|
|
when using "mediatek,mtu3" compatible string, you need SoC specific
|
|
ones in addition, one of:
|
|
- "mediatek,mt8173-mtu3"
|
|
- reg : specifies physical base address and size of the registers
|
|
- reg-names: should be "mac" for device IP and "ippc" for IP port control
|
|
- interrupts : interrupt used by the device IP
|
|
- power-domains : a phandle to USB power domain node to control USB's
|
|
mtcmos
|
|
- vusb33-supply : regulator of USB avdd3.3v
|
|
- clocks : a list of phandle + clock-specifier pairs, one for each
|
|
entry in clock-names
|
|
- clock-names : must contain "sys_ck" for clock of controller,
|
|
the following clocks are optional:
|
|
"ref_ck", "mcu_ck" and "dam_ck";
|
|
- phys : see usb-hcd.txt in the current directory
|
|
- dr_mode : should be one of "host", "peripheral" or "otg",
|
|
refer to usb/generic.txt
|
|
|
|
Optional properties:
|
|
- #address-cells, #size-cells : should be '2' if the device has sub-nodes
|
|
with 'reg' property
|
|
- ranges : allows valid 1:1 translation between child's address space and
|
|
parent's address space
|
|
- extcon : external connector for vbus and idpin changes detection, needed
|
|
when supports dual-role mode.
|
|
- vbus-supply : reference to the VBUS regulator, needed when supports
|
|
dual-role mode.
|
|
- pinctrl-names : a pinctrl state named "default" is optional, and need be
|
|
defined if auto drd switch is enabled, that means the property dr_mode
|
|
is set as "otg", and meanwhile the property "mediatek,enable-manual-drd"
|
|
is not set.
|
|
- pinctrl-0 : pin control group
|
|
See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
|
|
|
|
- maximum-speed : valid arguments are "super-speed", "high-speed" and
|
|
"full-speed"; refer to usb/generic.txt
|
|
- enable-manual-drd : supports manual dual-role switch via debugfs; usually
|
|
used when receptacle is TYPE-A and also wants to support dual-role
|
|
mode.
|
|
- wakeup-source: enable USB remote wakeup of host mode.
|
|
- mediatek,syscon-wakeup : phandle to syscon used to access the register
|
|
of the USB wakeup glue layer between SSUSB and SPM; it depends on
|
|
"wakeup-source", and has two arguments:
|
|
- the first one : register base address of the glue layer in syscon;
|
|
- the second one : hardware version of the glue layer
|
|
- 1 : used by mt8173 etc
|
|
- 2 : used by mt2712 etc
|
|
- mediatek,u3p-dis-msk : mask to disable u3ports, bit0 for u3port0,
|
|
bit1 for u3port1, ... etc;
|
|
|
|
additionally the properties from usb-hcd.txt (in the current directory) are
|
|
supported.
|
|
|
|
Sub-nodes:
|
|
The xhci should be added as subnode to mtu3 as shown in the following example
|
|
if host mode is enabled. The DT binding details of xhci can be found in:
|
|
Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.txt
|
|
|
|
Example:
|
|
ssusb: usb@11271000 {
|
|
compatible = "mediatek,mt8173-mtu3";
|
|
reg = <0 0x11271000 0 0x3000>,
|
|
<0 0x11280700 0 0x0100>;
|
|
reg-names = "mac", "ippc";
|
|
interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_LOW>;
|
|
phys = <&phy_port0 PHY_TYPE_USB3>,
|
|
<&phy_port1 PHY_TYPE_USB2>;
|
|
power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>;
|
|
clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>,
|
|
<&pericfg CLK_PERI_USB0>,
|
|
<&pericfg CLK_PERI_USB1>;
|
|
clock-names = "sys_ck", "ref_ck";
|
|
vusb33-supply = <&mt6397_vusb_reg>;
|
|
vbus-supply = <&usb_p0_vbus>;
|
|
extcon = <&extcon_usb>;
|
|
dr_mode = "otg";
|
|
wakeup-source;
|
|
mediatek,syscon-wakeup = <&pericfg 0x400 1>;
|
|
#address-cells = <2>;
|
|
#size-cells = <2>;
|
|
ranges;
|
|
|
|
usb_host: xhci@11270000 {
|
|
compatible = "mediatek,mt8173-xhci";
|
|
reg = <0 0x11270000 0 0x1000>;
|
|
reg-names = "mac";
|
|
interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>;
|
|
power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>;
|
|
clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>;
|
|
clock-names = "sys_ck", "ref_ck";
|
|
vusb33-supply = <&mt6397_vusb_reg>;
|
|
};
|
|
};
|